A review of mass transfer measurements using naphthalene sublimation

Kudchadker, 1978, Naphthalene

Dean, 1987, 1.308

Ambrose, 1975, The vapor pressure of naphthalene, J. Chem. Thermodynam., 7, 1173, 10.1016/0021-9614(75)90038-5

Sinke, 1974, A Method for Measurement of Vapor Pressures of Organic Compounds Below 0.1 Tort; Naphthalene as a Reference Substance, J. Chem. Thennodynam., 6, 311, 10.1016/0021-9614(74)90160-8

De Kruif, 1981, The Vapor Pressure of Solid and Liquid Naphthalene, J. Chem. Thermodynam., 13, 1081, 10.1016/0021-9614(81)90006-9

Thomas, 1916, The Evaporation of Naphthalene in Dry and in Moist Coal-Gas, J. Soc. Chem. Ind., 35, 506

Bradley, 1953, The Vapour Pressure and Lattice Energy of Some Aromatic Ring Compounds, J. Chem. Soc., Part II, 1690, 10.1039/jr9530001690

Sherwood, 1957, Mass Transfer Through Compressible Turbulent Boundary Layers, Can. J. Chem. Eng., 35, 51

Gil'denblat, 1960, Vapor Pressure over Crystalline Naphthalene, J. Appl. Chem. USSR, 33, 245

Fowler, 1968, Vapour Pressure of Naphthalene, J. Chem. Eng. Data, 13, 209, 10.1021/je60037a020

Macknick, 1979, Vapour Pressures of High-Molecular-Weight Hydrocarbons, J. Chem. Eng. Data, 24, 175, 10.1021/je60082a012

Van Ekeren, 1983, Vapor-Pressure Measurements on trans-Diphenylethene and Naphthalene Using a Spinning-Rotor Friction Gauge, J. Chem. Thermodynam., 15, 409, 10.1016/0021-9614(83)90038-1

Cho, 1989, Measurement of the Diffusion Coefficient of Naphthalene into Air

Chen, 1990

Mack, 1925, Average Cross-Sectional Areas of Molecules by Gaseous Diffusion Methods, J. Am. Chem. Soc., 47, 2468, 10.1021/ja01687a007

Caldwell, 1984, Diffusion Coefficient of Naphthalene in Air and Hydrogen, J. Chem. Eng. Data, 29, 60, 10.1021/je00035a020

Chapman, 1939, Mathematical Theory of Non-Uniform Gases, 252

Chen, 1962, New Generalized Equation for Gas Diffusion Coefficient, J. Chem. Eng. Data, 7, 37, 10.1021/je60012a011

Fuller, 1966, A New Method for Prediction of Binary Gas-Phase Diffusion Coefficients, Ind. Eng. Chem., 58, 19, 10.1021/ie50677a007

Sparrow, 1978, Heat Transfer and Pressure Drop for a Staggered Wall-Attached Array of Cylinders with Tip Clearance, Int. J. Heat Mass Transfer, 21, 1369, 10.1016/0017-9310(78)90200-4

Chen, 1992, The Effect of Fin Shapes on the Mass Transfer and Pressure Drop of the Staggered Array of Short Pin-Fins

Chyu, 1990, Heat Transfer and Pressure Drop for Short Pin-Fin Arrays with Pin-Endwall Fillet, J. Heat Transfer, 112, 926, 10.1115/1.2910502

Neal, 1970, The Development of a Technique for Applying Naphthalene to Surface for Mass Transfer Analogue Investigations, J. Phys. E. Sci. Instrum., 3, 636, 10.1088/0022-3735/3/8/312

Neal, 1975, The Development of the Thin-Film Naphthalene Mass-Transfer Analogue Technique for the Direct Measurement of Heat-Transfer Coefficients, Int. J. Heat Mass Transfer, 18, 559, 10.1016/0017-9310(75)90297-5

