International Journal of Polymer Science

Polylactic acid (PLA) is widely used in biological areas due to its excellent compatibility, bioabsorbability, and degradation behavior in human bodies. Pure polylactic acid has difficulty in meeting all the requirements that specific field may demand. Therefore, PLA based nanocomposites are extensively investigated over the past few decades. PLA based nanocomposites include PLA based copolymers in nanometer size and nanocomposites with PLA or PLA copolymers as matrix and nanofillers as annexing agent. The small scale effect and surface effect of nanomaterials help improve the properties of PLA and make PLA based nanocomposites more popular compared with pure PLA materials. This review mainly introduces different kinds of PLA based nanocomposites in recent researches that have great potential to be used in biomedical fields including bone substitute and repair, tissue engineering, and drug delivery system.

With the aim of producing xanthan gum, the effects of an aqueous shrimp shell extract (SSAE) as the source of carbon and nitrogen on the yield and apparent viscosity of the gums produced by fermentation using three native strains ofXanthomonas campestriswere studied. It was found that the SSAE contained 89.75% moisture, 0.054% ash, 8.069% protein, 0.787 lipids, and 1.337% carbohydrates. Media containing different concentrations of SSAE and supplemented with urea (0.01%) and phosphate (0.1%) were fermented in a shaker, and the results obtained were compared with those obtained from sucrose (control) with the same supplementation and fermentation conditions. Strain 1182 showed the highest yield (4.64 g·L⁻¹) and viscosity (48.53 mPa·s), from the medium containing 10% (w/v) of SSAE. These values were higher than those obtained from the control medium containing sucrose. Shrimp shell is a low cost residue that can be bioconverted into products of high added value such as xanthan gum.

The factory-produced steel-fiber reinforced polymer composite bar (SFCB) is a new kind of reinforcement for concrete structures. The manufacturing technology of SFCB is presented based on a large number of handmade specimens. The calculated stress-strain curves of ordinary steel bar and SFCB under repeated tensile loading agree well with the corresponding experimental results. The energy-dissipation capacity and residual strain of both steel bar and SFCB were analyzed. Based on the good simulation results of ordinary steel bar and FRP bar under compressive loading, the compressive behavior of SFCB under monotonic loading was studied using the principle of equivalent flexural rigidity. There are three failure modes of SFCB under compressive loading: elastic buckling, postyield buckling, and no buckling (ultimate compressive strength is reached). The increase in the postyield stiffness of SFCB rsf can delay the postyield buckling of SFCB with a large length-to-diameter ratio, and an empirical equation for the relationship between the postbuckling stress and rsf is suggested, which can be used for the design of concrete structures reinforced by SFCB to consider the effect of reinforcement buckling.

Current strategies of regenerative medicine are focused on the restoration of pathologically altered tissue architectures by transplantation of cells in combination with supportive scaffolds and biomolecules. In recent years, considerable interest has been given to biologically active scaffolds which are based on similar analogs of the extracellular matrix that have induced synthesis of tissues and organs. To restore function or regenerate tissue, a scaffold is necessary that will act as a temporary matrix for cell proliferation and extracellular matrix deposition, with subsequent ingrowth until the tissues are totally restored or regenerated. Scaffolds have been used for tissue engineering such as bone, cartilage, ligament, skin, vascular tissues, neural tissues, and skeletal muscle and as vehicle for the controlled delivery of drugs, proteins, and DNA. Various technologies come together to construct porous scaffolds to regenerate the tissues/organs and also for controlled and targeted release of bioactive agents in tissue engineering applications. In this paper, an overview of the different types of scaffolds with their material properties is discussed. The fabrication technologies for tissue engineering scaffolds, including the basic and conventional techniques to the more recent ones, are tabulated.

The effect of particle size reduction of the components of a common intumescent flame retardant system, consisting of pentaerythritol (PER) and ammonium polyphosphate (APP) in a weight ratio of 1 to 2, was investigated on the flammability and mechanical performance of flame retarded polypropylene (PP) compounds. Additives of reduced particle size were obtained by ball milling. In the case of PER, the significant reduction of particle size resulted in inferior flame retardant and mechanical performance, while the systems containing milled APP noticeably outperformed the reference intumescent system containing as-received additives. The beneficial effect of the particle size reduction of APP is explained by the better distribution of the particles in the polymer matrix and by the modified degradation mechanism which results in the formation of an effectively protecting carbonaceous foam accompanied with improved mechanical resistance. Nevertheless, 10% higher tensile strength was measured for the flame retarded PP compound when as-received APP was substituted by milled APP.

