Measured and predicted residual stresses in thick section electron beam welded steels

Schultz, 1993 Venkata Ramana, 2010, Microstructure and residual stress distribution of similar and dissimilar electron beam welds – maraging steel to medium alloy medium carbon steel, Mater Des, 31, 749, 10.1016/j.matdes.2009.08.007 Sanderson, 2000, Advanced welding processes for fusion reactor fabrication, Fusion Eng Des, 49–50, 77, 10.1016/S0920-3796(00)00407-5 Ayres K, Hurrell P, Gill C, Bridger K, Burling LD, Punshon C, et al. Development of reduced pressure electron beam welding process for thick section pressure vessel welds. In: PVP2010-25957. 2010. Huang, 1997, Effects of post-weld heat treatments on the residual stress and mechanical properties of electron beam welded SAE 4130 steel plates, J Mater Eng Perform, 6, 61, 10.1007/s11665-997-0033-0 Allen, 1995, Study of residual stress in a ferritic steel electron beam test weldments using neutron diffraction, Mater Lett, 23, 265, 10.1016/0167-577X(95)00028-3 Stone, 1999, Comparison of three different techniques for measuring residual stresses in an electron beam-welded WASPALOY, Metall Mater Trans, 30A, 1797, 10.1007/s11661-999-0178-6 Webster, 2001, Non-destructive measurement of residual stress by neutron diffraction, J Mater Process Technol, 117, 395, 10.1016/S0924-0136(01)00802-0 Cho, 2003, Residual stresses in an electron beam weld of Ti834: characterisation and numerical modelling, Metall Mater Trans A, 34A, 2935, 10.1007/s11661-003-0193-y Brown, 2011, Critical comparison of two independent measurements of residual stresses in an electron-beam welded uranium cylinder: neutron diffraction and the contour method, Acta Mater, 59, 864, 10.1016/j.actamat.2010.09.022 Woo, 2011, Neutron diffraction measurements of residual stresses in a 50 mm thick weld, Mater Sci Eng, 528, 4120, 10.1016/j.msea.2011.02.009 Ueda, 1986, Measurement of three-dimensional welding residual stresses due to electron beam welding, Trans JWRI, 15, 125 Asano, 2006, Long-term integrity of waste package final closure for HLW geological disposal (III); applicability of electron beam welding to overpack final closure, J Nucl Sci Technol, 43, 206, 10.1080/18811248.2006.9711083 Kingston, 2010, Measurement of residual stresses in thick section steel electron beam welds Ficquet, 2011, Measurement of residual stresses in thick section pressure electron beam welded components Zheng G, Smith DJ, Hurrell P, Goudar DM, Kingston E. A new procedure for measuring residual stresses in electron beam welds using the deep hole drilling technique. In: SEM Conference 2011. Faure, 1996, Residual stresses in austenitic stainless steel primary coolant pipes and welds of pressurized water reactors, Int J Vess Pip, 65, 265, 10.1016/0308-0161(94)00137-8 Pagliaro, 2010, Measuring multiple residual-stress components using the contour method and multiple cuts, Exp Mech, 50, 187, 10.1007/s11340-009-9280-3 Sysweld_ Finite Element Software. Systus International; Paris, France. [Quoted by Ref. [9]]. Rosenthal, 1945, A method of measuring triaxial residual stresses in plates, Weld J, 295s Leggatt, 1996, Development and experimental validation of the deep hole method for residual stress measurement, J Strain Analysis Eng Des, 31, 177, 10.1243/03093247V313177 Smith, 2000, Measurement and prediction of residual stresses in thick-section steel welds, J Strain Analysis Eng Des, 35, 287, 10.1243/0309324001514422 Brown, 2006, Predictions and measurements of residual stress in repair welds in plates, Int J Press Vess Pip, 83, 809, 10.1016/j.ijpvp.2006.08.012 Kingston, 2006, Novel applications of the deep-hole drilling technique for measuring through-thickness residual stress distributions, J ASTM Int, 3 Mahmoudi, 2009, A new procedure to measure near yield residual stresses using the deep hole drilling technique, Exp Mech, 49, 595, 10.1007/s11340-008-9164-y Hossain, 2011, Finite element validation of the over-coring deep-hole drilling technique, Appl Mech Mater, 70, 291, 10.4028/www.scientific.net/AMM.70.291 Moinereau, 2010, NESC VII; a European project for application of WPS in RPV assessment including biaxial loading Granada-Garcia, 1998, Assessment of distortions in the deep hole technique for measuring residual stresses VFT, 2006 2008 Lemaitre, 1990 Goudar, 2009, Evaluating uncertainty in residual stress measured using the deep-hole drilling technique, Strain, 47, 62, 10.1111/j.1475-1305.2009.00620.x Zheng, 2013 Smith, 2009, NeT bead-on-plate round robin: comparison of residual stress predictions and measurements, Int J Press Vess Pip, 86, 79, 10.1016/j.ijpvp.2008.11.017