Lee, 1986, Heat Transfer and Pressure Drop Characteristics of an Array of Plates Aligned at Angles to the Flow in a Rectangular Duct, Int. J. Heat Mass Transfer, 29, 1553, 10.1016/0017-9310(86)90070-0

Lee, 1989, Heat Transfer and Pressure Drop Characteristics of an Assembly of Partially Segmented Plates, J. Heat Transfer, 111, 44, 10.1115/1.3250656

Cho, 1992, Heat/Mass Transfer Flow through an Array of Holes and Slits

Goldstein, 1985, Measurement of Local Mass Transfer on a Surface in the Region of the Base of a Protruding Cylinder with a Computer-Controlled Data Acquisition System, Int. J Heat Mass Transfer, 28, 977, 10.1016/0017-9310(85)90279-0

Hain, 1991, A Microcomputer-Controlled Data Acquisition System for Naphthalene Sublimation Measurement, 1

Eckert, 1976, Analogies to Heat Transfer Processes, 397

Wilkie, 1966, Fuel Element Heat Transfer near Dimple Braces, Nuc. Eng., 11, 596

Brakell, 1986, An Analysis of the Uniform Naphthalene Layer Mass Transfer Analogue Method Applied to Laminar Flow over a Flat Plate, 495

Behbahani, 1989, Measurement of the Local Mass Transfer Coefficient by Holographic Interferomery, HTD-112, 55

Eckert, 1972, Analysis of Heat and Mass Transfer, 373

Eckert, 1972, Analysis of Heat and Mass Transfer, 728

Simpson, 1972, A Note on the Turbulent Schmidt and Lewis Numbers in a Boundary Layer, Int. J. Heat Mass Transfer, 15, 177, 10.1016/0017-9310(72)90178-0

Chilton, 1934, Mass Transfer (Absorption) Coefficients, Ind. Eng. Chem., 26, 1183, 10.1021/ie50299a012

Lewis, 1971, A Heat/Mass Transfer Analogy Applied to Fully Developed Turbulent Flow in an Annulus, J. Mech. Eng. Sci., 13, 286, 10.1243/JMES_JOUR_1971_013_044_02

Von Karman, 1939, The Analogy Between Fluid Friction and Heat Transfer, Trans. ASME, 61, 705

Schultz-Grunow, 1940, Luftfahrtforschung, 17, 239

Kays, 1980, Convectioe Heat and Mass Transfer, 196

Petukhov, 1970, Heat Transfer and Friction in Turbulent Pipe Flow with Variable Physical Properties, Adv. Heat Transfer, 6, 503, 10.1016/S0065-2717(08)70153-9

Hartnett, 1957, Mass Transfer Cooling in a Laminar Boundary Layer with Constant Fluid Properties, Trans. ASME, 79, 247

Zukauskas, 1985

Zukauskas, 1972, Heat Transfer from Tubes in Crossflow, Adv. Heat Transfer, 8, 93, 10.1016/S0065-2717(08)70038-8

Goldstein, 1990, Convective Mass Transfer from a Square Cylinder and Its Base Plate, Int. J. Heat Mass Transfer, 33, 9, 10.1016/0017-9310(90)90136-I

Igarashi, 1983, Heat Transfer from a Square Prism to an Air Stream, Int. J. Heat Mass. Transfer, 28, 175, 10.1016/0017-9310(85)90019-5

Goldstein, 1984, The Effect of a Wall Boundary Layer on Local Mass Transfer from a Cylinder in Crossflow, J. Heat Transfer, 106, 260, 10.1115/1.3246667

Chen, 1992, Convective Transport Phenomena on the Suction Surface of a Turbine Blade Including the Influence of Secondary Flows near the Endwall, J. Turbomach., 114, 776, 10.1115/1.2928031

Sogin, 1958, Sublimation from Disks to Air Streams Flowing Normal to Their Surfaces, Trans. ASME, 80, 61

Sogin, 1991, An Improved Correlation of Stagnation Point Mass Transfer from Naphthalene Circular Disks Facing Uniform Airstreams, J. Heat Transfer, 113, 772, 10.1115/1.2910632

