Prediction of cutting force, tool wear and surface roughness of Al6061/SiC composite for end milling operations using RSM
Tóm tắt
Từ khóa
Tài liệu tham khảo
T. Ozben, E. Kilikap and O. Cakir, Investigation of mechanical and machinability properties of SiC particle reinforced Al-MMC, Journal of Materials Processing Technology, 198 (2008) 220–225..
N. S. Reddy, K. S. Shin and Y. Minyang, Experimental study of surface integrity during end milling of Al/SiC particulate metal-matrix composites, Journal of Materials Processing Technology, 201 (2008) 574–579.
A. Pramanik, L. C. Zhang and J. A. Arsecularatne, Prediction of cutting force in machining of metal matrix composites, International Journal of Machine Tools and Manufacture, 46 (2006) 1795–1803.
S. P. Dwivedi, S. Kumar and A. Kumar, Effect of turning parameters on surface roughness of A356/5% SiC composite produced by electromagnetic stir casting, Journal of Mechanical Science and Technology, 26(12) (2012) 3973–3979.
N. S. Reddy and P. Vengateshwararao, Selection of optimum tool geometry and cutting Conditions using a surface roughness prediction model for end milling, International Journal of Advanced Manufacturing Technology, 26 (2005) 1202–1210.
B.-C. Shin, S.-J. Ha, M.-W. Cho, T.-I. Seo, G.-S. Yoon and Y.-M. Heo, Indirect cutting force measurement in the micro end-milling process based on frequency analysis of sensor signals, Journal of Mechanical Science and Technology, 24 (2010) 165–168.
H. Chelladurai, V. K. Jain and N. S. Vyas, Development of a cutting tool condition monitoring system for high speed turning operation by vibration and strain analysis, International Journal of Advanced Manufacturing Technology, 37 (2008) 471–485.
S. Khamel, N. Ouelaa and K. Bouacha, Analysis and prediction of tool wear, surface roughness and cutting forces in hard turning with CBN tool, Journal of Mechanical Science and Technology, 26 (2012) 3605–3616.
M. Zatarain, I. Bediaga, J. Munoa and T. Insperger, Analysis of directional factors in milling: Importance of multi frequency calculation and of the inclusion of the effect of the helix angle, International Journal of Advanced Manufacturing Technology, 47 (2009) 535–542.
H. Aouici, M. A. Yallese, B. Fnides, K. Chaoui and T. Mabrouki, Modeling and optimization of hard turning of X38CrMoV5-1 steel with CBN tool:Machining parameters effects on flank wear and surface roughness, Journal of Mechanical Science and Technology, 25 (2011) 2843–2851.
J. Z. Zhang and J. C. Chen, Tool condition monitoring In an end milling operation based on the vibration signal collected through a micro controller — based data acquisition system, International Journal of Advanced Manufacturing Technology, 39 (2008) 118–128.
H. Nakagawa, Y. Kurita, K. Ogava, Y. Sugiyama and H. Hasigava, Experimental analysis of Chatter vibration in end milling using laser Doppler vibrometers, International Journal of Automation Technology, 2(6) (2008) 431–438.
P. S. Sivasakthivel, V. Velmurugan and R. Sudhakaran, Prediction of vibration amplitude for Machining parameters by response surface methodology in end milling, International Journal of Advanced Manufacturing Technology, 53 (2010) 456–461.
K. Palanikumar, Modeling and analysis for surface roughness in milling glassfiber reinforced plastics using response surface methodology, Materials Design, 28 (2007) 2611–2618.
N. Muthukrishnan and J. Paulo Davim, Optimization of machining parameters of Al/SiC — MMC with ANOVA and ANN analysis, Journal of Materials Processing Technology, 209 (2009) 225–232.
H. C. Anilkumar, H. S. Hebbar and K. S. Ravishankar, Mechanical properties of fly ash reinforced Aluminium alloy(Al6061) composites, International Journal of Mechanical and Materials Engineering, 6 (2011) 41–45.
M. N. Wahab, A. R. Daud and M. J. Ghazali, Preparation and characterization of stir cast Aluminium nitride reinforced aluminium metal matrix composites, International Journal of Mechanical and Materials Engineering, 4 (2009) 115–117.
D. C. Montgomery, Design and analysis of experiments, Wiley, New York (1976).