Mitigating cutting-induced plasticity in the contour method, part 1: Experimental

B.M.G. Biritish Energy, and Serco Assurance, 2009 Bueckner, 1973, Field Singularities and Related Integral Representations, Mechanics of Fracture, 239 Citarella, 2015, Numerical–experimental crack growth analysis in AA2024-T3 FSWed butt joints, Adv. Eng. Softw., 80, 47, 10.1016/j.advengsoft.2014.09.018 Dennis, 2008, Assessment of the influence of plasticity on measurement residual stresses using the contour method Hamelin, 2014, Validation of a numerical model used to predict phase distribution and residual stress in ferritic steel weldments, Acta Mater., 75, 1, 10.1016/j.actamat.2014.04.045 Hosseinzadeh, 2012, Residual stress measurement of a ferritic bead on plate benchmark test specimen using the contour method Hosseinzadeh, 2014, Towards good practice guidelines for the contour method of residual stress measurement, J. Eng., 1 Hosseinzadeh, 2013, Controlling the cut in contour residual stress measurements of electron beam welded Ti-6Al-4v alloy plates, Exp. Mech., 53, 829, 10.1007/s11340-012-9686-1 I.T. 21432:2005. Non-Destructive Testing-Standard Test Method for Determining Residual Stresses by Neutron Diffraction. 2005. Janssen, 2002 Martins, 2010, Full 3D spatially resolved mapping of residual strain in a 316L austenitic stainless steel weld specimen, Mater. Sci. Eng. A, 527, 4779, 10.1016/j.msea.2010.03.110 Muránsky, 2012, Comprehensive numerical analysis of a three-pass bead-in-slot weld and its critical validation using neutron and synchrotron diffraction residual stress measurements, Int. J. Solids Struct., 49, 1045, 10.1016/j.ijsolstr.2011.07.006 Muránsky, 2014, Numerical analysis of retained residual stresses in C(T) specimen extracted from a multi-pass austenitic weld and their effect on crack growth, Eng. Fract. Mech., 126, 40, 10.1016/j.engfracmech.2014.04.008 Muránsky, 2016, Int. J. Solids Struct Paulo, 2014, Influence of friction stir welding residual stresses on the compressive strength of aluminium alloy plates, Thin-Walled Struct., 74, 184, 10.1016/j.tws.2013.09.012 Prime, 2001, Cross-sectional mapping of residual stresses by measuring the surface contour after a cut, J. Eng. Mater. Technol., 123, 162, 10.1115/1.1345526 Prime, 2013, The contour method, 109 Prime, 2010, The contour method cutting assumption: error minimization and correction Prime, 2004, Laser surface-contouring and spline data-smoothing for residual stress measurement, Exp. Mech., 44, 176, 10.1007/BF02428177 Smith, 2009, NeT bead-on-plate round robin: comparison of residual stress predictions and measurements, Int. J. Press. Vessels Pip., 86, 79, 10.1016/j.ijpvp.2008.11.017 Smith, 2014, A review of the NeT Task Group 1 residual stress measurement and analysis round robin on a single weld bead-on-plate specimen, International Journal of Pressure Vessels and Piping, 120–121, 93, 10.1016/j.ijpvp.2014.05.002 Traore, 2011, A novel cutting strategy for reducing plasticity induced errors in residual stress measurements made with the contour method Traore, 2014, Plasticity in the contour method of residual stress measurement, Adv. Mater. Res., 996, 337, 10.4028/www.scientific.net/AMR.996.337 Withers, 2007, Residual stress and its role in failure, Rep. Prog. Phys., 70, 2211, 10.1088/0034-4885/70/12/R04