Sparrow, 1985, Local and Average Heat Transfer Characteristics for a Disk Situated Perpendicular to a Uniform Flow, J. Heat Transfer, 107, 321, 10.1115/1.3247417

Tien, 1978, Heat/Mass Transfer Characteristics and Fluid Flow Patterns for Airflow About an Inclined and Yawed Flat Plate

Sparrow, 1979, Effect of Finite Width on Heat Transfer and Fluid Flow About an Inclined Rectangular Plate, J. Heat Transfer, 101, 199, 10.1115/1.3450946

Sparrow, 1981, Heat Transfer from a Plate Elevated Above a Host Surface and Washed by a Separated Flow Induced by the Elevation Step, J. Heat Transfer, 103, 441, 10.1115/1.3244483

Sogin, 1961, Local Mass Transfer from Circular Cylinders in Cross Flow, J. Heat Transfer, 83, 483, 10.1115/1.3683672

Kestin, 1971, The Influence of Turbulence on Mass Transfer from Cylinders, J. Heat Transfer, 93, 321, 10.1115/1.3449823

Mayle, 1982, Spanwise Mass Transfer Variations on a Cylinder in Nominally Uniform Crossflow, 6, 135

Van Dresar, 1986, Convection at the Base of a Cylinder with a Horseshoe Vortex, 3, 1121

Sparrow, 1984, Heat Transfer Adjacent to the Attached End of a Cylinder in Cross Flow, Int. J. Heat Mass Transfer, 27, 233, 10.1016/0017-9310(84)90214-X

Kawamura, 1984, Heat Transfer from a Finite Circular Cylinder on the Flat Plate, Bull. JSME, 27, 2430, 10.1299/jsme1958.27.2430

Goldstein, 1990, Effect of Boundary Conditions Layer on Mass Transfer near the Base of a Cylinder in Crossflow, J. Heat Transfer, 112, 501, 10.1115/1.2910410

Yoo, 1993, Effects of Angle of Attack on Mass Transfer from a Square Cylinder and Its Base Plate, Int. J. Heat Mass Transfer, 36, 371, 10.1016/0017-9310(93)80013-K

Cho, 1994, Mass Transfer with Flow Through an Array of Rectangular Cylinders, J. Heat Transfer, 116, 904, 10.1115/1.2911465

Christian, 1957, Experimental Investigation of Mass Transfer by Sublimation from Sharp-Edged Cylinders in Axisymmetric Flow with Laminar Boundary Layer, 359

Lee, 1968, Transport Processes in Flow Around a Sphere with Particular Reference to the Transfer of Mass, Int. J. Heat Mass Tranfer, 11, 1013, 10.1016/0017-9310(68)90007-0

Sparrow, 1983, Heat Transfer Coefficients and Patterns of Fluid Flow for Contacting Spheres at Various Angles of Attack, J. Heat Transfer, 105, 48, 10.1115/1.3245558

Saboja, 1974, Local and Average Transfer Coefficients for One-Row Plate Fin and Tube Heat Exchanger Configurations, J. Heat Transfer, 96, 265, 10.1115/1.3450189

Ruiz, 1981, Effect of Blockage-Induced Flow Maldistribution on the Heat Transfer and Pressure Drop in a Tube Bank

Berman, 1983, Effect of Upstream Bands on Heat Transfer and Pressure Drop in a Tube Bank

Chyu, 1992, Influences of a Cylinder Array on the Mass Transfer from a Flat Surface, Int. J. Heat Mass Transfer, 34, 2175, 10.1016/0017-9310(91)90044-F

Xiao, 1992, Experimental Study on Effect of Interwall Tube Cylinder on Heat/Mass Transfer Characteristics of Corrugated Plate Fin-and-Tube Exchanger Configuration, J. Heat Transfer, 114, 755, 10.1115/1.2911345

Owen, 1967, Heat Transfer from Plain and Finned Cylinders in Crossflow, J. Inst. Heat. Vent. Eng., 35, 213

