Surface Quality Modification Using Powder Metallurgy Processed CuW Electrode During Electric Discharge Machining of Inconel 718

Procedia Materials Science - Tập 5 - Trang 2629-2634 - 2014
Naveen Beri1, Sachin Maheshwari2, Chitra Sharma3, Anil Kumar1
1Department of Mechanical Engineering, Beant College of Engineering and Technology, Gurdaspur, 143521, Punjab, India
2Division of Manufacturing Process & Automation Engineering, Netaji Subhas Institute of Technology, Dwarka, New Delhi,110078. India
3Department of Mechanical and Automation Engineering, IGIT, Kashmere Gate, Delhi, 110403. India

Tài liệu tham khảo

Ahmed, 2008, Neutron diffraction residual strain measurements in post-treated thermal spray cermet coatings, Materials Science and Engineering A, 498, 191, 10.1016/j.msea.2008.08.023

Arthur, 1996, Using rapid prototyping to produce electrical discharge machining electrodes, Journal of Rapid Prototyping., 2, 4, 10.1108/13552549610109036

Beri, 2012, Evaluation of surface quality during electrical discharge machining of Inconel 718 with powder metallurgy electrodes, Advanced Materials Research., 410, 245, 10.4028/www.scientific.net/AMR.410.245

Beri, 2011, Machining performance evaluation during electric discharge machining of Inconel 718 using the Taguchi methodology, Journal of Mechanical Engineering (solvak), 62, 299

Beri, 2010, Technological Advancement in Electrical Discharge Machining with Powder Metallurgy Processed Electrodes: A Review, Materials and Manufacturing Processes., 25, 1186, 10.1080/10426914.2010.512647

Ho, 2003, State of the art electrical discharge machining (EDM), International Journal of Machine Tools and Manufacture, 43, 1287, 10.1016/S0890-6955(03)00162-7

Ho, 2007, Use of powder metallurgy (PM) compacted electrode for electrical discharge surface alloying/modification of Ti–6Al–4V alloy, Journal of Materials Processing Technology., 191, 123, 10.1016/j.jmatprotec.2007.03.003

Kumar, 2009, Surface modification by electric discharge machining: A review, Journal of Materials Processing Technology., 209, 3675, 10.1016/j.jmatprotec.2008.09.032

Lee, 2000, Characteristic analysis of EDMed surfaces using the Taguchi approach, Materials and Manufacturing Processes., 15, 781, 10.1080/10426910008913021

Murray, 2012, Workpiece debris deposition on tool electrode and secondary discharge phenomena in micro- EDM, Journal of Materials Processing Technology., 212, 1537, 10.1016/j.jmatprotec.2012.02.019

Samuel, 1997, Power metallurgy tool electrodes for electrical discharge machining, International Journal of Machine Tools and Manufacture., 37, 1625, 10.1016/S0890-6955(97)00006-0

Samuel, 1996, Properties of compacted, pre-sintered and fully sintered electrodes produced by powder metallurgy for electric discharge machining, Indian Journal of Engineering and Material Sciences., 3, 229

Srivastava, 2013, Study of ultrasonic assisted cryogenically cooled EDM process using sintered (Cu–TiC) tooltip, Journal of Manufacturing Processes., 15, 158, 10.1016/j.jmapro.2012.12.002

Tsai, 2003, EDM performance of Cr/Cu basedcomposite electrodes, International Journal of Machine Tools and Manufacture., 43, 245, 10.1016/S0890-6955(02)00238-9

Zhu, 2003, Influence of heat treatment on microstructure and sliding wear behavior of Fe-Al/WC composite coatings, Transactions of Tianjin University., 9, 93

Thông tin
Thông tin xuất bản

Procedia Materials Science

Tập 5

2629-2634

Thông tin tác giả