Comparison of Mechanical and Tribological Properties of Nitride and Oxynitride Coatings Based on Chrome and Zirconium Obtained by Cathodic Arc Evaporation

Allerton Press - Tập 40 - Trang 163-170 - 2019
B. Warcholinski1, A. Gilewicz1, A. S. Kuprin2, G. N. Tolmachova2, V. D. Ovcharenko2, T. A. Kuznetsova3, V. A. Lapitskaya3, S. A. Chizhik3
1Koszalin University of Technology, Koszalin, Poland
2National Science Center Kharkov Institute of Physics and Technology, Kharkov, Ukraine
3A.V. Luikov Heat and Mass Transfer Institute of National Academy of Science of Belarus, Minsk, Belarus

Tóm tắt

The results of the investigation of the microstructure, crystal lattice parameter, roughness, microhardness, elasticity modulus, friction coefficient, specific volumetric wear, and adhesion strength for CrN, ZrN, Zr–O–N, and Cr–O–N coatings are presented. The coatings are formed by cathodic arc evaporation and have a cubic lattice. Addition of oxygen to the nitride CrN and ZrN coatings leads to the lattice parameter increasing and the crystallite size decreasing simultaneously. The oxynitride coatings, Cr–O–N and Zr–O–N, possess improved tribological properties in comparison with nitride coatings.

Tài liệu tham khảo

Hogmark, S., Jacobson, S., and Larsson, M., Design and evaluation of tribological coatings, Wear, 2000, vol. 246, pp. 20–33.

Holmberg, K., Matthews, A., and Ronkainen, H., Coatings tribology—contact mechanisms and surface design, Tribol. Int., 1998, vol. 31, pp. 107–120.

Andreyev, M., Anishchik, V., Markova, L., and Kuznetsova, T., Ion-beam coatings based on Ni and Cr with ultradispersed diamonds—structure and properties, Vacuum, 2005, vol. 78, pp. 451–454.

Andreev, M.A., Kuznetsova, T.A., Markova, L.V., and Chekan, V.A., Wear resistance of composite chrome coatings with additives of utlradispersed diamonds, J. Frict. Wear, 2001, vol. 22, no. 4, pp. 423–428.

Vityaz’, P.A., Komarov, A.I., Komarova, V.I., and Kuznetsova, T.A., Peculiarities of triboformation of wear-resistant layers on the surface of a MAO-coating modified by fullerenes, J. Frict. Wear, 2011, vol. 32, no. 4, pp. 231–241.

Barata, A., Cunha, L., and Moura, C., Characterization of chromium nitride films produced by PVD techniques, Thin Solid Films, 2001, vols. 398–399, pp. 501–506.

Öztürk, A., Ezirmik, K.V., Kazmanlı, K., Ürgen, M., Eryılmaz, O. L., and Erdemir, A., Comparative tribological behaviors of TiN-, CrN- and MoN–Cu nanocomposite coatings, Tribol. Int., 2008, vol. 41, pp. 49–59.

Klumdoung, P., Buranawong, A., Chaiyakun, S., and Limsuwan, P., Variation of color in zirconium nitride thin films prepared at high Ar flow rates with reactive dc magnetron sputtering, Procedia Eng., 2012, vol. 32, pp. 916–921.

Warcholinski, B., Gilewicz, A., Lupicka, O., Kuprin, A.S., Tolmachova, G.N., Ovcharenko, V.D., Kolodiy, I.V., Sawczak, M., Kochmanska, A.E., Kochmanski, P., Kuznetsova, T.A., Zubar, T.I., Khudoley, A.L., and Chizhik, S.A., Structure of CrON coatings formed in vacuum arc plasma fluxes, Surf. Coat. Technol., 2017, vol. 309, pp. 920–930.

Kuznetsova, T.A., Andreev, M.A., and Markova, L.V., Research of wear resistance of the combined vacuum electroarc coatings on the basis of ZrHf, J. Frict. Wear, 2005, vol. 26, no. 5, pp. 521–529.

Münz, W.-D., Smith, I.J., Lewis, D.B., and Creasey, S., Droplet formation on steel substrates during cathodic steered arc metal ion etching, Vacuum, 1997, vol. 48, pp. 473–481.

Warcholiński, B., Gilewicz, A., Kukliński, Z., and Myśliński, P., Arc-evaporated CrN, CrN and CrCN coatings, Vacuum, 2008, vol. 83, pp. 715–718.

Leyland, A. and Matthews, A., On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimized tribological behavior, Wear, 2000, vol. 246, pp. 1–11.

Thông tin
Thông tin xuất bản

Allerton Press

Tập 40

163-170

Thông tin tác giả