Chastain, 1983, Sensitivity of the Heat Transfer Coefficient on an Annular Fin to Small Angles of Attack

Sparrow, 1985, Longitudinally-Finned CrossFlow Tube Banks and Their Heat Transfer and Pressure Drop Characteristics, Int. J. Heat Mass Transfer, 28, 339, 10.1016/0017-9310(85)90067-5

Merker, 1986, Heat Transfer and Pressure Drop on the Shell-Side of Tube-Banks Having Oval-Shaped Tubes, Int. J. Heat Mass Transer, 29, 1903, 10.1016/0017-9310(86)90008-6

Cur, 1982, Local Turbulent Heat Transfer Coefficients in a Symmetrically or Asymmetrically Heated Flat Rectangular Duct with Either Uniform or Nonuniform Inlet Velocity

Sparrow, 1980, Measurements of Heat Transfer and Pressure Drop for an Array of Staggered Plates Aligned Parallel to an Air Flow, J. Heat Transfer, 102, 426, 10.1115/1.3244317

Sogin, 1960, Laminar Transfer from Isothermal Spanwise Strips on a Flat Plate, J. Heat Transfer, 82, 53, 10.1115/1.3679879

Sogin, 1963, Turbulent Heat Transfer from Isothermal Spanwise Strips on a Flat Plate, 447

Sherwood, 1960, Sublimation Mass Transfer Through Compressible Boundary Layers on a Flat Plate, J. Heat Transfer, 82, 313, 10.1115/1.3679941

Sparrow, 1982, Turbulent Heat Transfer in a Symmetrically or Asymmetrically Heated Flat Rectangular Duct with Flow Separation at Inlet, J. Heat Transfer, 104, 82, 10.1115/1.3245072

Molki, 1982, Turbulent Tube-Flow Heat Transfer Coefficients in the Presence of Flow Imbalance in the Tubes of a Parallel Array

Sparrow, 1987, Turbulent Duct Flow with Streamwise Nonuniform Heating at the Duct Wall, Int. J. Heat Mass Transfer, 30, 175, 10.1016/0017-9310(87)90070-6

Kumori, 1980, Characteristics of Fully Developed Turbulent Flow and Mass Transfer in a Square Duct, Int. Chem. Eng., 20, 219

Goldstein, 1992, The Near-Corner Mass Transfer Associated with Turbulent Flow in a Square Duct, Warme- and Stoffubertragung., 27, 265, 10.1007/BF01589925

Burns, 1991, Local Mass Transfer in Turbulent Flow Downstream of a 90° Bend in a Duct of Square Cross Section

Chandra, 1987, Effect on Rib Angle on Local Heat/Mass Transfer Distribution in a Two-Pass Rib-Roughened Channel, ASME Paper 87-GT-94

Han, 1988, Local Heat/Mass Transfer Distributions Around Sharp 180 deg. Turns in TwoPass Smooth and Rib-Roughened Channels, J. Heat Transfer, 110, 91, 10.1115/1.3250478

Chandra, 1989, Pressure Drop and Mass Transfer in Two-Pass Ribbed Channels, J. Thermophys., 3, 315, 10.2514/3.28787

Sparrow, 1984, Symmetric vs. Asymmetric Periodic Disturbances at the Walls of a Heated Flow Passage, Int. J. Heat Mass Transfer, 27, 2133, 10.1016/0017-9310(84)90200-X

Souza Mendes, 1984, Periodically Converging-Diverging Tubes and Their Turbulent Heat Transfer, Pressure Drop, Fluid Flow, and Enhancement Characteristics, J. Heat Transfer, 106, 55, 10.1115/1.3246659

Molki, 1986, Effect of Interwall Spacing on Heat Transfer and Pressure Drop in a Corrugated-Wall Duct, Int. J. Heat Mass Transfer, 29, 987, 10.1016/0017-9310(86)90198-5

Niethammer, 1982, Heat Transfer and Pressure Drop Characteristics for Airflow over Arrays of Rectangular Modules

