Effect of dielectric fluid with surfactant and graphite powder on Electrical Discharge Machining of titanium alloy using Taguchi method

Engineering Science and Technology, an International Journal - Tập 18 - Trang 524-535 - 2015
Murahari Kolli1, Adepu Kumar1
1Department of Mechanical Engineering, National Institute of Technology, Warangal, Telangana, India

Tài liệu tham khảo

Moiseyev, 2006

Liew, 2010

Rajurkar, 2011, Review of electrical discharge machining of titanium alloy, 10

Ezugwu, 1997, Titanium alloys and their machinability – a review, J. Mater. Process. Technol., 68, 262, 10.1016/S0924-0136(96)00030-1

Haron, 2005, The effect of machining on surface integrity of titanium alloy Ti–6Al–4V, J. Mater. Process. Technol., 166, 188, 10.1016/j.jmatprotec.2004.08.012

Dornfeld, 1999, Drilling burr formation in titanium alloy Ti–6Al–4V, Ann. CIRP, 48, 73, 10.1016/S0007-8506(07)63134-5

Endo, 2008, The effect of vibration on machining time and stability of discharge processing, 32, 269

Han-Ming, 2008, The use of SiC powder in water as dielectric for micro-slit EDM machining, J. Mater. Process. Technol., 195, 160, 10.1016/j.jmatprotec.2007.04.130

Kenneth, 2010

Churi, 2005, 885

Govindan, 2010

Abdulkareem, 2009, Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining, Int. J. Adv. Manuf. Technol., 45, 1146, 10.1007/s00170-009-2060-5

Jeswani, 1981, Effect of the addition of graphite powder to kerosene used as the dielectric fluid in electrical discharge machining, Wear, 70, 133, 10.1016/0043-1648(81)90148-4

Kibria, 2009, Comparative study of different dielectrics for micro-EDM performance during microhole machining of Ti–6Al–4V alloy, Int. J. Adv. Manuf. Technol., 48, 557

Murahari, 2014, Influence of span20 surfactant and graphite powder added in dielectric fluid on EDM of titanium alloy, J. Ind. Eng. Manag. Sci., 4, 62

Murahari, 2014, Effect of additives added in dielectric fluid on electrical discharge machining of titanium alloy, 52

Wu, 2009, Study on the characteristics of electrical discharge machining using dielectric with surfactant, J. Mater. Process. Technol., 209, 3783, 10.1016/j.jmatprotec.2008.09.005

Wu, 2005, Improvement of surface finish on SKD steel using electro-discharge machining with aluminum and surfactant added dielectric, Int. J. Mach. Tools Manuf., 45, 1195, 10.1016/j.ijmachtools.2004.12.005

Dukhin, 2004, 1

Zhang, 2012, Sinking EDM in water in oil emulsion, Int. J. Adv. Manuf. Technol.

Liu, 2010, Investigation of emulsion for die sinking EDM, Int. J. Adv. Manuf. Technol., 47, 403, 10.1007/s00170-009-2209-2

Konig, 1987, Aqueous solution of organic compounds as dielectric for EDM sinking, Ann. CIRP, 36, 10.1016/S0007-8506(07)62564-5

Nikalje, 2012, Analysis of recast layer and surface machined by electrical discharge machining

Zhang, 2012, Influence of dielectric type on porosity formation on electrical discharge machined surfaces, Metall. Mater. Trans. B, 43, 946, 10.1007/s11663-012-9653-3

Ross, 1998, 24

Montgomery, 1997, 395

Phadke Madhav, 1989, 41

Mohd Abbas, 2007, A review on current research trends in electrical discharge machining (EDM), Int. J. Mach. Tools Manuf., 47, 1214, 10.1016/j.ijmachtools.2006.08.026

Feng, 2003, Relative importance of electrostatic forces on powder particles, Powder Technol., 135, 65, 10.1016/j.powtec.2003.08.005

Masuzawa, 1983, Water based dielectric solution for EDM, Ann. CIRP, 32/1

Kansal, 2007, Technology and research developments in powder mixed electric discharge machining (PMEDM), J. Mater. Process. Technol., 184, 32, 10.1016/j.jmatprotec.2006.10.046

Yan, 2001, Surface modification of SKD61 during EDM with metal powder in dialectric, Mater. Trans., 42, 2597, 10.2320/matertrans.42.2597

Zhao, 2002, The application of research on powder mixed EDM in rough machining, J. Mater. Process. Technol., 129, 130, 10.1016/S0924-0136(02)00570-8

Rosen, 2004, 311

Shaw, 1992, 76

Erden, 1981, Thermo-mathematical modelling and optimization of energy pulse forms in electrical discharge machining, vol. 21(1), 11

Rehbein, 2004, Influence of selected groups of additives on breakdown in EDM sinking, J. Mater. Process. Technol., 149, 58, 10.1016/j.jmatprotec.2004.02.029

Hussain, 2012, Performance of electrical discharge machining using aluminium powder suspended distilled water, Turk. J. Eng. Environ. Sci., 36, 195

Wong, 1998, Near-mirror-finish phenomenon in EDM using powder-mixed dielectric, J. Mater. Process. Technol., 79, 30, 10.1016/S0924-0136(97)00450-0

Zhao, 2002, The application of research on powder mixed EDM in rough machining, J. Mater. Process. Technol., 129, 30, 10.1016/S0924-0136(02)00570-8

Okada, 2000, Formation of hard layer by EDM with carbon powder mixed fluid using titanium electrode, 464

Lee, 1988, Quantification of surface damage of tool steels after EDM, Int. J. Mach. Tools Manuf., 28, 359, 10.1016/0890-6955(88)90050-8

Thông tin
Thông tin xuất bản

Engineering Science and Technology, an International Journal

Tập 18

524-535

Thông tin tác giả