Residual stresses in arc and electron-beam welds in 130 mm thick SA508 steel: Part 2 –measurements

International Journal of Pressure Vessels and Piping - Tập 172 - Trang 379-390 - 2019
A.N. Vasileiou1, M.C. Smith1, J.A. Francis1, D.W. Rathod1, J. Balakrishnan2, N.M. Irvine1
1The University of Manchester, Sackville Street, Manchester, M13 9PL, UK
2Nuclear Advanced Manufacturing Centre, Advanced Manufacturing Park, Brunel Way, Rotherham, S60 5WG, UK

Tài liệu tham khảo

Jeyaganesh, 2014, Overview of welding research under the new nuclear manufacturing (NNUMAN) programme, PVP2014

Sanderson, 2000, Advanced welding processes for fusion reactor fabrication, Fusion Eng. Des., 49–50, 77, 10.1016/S0920-3796(00)00407-5

Shono, 1988, Application of new welding technology for the manufacturing of nuclear pressure vessels, 1279

Ayres, 2010, Development of reduced pressure electron beam welding process for thick section pressure vessel welds, 39

Withers, 2007, Residual stress and its role in failure, Rep. Prog. Phys., 70, 2211, 10.1088/0034-4885/70/12/R04

2015

2007

Song, 2015, A full-field residual stress estimation scheme for fitness-for-service assessment of pipe girth welds: Part I – identification of key parameters, Int. J. Press. Vessel. Pip., 126–127, 58, 10.1016/j.ijpvp.2015.01.002

Song, 2015, A full-field residual stress estimation scheme for fitness-for-service assessment of pipe girth welds: Part II – a shell theory based implementation, Int. J. Press. Vessel. Pip., 128, 8, 10.1016/j.ijpvp.2015.01.005

Song, 2016, A framework for estimating residual stress profile in seam-welded pipe and vessel components part I: weld region, Int. J. Press. Vessel. Pip., 146, 74, 10.1016/j.ijpvp.2016.07.009

Song, 2016, A framework for estimating residual stress profile in seam welded pipe and vessel components Part II: outside of weld region, Int. J. Press. Vessel. Pip., 146, 65, 10.1016/j.ijpvp.2016.07.010

Bouchard, 2007, Validated residual stress profiles for fracture assessments of stainless steel pipe girth welds, Int. J. Press. Vessel. Pip., 84, 195, 10.1016/j.ijpvp.2006.10.006

Mathew, 2017, Prediction of residual stresses in girth welded pipes using an artificial neural network approach, Int. J. Press. Vessel. Pip., 150, 89, 10.1016/j.ijpvp.2017.01.002

Mathew, 2017, Through-thickness residual stress profiles in austenitic stainless steel welds: a combined experimental and prediction study, Metall. Mater. Trans., 48, 6178, 10.1007/s11661-017-4359-4

George, 2000

Smith, 2000, Measurement and prediction of residual stresses in thick-section steel welds, J. Strain Anal. Eng. Des., 35, 287, 10.1243/0309324001514422

Leggatt, 1996, Development and experimental validation of the deep hole method for residual stress measurement, J. Strain Anal. Eng. Des., 31, 177, 10.1243/03093247V313177

Mahmoudi, 2008, A new procedure to measure near yield residual stresses using the deep hole drilling technique, Exp. Mech., 49, 595, 10.1007/s11340-008-9164-y

Smith, 2014, Measured and predicted residual stresses in thick section electron beam welded steels, Int. J. Press. Vessel. Pip., 120–121, 66, 10.1016/j.ijpvp.2014.05.001

Vasileiou, 2016, Residual stresses in thick-section electron beam welds in RPV steels, PVP2016

Javadi, 2017, Residual stress measurement round robin on an electron beam welded joint between austenitic stainless steel 316L(N) and ferritic steel P91, Int. J. Press. Vessel. Pip., 154, 41, 10.1016/j.ijpvp.2017.06.002

Vasileiou, 2017, The impact of transformation plasticity on the electron beam welding of thick-section ferritic steel components, Nucl. Eng. Des., 323, 309, 10.1016/j.nucengdes.2017.03.040

Rathod, 2018

Bate, 2016, Determination of residual stresses in welded components by finite element analysis, Mater. Sci. Technol., 32, 1505, 10.1080/02670836.2016.1209882

Smith, 2017, A review of welding research within the new nuclear manufacturing (NNUMAN) programme

Feng, 2017, An evaluation of multipass narrow gap laser welding as a candidate process for the manufacture of nuclear pressure vessels, Int. J. Press. Vessel. Pip., 157, 43, 10.1016/j.ijpvp.2017.08.004

Balakrishnan, 2018, Residual stress distributions in arc, laser and electron-beam welds in 30 mm thick SA508 steel: a cross-process comparison, Int. J. Press. Vessel. Pip., 162, 59, 10.1016/j.ijpvp.2018.03.004

Rathod, 2017, Thermal cycle-dependent metallurgical variations and their effects on the through-thickness mechanical properties in thick section narrow-gap welds, Mater. Sci. Eng., A, 707, 399, 10.1016/j.msea.2017.09.044

Sun, 2017, Evaluation of errors associated with cutting-induced plasticity in residual stress measurements using the contour method, Exp. Mech., 57, 719, 10.1007/s11340-017-0255-5

Hosseinzadeh, 2012

Muránsky, 2016, Mitigating cutting-induced plasticity in the contour method. Part 2: numerical analysis, Int. J. Solids Struct., 94–95, 254, 10.1016/j.ijsolstr.2015.12.033

Hosseinzadeh, 2016, Mitigating cutting-induced plasticity in the contour method, part 1: Experimental, Int. J. Solids Struct., 94–95, 247, 10.1016/j.ijsolstr.2015.12.034

Murakawa, 2010, Effect of low transformation temperature weld filler metal on welding residual stress, Sci. Technol. Weld. Join., 15, 393, 10.1179/136217110X12714217309614

Serasli, 2015

Thông tin
Thông tin xuất bản

International Journal of Pressure Vessels and Piping

Tập 172

379-390

Thông tin tác giả