Sparrow, 1983, Enhanced and Local Heat Transfer, Pressure Drop, and Flow Visualization for Arrays of Block-like Electronic Components, Int. J. Heat Mass Transfer, 26, 689, 10.1016/0017-9310(83)90019-4

Otis, 1984, Heat Transfer at the Smooth and the BlockCovered Walls of a Flat Rectangular Duct

Souza Mendes, 1987, Heat Transfer and Pressure Drop Experiments in Air-Cooled Electronic-Component Arrays, J. Thermophys. Heat Transfer, 1, 373, 10.2514/3.54

Chyu, 1989, Heat Transfer in the Tip Region of Grooved Turbine Blades, J. Turbomach., 111, 131, 10.1115/1.3262247

Sparrow, 1986, Mass Transfer at the Base of a Cylindrical Cavity Recessed in the Floor of a Flat Duct, J. Heat Transfer, 108, 853, 10.1115/1.3247023

Chyu, 1986, Local Mass Transfer in Rectangular Cavities with Separated Turbulent Flow, 3, 1065

Achenbach, 1990, Mass Transfer Downstream of a Backward or a Forward-Facing Step, 16-TR-4, 305

Baskakov, 1972, The Determination of the Convective Component of the Coefficient of Heat Transfer to a Gas in a Fluidized Bed, Int. Chem. Eng., 12, 53

Gurdal, 1980, Heat Transfer at an Upstream-Facing Surface Washed by Fluid en route to an Aperture in the Surface

Ortiz, 1981, Heat Transfer Coefficients for the Upstream Face of a Perforated Plate Positioned Normal to an Oncoming Flow

Sparrow, 1975, Impingement Transfer Coefficients due to Initially Laminar Slot Jets, Int. J. Heat Mass Transfer, 18, 597, 10.1016/0017-9310(75)90271-9

Koopman, 1976, Local and Average Transfer Coefficients due to an Impinging Row of Jets, Int. J. Heat Mass Transfer, 19, 673, 10.1016/0017-9310(76)90051-X

Sparrow, 1980, Heat Transfer Characteristics of an Obliquely Impinging Circular Jet, J. Heat Transfer, 102, 202, 10.1115/1.3244261

Ward, 1982, Heat Transfer from a Turbulent, Swirling, Impinging Jet, 3, 401

Popiel, 1986, Mass or Heat Transfer in Impinging Single, Round Jets Emitted by a Bell-Shaped Nozzle and Sharp-Ended Orifice, 3, 1187

Pagenkopf, 1992, Local and Average Transfer Coefficients due to Different Impingement Arrangement for Blade Cooling Application

Sparrow, 1984, Jet Impingement Heat Transfer for a Circular Jet Impinging in Crossflow on a Cylinder, J. Heat Transfer, 106, 570, 10.1115/1.3246717

Santoro, 1988, Experiments for the Determination of Convective Diffusion Heat/Mass Transfer to Burner Rig Test Targets Comparable in Size to Jet Stream Diameter, J. Heat Transfer, 110, 442, 10.1115/1.3250505

Gokoglu, 1988, Determination of Convective Diffusion Heat/Mass Transfer Rates to Burner Rig Test Targets Comparable in Size to Cross-Stream Jet Diameter, J. Heat Transfer, 110, 449, 10.1115/1.3250506

Chong, 1986, An Experimental Study of Two-Dimensional Jet-Impingement Heat/Mass Transfer in a Confined Cross-Flow, 3, 1225

Goldstein, 1982, Mass Transfer in the Neighborhood of Jets Entering a Crossflow, J. Heat Transfer, 104, 715, 10.1115/1.3245190

Webster, 1987, Measurements of Mass Transfer Coefficient and Effectiveness in the Recovery Region of a Film-Cooled Surface, Int. J. Heat Mass Transfer, 30, 781, 10.1016/0017-9310(87)90208-0

