A New Procedure to Measure Near Yield Residual Stresses Using the Deep Hole Drilling Technique

Mahmoudi AH, Truman CE, Smith DJ (2008) Using local out-of-plane compression (LOPC) to study the effects of residual stress on apparent fracture toughness. Eng Fract Mech 75:1516–1534.

Smith DJ (2003) The influence of the prior loading on structural integrity, 7, chapter 9. In: Ainsworth RA, Schwalbe KH (eds) Comprehensive structural integrity. Elsevier, London.

Withers PJ, Bhadeshia HKDH (2001) Residual stresses, part 1—measurement techniques. Mater Sci Technol 174:355–365.

Schajer GS (1998) Measurement of non-uniform residual stresses using the hole drilling method part I and part II. J Eng Mater Technol 1104:338–349.

Cheng W, Finnie I (1986) Measurement of residual hoop stresses in cylinders using the compliance method. Trans ASME J Eng Mater Technol 1082:87–92.

Lee MJ, Hill MR (2007) Effect of strain gage length when determining residual stress by slitting. J Eng Mater Technol 1291:143–150. doi: 10.1115/1.2400263 .

Garcia-Granada AA, Smith DJ, Pavier MJ (2000) A new procedure based on Sachs boring for measuring non-axisymmetric residual stresses. Int J Mech Sci 426:1027–1047. doi: 10.1016/S0020-7403(99)00039-9 .

Rosenthal D, Norton JT (1945) A method of measuring triaxial residual stresses in plates. J Weld Res 24Suppl:295–307.

Zhdanov IM, Gonchar AK (1978) Determination of welding residual stresses at a depth in metals. Autom Weld 319:22–24.

Beaney EM (1978) Measurement of sub-surface stresses. CEBG Report No. RD/B/N 4323.

Smith DJ, Bonner NW (1994) Measurement of residual stresses in a thick section steel weld. In: Edward JH, Kerr J, Stanely P (eds) Engineering integrity assessment. Engineering Materials Advisory Services Chamelon Press, Birmingham, pp 259–274.

Bonner NW (1996) Measurement of residual stresses in thick steel Welds. PhD thesis, University of Bristol.

Mahmoudi AH, Stefanescu D, Hossain S, Truman CE, Smith DJ (2006) Measurement and prediction of residual stress field generated by side-punching. J Eng Mater Technol 1283:451–459. doi: 10.1115/1.2203103 .

Bateman MG, Miller OH, Palmer TJ, Breen CEP, Kingston EJ, Smith DJ et al (2005) Measurement of residual stress in thick section composite laminates using the deep-hole method. Int J Mech Sci 4711:1718–1739. doi: 10.1016/j.ijmecsci.2005.06.011 .

George D, Kingston E, Smith DJ (2002) Measurement of through thickness stresses using small holes. J Strain Anal 372:125–139. doi: 10.1243/0309324021514899 .

Kingston EJ, Stefanescu D, Mahmoudi AH, Truman CE, Smith DJ (2006) Novel applications of the deep-hole drilling technique for measuring through-thickness residual stress distributions. J ASTM International 3(4). doi: 10.1520/JAI12568 .

Lin YC, Chou CP (1995) Error induced by local yielding around hole in hole drilling method for measuring residual stress of materials. J Mar Sci Technol 116:600–604.

Gibmeier J, Kornmeier M, Scholtes B (2000) Plastic deformation during application of the hole drilling method. Mat Sci Forum 347–349:131–136.

Vangi D, Ermini M (2000) Plasticity effects in residual stress measurement by the hole drilling method. Strain 362:255–259.

Beghini M, Bertini L (2000) Analytical expressions of the influence functions for accuracy and versatility improvement in the hole drilling method. J Strain Anal 352:125–135. doi: 10.1243/0309324001514071 .

Beghini M, Bertini L, Raffaelli P (1994) Numerical analysis of plasticity effects in the hole-drilling residual stress measurement. J Test Eval 226:522–529.

Prime MB (2001) Cross-sectional mapping of residual stresses by measuring the surface contour after a cut. J Eng Mater Technol 1232:162–168. doi: 10.1115/1.1345526 .

Shin SH (2005) FEM analysis of plasticity-induced error on measurement of welding residual stress by the contour method. J Mech Sci Technol 1910:1885–1890.

Mahmoudi AH, Pavier MJ, Truman CE, Smith DJ (2007) Accurate measurement of highly triaxial residual stresses. Proceedings of the Society for Experimental Mechanics (SEM) Conference, Springfield, Massachusetts, USA, CD.

Smith DJ, Bouchard PJ, George D (2000) Measurement and prediction of residual stresses in thick section steel welds. J Strain Anal 354:287–305. doi: 10.1243/0309324001514422 .

Kingston E (2003) Advances in the deep hole drilling technique for residual stress measurement. PhD thesis, University of Bristol.

ABAQUS Users Manuals, version 6.4 (2006) Hibbit Karlsson, Sorenson Inc., 1080 Main street, Pawtucket RI, 02860-4847, USA

Hossain S (2005) Residual stresses under conditions of high triaxiality. PhD thesis, University of Bristol.

Fitzpatrick ME, Lodini A (2003) Analysis of residual stress by diffraction using neutron and synchrotron radiation. Taylor and Francis, London.