An accurate reaction model is required to analyze the characteristics of photopolymers. For this purpose, we propose a numerical model for radical photopolymerization. In the proposed model, elementary reactions such as initiation, propagation, and termination are considered, and we assume interdiffusion for each component in the material. We analyzed the diffraction characteristics of a radical photopolymer based on the proposed interdiffusion model with the beam propagation method. Moreover, we also performed hologram-recording experiments and evaluated the diffraction characteristics of the photopolymer medium. By comparing the numerical and experimental results, medium parameters such as reaction rate and diffusion coefficient can be estimated. We confirmed that the interdiffusion model can reproduce the experimental results and showed that the medium parameters affect the diffraction characteristics.

The objective of the present work was to study the incorporation of starch nanoparticles (SNP) produced by ultrasound in blends of poly(butylene adipate-co-terephthalate) (PBAT) and thermoplastic starch (TPS). The films were produced by extrusion using varying percentages of SNP (1, 2, 3, 4, and 5% w/w). The SNP were prepared in water without the addition of any chemical reagent. The results revealed that ultrasound treatment results in the formation of SNP less than 100 nm in size and of an amorphous character and lower thermal stability and low gelatinization temperature when compared with cassava starch. Scanning electron microscopy (SEM) showed that films presented some starch granules. The relative crystallinity (RC) of films decreases with increasing concentration of SNP. The addition of SNP slightly affected the thermal degradation of the films. The DSC results showed that the addition did not modify the interaction between the different components of the films. Mechanical tests revealed an increase in Young’s modulus (36%) and elongation-at-break (35%) with the incorporation of 1% SNP and this concentration reduced the water vapor permeability (53%) and significantly decreased the water absorption of the films, demonstrating that low concentrations of SNP can be used as reinforcement in a polymeric matrix.

Currently enhanced oil recovery (EOR) technology is getting more attention by many countries since energy crises are getting worse and frightening. Polymer flooding by hydrophobically associated polyacrylamides (HAPAM) and its modified silica nanocomposite are a widely implemented technique through enhanced oil recovery (EOR) technology. This polymers class can be synthesized by copolymerization of acrylamide (AM), reactive surfmer, functionalized silica nanoparticles, and a hydrophobic cross-linker moiety in the presence of water soluble initiator via heterogeneous emulsion polymerization technique, to form latexes that can be applied during polymer flooding. Chemical structure of the prepared copolymers was proven through different techniques such as Fourier transform infrared spectroscopy (FTIR), and nuclear magnetic spectroscopy (¹H&¹³C-NMR), and molecular weight was measured by gel permeation chromatography. Study of the effects of monomer, surfmer, cross-linker, silica, and initiator concentrations as well as reaction temperature was investigated to determine optimum polymerization conditions through single factor and orthogonal experiments. Evaluation of the prepared copolymers for enhancing recovered oil amount was evaluated by carrying out flooding experiments on one-dimensional sandstone model to determine recovery factor.

This study examined the degradation of polysaccharides to oligosaccharides in Chinese jujube fruits. Using a response surface model, the degradation conditions of polysaccharides under acid hydrolysis and enzymatic hydrolysis were optimized in laboratory conditions. A degradation rate of 66.9% was obtained under optimum acid hydrolysis conditions: 0.6 mol/L hydrochloric acid, 3% substrate concentration, and 1 h reaction time. A degradation rate of 41.4% was obtained under optimum enzyme hydrolysis conditions: 4.0 mL cellulose solution (10 mg/mL), 0.3 mL substrate solution (20 mg/mL), 0.7 mL citric acid buffer solution (pH 5), and 7.3 h reaction time. Using the stimulation effect for strain J-4 intestinal probiotic proliferation, the biological activity of oligosaccharides was determined. The results showed that the oligosaccharides from enzyme hydrolysis encouraged intestinal probiotic proliferation.

Blends based on high-density polyethylene (HDPE) and poly(lactic) acid (PLA) with different ratios of both polymers were produced: a blend with equal amounts of HDPE and PLA, hence 50 wt.% each, proved to be a useful compromise, allowing a high amount of bioderived charge without this being too detrimental for mechanical properties and considering its possibility to biodegradation behaviour in outdoor application. In this way, an optimal blend suitable for producing a composite with cellulosic fillers is proposed. In the selected polymer blend, wood flour (WF) was added as a natural filler in the proportion of 20, 30, and 40 wt.%, considering as 100 the weight of the polymer blend matrix. There are two compatibilizers to modify both HDPE-PLA blend and wood-flour/polymer interfaces, i.e., polyethylene-grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate. The most suitable percentage of compatibilizer for HDPE-PLA blends appears to be 3 wt.%, which was selected also for use with wood flour. In order to evaluate properties of blends and composites tensile tests, scanning electron microscopy, differential scanning calorimetry, thermogravimetric analyses, and infrared spectroscopy have been performed. Wood flour seems to affect heavy blend behaviour in process production of material suggesting that future studies are needed to reduce defectiveness.