Residual stress distributions in arc, laser and electron-beam welds in 30 mm thick SA508 steel: A cross-process comparison

Sanderson, 2000, Advanced welding processes for fusion reactor fabrication, Fusion Eng Des, 49–50, 77, 10.1016/S0920-3796(00)00407-5 Ayres, 2010, Development of reduced pressure electron beam welding process for thick section pressure vessel welds Lidbury, 1984, The significance of residual stresses in relation to the integrity of LWR pressure vessels, Int J Pres Ves Pip, 17, 197, 10.1016/0308-0161(84)90028-0 Read, 1989, Measurement of applied J-Integral produced by residual-stress, Eng Fract Mech, 32, 147, 10.1016/0013-7944(89)90212-9 Hornbach, 2002, The effect of prior cold work on tensile residual stress development in nuclear weldments, J. Pressure Vessel Technol. - Trans. ASME, 124, 359, 10.1115/1.1481035 Radaj, 1992, 1 2009 Francis, 2007, Review – “welding residual stresses in ferritic power-plant steels”, Mater Sci Technol, 23, 1009, 10.1179/174328407X213116 Smith, 2014, Measured and predicted residual stresses in thick section electron beam welded steels, Int J Pres Ves Pip, 120–121, 66, 10.1016/j.ijpvp.2014.05.001 Francis, 2009, Measured residual stress distributions for low and high heat-input single weld beads deposited on to SA508 steel, Mater Sci Technol, 25, 325, 10.1179/174328408X372074 Guo, 2015, Microstructure and mechanical characteristics of a laser welded joint in SA508 nuclear pressure vessel steel, Mater Sci Eng, 625, 65, 10.1016/j.msea.2014.11.056 Mark, 2012, Evolution of local material properties and residual stress due to thermal cycling in a multipass SA508 steel weld, Acta Mater, 60, 3268, 10.1016/j.actamat.2012.03.022 Feng, 2017, An evaluation of multipass narrow gap laser welding as a candidate process for the manufacture of nuclear pressure vessels, Int J Pres Ves Pip, 157, 43, 10.1016/j.ijpvp.2017.08.004 Jeyaganesh, 2014, Overview of welding research under the new nuclear manufacturing (NNUMAN) programme, 6B Odette, 1983, On the dominant mechanism of irradiation embrittlement of reactor pressure vessels steels”, Scripta Metall, 17, 1183, 10.1016/0036-9748(83)90280-6 Francis, 2009, The effects of filler metal transformation temperature on residual stresses in a high strength steel weld, J Pressure Vessel Technol, 131, 10.1115/1.3122036 Kundu, 2013, Residual stresses in P91 steel electron beam welds, Sci Technol Weld Join, 18, 70, 10.1179/1362171812Y.0000000076 Withers, 2007, Residual stress and it role in failure, Rep Prog Phys, 70, 2211, 10.1088/0034-4885/70/12/R04 Pawley, 1980, EDINP, the edinburgh powder profile refinement program, J Appl Crystallogr, 13, 630, 10.1107/S0021889880012964 Larson, 1986 Daymond, 2002, Elastoplastic deformation of ferritic steel and cementite studied by neutron diffraction and self-consistent modelling, Acta Mater, 50, 1613, 10.1016/S1359-6454(02)00026-5 Krawitz, 1994, Use of position-dependent stress-free standards for diffraction stress measurements, Mater Sci Eng, 185, 123, 10.1016/0921-5093(94)90935-0 Prime, 2001, Cross-sectional mapping of residual stresses by measuring the surface contour after a cut, J Eng Mater Technol, 123, 162, 10.1115/1.1345526 Traoré, 2014, Plasticity in the contour method of residual stress measurement, Adv Mater Res, 996, 337, 10.4028/www.scientific.net/AMR.996.337 Sun, 2017, Evaluation of errors associated with cutting-induced plasticity in residual stress measurements using the contour method, Exp Mech, 57, 719, 10.1007/s11340-017-0255-5 Javadi, 2017, Measurement of residual stresses induced by sequential weld buttering and cladding operations involving a 2.25Cr-1Mo substrate material, Int J Pres Ves Pip, 154, 58, 10.1016/j.ijpvp.2017.06.003 Johnson, 2008, 243 F. Hosseinzadeh, J. Kowal and P. J. Bouchard: Towards good practice guidelines for the contour method of residual stress measurement, The Journal of Engineering, https://doi.org/10.1049/joe.2014.0134. Prime, 2004, Laser surface-contouring and spline data-smoothing for residual stress measurement, Exp Mech, 44, 176, 10.1007/BF02428177 Smith, 2017, A review of welding research within the New Nuclear Manufacturing (NNUMAN) programme Ohms, 2013