Kumada, 1981, Studies of Full-Coverage Film Cooling. Part 2: Measurement of Local Heat Transfer Coefficient, ASME Paper 81-GT-38

Karni, 1990, Surface Injection Effect on Mass Transfer from a Cylinder in Crossflow: A Simulation of Film Cooling in the Leading Edge Region of a Turbine Blade, J. Turbomach., 112, 418, 10.1115/1.2927676

Lee, 1992, Effect of Injection Hole Position and Blowing Rate on Mass Transfer About a Film-Cooled Cylinder, Vol. 1, 363

Cho, 1993, Heat (Mass) Transfer and Film Cooling Efectiveness with Injection Through Discrete Holes. Part 1: Within Holes and on the Back Surface, ASME Paper 93-WA/HT-58

Cho, 1995, Heat (Mass) Transfer and Film Cooling Efectiveness with Injection Through Discrete Holes. Part 1: Within Holes and on the Back Surface, J. Turbomach.

Cho, 1993, Heat (Mass) Transfer and Film Cooling Effectiveness with Injection Through Discrete Holes. Part 11: On the Exposed Surface, ASME Paper 93WA/HT-59

Cho, 1995, Heat (Mass) Transfer and Film Cooling Effectiveness with Injection Through Discrete Holes. Part 11: On the Exposed Surface, J. Turbomach

Goldstein, 1988, Turbulent Transport on the Endwall in the Region Between Adjacent Turbine Blades, J. Heat Transfer, 110, 862, 10.1115/1.3250586

Chen, 1988, Convectioe Transport Phenomena on a Turbine Balde

Kreith, 1959, Heat and Mass Transfer from a Rotating Disk, J. Heat Transfer, 81, 95, 10.1115/1.4008145

Koyama, 1981, Mass Transfer from a Rotating Inclined Plate, J. Heat Transfer, 103, 204, 10.1115/1.3244442

Sparrow, 1982, Heat Transfer Coefficients for a Cup-like Cavity Rotating About Its Own Axis, Int. J. Heat Mass Transfer, 25, 1333, 10.1016/0017-9310(82)90127-2

Sparrow, 1986, Heat Transfer from Rotating Annular Fins, Int. J. Heat Mass Transfer, 29, 831, 10.1016/0017-9310(86)90179-1

Sparrow, 1987, Heat and Mass Transfer Adjacent to the Free End of a Rotating Cylinder, Int. J. Heat Mass Transfer, 30, 807, 10.1016/0017-9310(87)90211-0

Lee, 1989, Heat Transfer Charcteristics of the Annulus of Two-Coaxial Cylinders with One Cylinder Rotating, Int. J. Heat Mass Transfer, 32, 711, 10.1016/0017-9310(89)90218-4

Goldstein, 1973, Natural Convection Mass Transfer Adjacent to Horizontal Plates, Int. J. Heat Mass Transfer, 16, 1025, 10.1016/0017-9310(73)90041-0

Bandrowski, 1976, Free Convection Mass Transfer from Horizontal Plates, Int. J. Heat Mass Transfer, 19, 827, 10.1016/0017-9310(76)90195-2

Sparrow, 1979, Natural Convection in a Ternary Gas Mixture-Application to the Naphthalene Sublimation Technique, J. Heat Transfer, 101, 404, 10.1115/1.3450988

Sparrow, 1980, Experiments on Natural Convection Heat Transfer on the Fins of a Finned Horizontal Tube, Int. J. Heat Mass Transfer, 23, 1555, 10.1016/0017-9310(80)90159-3

Goldstein, 1983, Laminar Natural Convection from a Horizontal Plate and the Influence of Plate-Edge Extensions, J. Fluid Mech., 129, 55, 10.1017/S0022112083000646

Souza Mendes, 1991, The Naphthalene Sublimation Technique, Exp. Thermal Fluid Sci., 4, 510, 10.1016/0894-1777(91)90031-L

Kline, 1953, Describing Uncertainty in Single-Sample Experiments, Mech. Eng., 75, 3