Mechanism and feasibility study of low frequency vibration assisted drilling of a newly developed CFRP/Al co-cured material

Tang, 2012, Superconducting magnetic bearings and active magnetic bearings in attitude control and energy storage flywheel for spacecraft, IEEE Trans Appl Supercond, 22, 5702109, 10.1109/TASC.2012.2218245

Bangcheng, 2012, Integral design and analysis of passive magnetic bearing and active radial magnetic bearing for agile satellite application, IEEE Trans Magn, 48, 1959, 10.1109/TMAG.2011.2180731

Kenny, 2005, Integrated power and attitude control with two flywheels, IEEE Trans Aerosp Electron Syst, 41, 1431, 10.1109/TAES.2005.1561894

An, 2020, Investigation on the cutting responses of CFRP/Ti stacks: with special emphasis on the effects of drilling sequences, Compos Struct, 253, 10.1016/j.compstruct.2020.112794

An, 2018, Thermal characteristics of unidirectional carbon fiber reinforced polymer laminates during orthogonal cutting, J Reinf Plast Compos, 37, 905, 10.1177/0731684418768892

Romoli, 2019, Quality monitoring and control for drilling of CFRP laminates, J Manuf Process, 40, 16, 10.1016/j.jmapro.2019.02.028

Li, 2020, Damage behaviors of unidirectional CFRP in orthogonal cutting: a comparison between single- and multiple-pass strategies, Compos Part B Eng, 185, 10.1016/j.compositesb.2020.107774

Campbell, 2006, Chapter 8 - Adhesive bonding and integrally cocured structure, 369

Xu, 2020, On the analysis of temperatures, surface morphologies and tool wear in drilling CFRP/Ti6Al4V stacks under different cutting sequence strategies, Compos Struct, 234, 10.1016/j.compstruct.2019.111708

Wang, 2017, Occurrence and formation mechanism of surface cavity defects during orthogonal milling of CFRP laminates, Compos Part B Eng, 109, 10, 10.1016/j.compositesb.2016.10.015

Bonnet, 2015, CFRP drilling: fundamental study of local feed force and consequences on hole exit damage, Int J Mach Tools Manuf, 94, 57, 10.1016/j.ijmachtools.2015.04.006

Wang, 2015, Drilling temperature and hole quality in drilling of CFRP/aluminum stacks using diamond coated drill, Int J Precis Eng Manuf, 16, 1689, 10.1007/s12541-015-0222-y

Xu, 2019, On the interpretation of drilling CFRP/Ti6Al4V stacks using the orthogonal cutting method: chip removal mode and subsurface damage formation, J Manuf Process, 44, 435, 10.1016/j.jmapro.2019.05.052

D’Orazio, 2017, Tool wear and hole quality in drilling of CFRP/AA7075 stacks with DLC and nanocomposite TiAlN coated tools, J Manuf Process, 30, 582, 10.1016/j.jmapro.2017.10.019

Zitoune, 2012, Influence of machining parameters and new nano-coated tool on drilling performance of CFRP/Aluminium sandwich, Compos Part B Eng, 43, 1480, 10.1016/j.compositesb.2011.08.054

Liang, 2018, Investigation on the non-coaxiality in the drilling of carbon-fibre-reinforced plastic and aluminium stacks, Int J Mach Tools Manuf, 125, 1, 10.1016/j.ijmachtools.2017.11.001

Zou, 2020, Hole quality and tool wear when dry drilling of a new developed metal/composite co-cured material, Proc Inst Mech Eng Part B J Eng Manuf, 234, 980, 10.1177/0954405420901420

Shao, 2021, The interface temperature and its influence on surface integrity in ultrasonic-assisted drilling of CFRP/Ti stacks, Compos Struct, 266, 10.1016/j.compstruct.2021.113803

Li, 2019, Tool wear processes in low frequency vibration assisted drilling of CFRP/Ti6Al4V stacks with forced air-cooling, Wear, 426–427, 1616, 10.1016/j.wear.2019.01.005

Yang, 2020, Chip control analysis in low-frequency vibration-assisted drilling of Ti–6Al–4V titanium alloys, Int J Precis Eng Manuf, 21, 565, 10.1007/s12541-019-00286-8

An, 2015, Study on the cutting mechanics characteristics of high-strength UD-CFRP laminates based on orthogonal cutting method, Compos Struct, 131, 374, 10.1016/j.compstruct.2015.05.035