Các bài báo tiêu biểu
Thin films of manganese-doped cadmium oxide (CdO:Mn) with different Mn-doping levels (0, 1, 2, 3 and 4 at.%) were deposited on glass substrates by employing an inexpensive, simplified spray technique using a perfume atomizer at 375 °C. The influence of Mn incorporation on the structural, morphological, optical and electrical properties of CdO films has been studied. All the films exhibit cubic crystal structure with a (1 1 1) preferential orientation. Mn-doping causes a slight shift of the (1 1 1) diffraction peak towards higher angle. The crystallite size of the films is found to decrease from 34.63 nm to 17.68 nm with an increase in Mn doping concentration. The CdO:Mn film coated with 1 at.% Mn exhibit a high transparency of nearly 90 % which decreases for higher doping concentration. The optical band gap decreases with an increase in Mn doping concentration. All the films have electrical resistivity of the order of 10−4 Ω·cm.
Thin films of lead oxide were synthesized by cost effective spray pyrolysis technique at different substrate temperatures on glass substrates. Effect of substrate temperature on the growth mechanism and physical properties of the films was investigated. All the films were polycrystalline in nature with tetragonal structure corresponding to α-PbO. The films coated at 225 °C and 275 °C were (1 0 1) oriented, while the films deposited at 325 °C and 375 °C were (0 0 2) oriented. Above 375 °C, the pure tetragonal nature deteriorated and the peaks corresponding to orthorhombic phase were observed. The band gap value was found to be in the range of 2.3 to 2.62 eV. All the films had a resistivity of the order of 103 ohm-cm. A minimum resistivity of 0.0191 × 103 ohm-cm was obtained for the film coated at 325 °C. The activation energy increased with increase in substrate temperature.
Poly(N-isopropylacrylamide-co-methacrylic acid) microgels [p(NIPAM-co-MAAc)] were synthesized by precipitation polymerization of N-isopropylacrylamide and methacrylic acid in aqueous medium. These microgels were characterized by dynamic light scattering and Fourier transform infrared spectroscopy. These microgels were used as micro-reactors for in situ synthesis of copper nanoparticles using sodium borohydride (NaBH4) as reducing agent. The hybrid microgels were used as catalysts for the reduction of nitrobenzene in aqueous media. The reaction was performed with different concentrations of catalyst and reducing agent. A linear relationship was found between apparent rate constant (kapp) and amount of catalyst. When the amount of catalyst was increased from 0.13 to 0.76 mg/mL then kapp was increased from 0.03 to 0.14 min-1. Activation parameters were also determined by performing reaction at two different temperatures. The catalytic process has been discussed in terms of energy of activation, enthalpy of activation and entropy of activation. The synthesized particles were found to be stable even after 14 weeks and showed catalytic activity for the reduction of nitrobenzene.
Wrinkled graphene, derived from a facile thermal decomposition and chemical method, was subjected to various analysis techniques and the results have been reported here. Raman studies revealed the presence of highly graphitized amorphous carbon, which was evident by the appearance of five peaks in the deconvoluted first order spectrum. This result was very well corroborated by the XRD analysis. XPS and FT-IR spectra confirmed the incorporation of oxygen functionalities into the carbon backbone. AFM and SEM images of the sample disclosed a cluster of few-layer wrinkled graphene fragments. TEM images displayed a chain of nearly spherical aggregates of graphene, resembling nanohorns. The resistivity and sheet resistance of the sample were found to be low, making the obtained material a promising candidate for various device applications. Hence, kerosene soot proved to be an efficient precursor for facile synthesis of few layer graphene-like nanocarbon.
Multi-walled carbon nanotubes have been synthesized at different temperatures ranging from 550 °C to 750 °C on silica supported Fe-Mo catalyst by chemical vapour deposition technique using Cymbopogen flexuous oil under nitrogen atmosphere. The as-grown MWNTs were characterized by scanning electron microscope (SEM), high resolution transmission electron microscope (HRTEM), X-ray diffraction analysis (XRD) and Raman spectral studies. The HRTEM and Raman spectroscopic studies confirmed the evolution of MWNTs with the outer diameter between 20 and 40 nm. The possibility of using as-grown MWNTs as an adsorbent for removal of As (V) ions from drinking water was studied. Adsorption isotherm data were interpreted by the Langmuir and Freundlich equations. Kinetic data were studied using Elovich, pseudo-first order and pseudo-second order equations in order to elucidate the reaction mechanism.
This report concerns the properties of an interface formed between Pd films deposited onto the surface of (0001)-oriented n-type GaN at room temperature (RT) under ultrahigh vacuum. The surface of clean substrate and the stages of Pd-film growth were characterized in situ by X-ray photoelectron spectroscopy (XPS), scanning tunneling microscopy (STM), ultraviolet photoelectron spectroscopy (UPS), and low energy electron diffraction (LEED).
As-deposited Pd films are grainy, cover the substrate surface uniformly and reproduce its topography. Electron affinity of the clean n-GaN surface amounts to 3.1 eV. The work function of the Pd-film is equal to 5.3 eV. No chemical interaction has been found at the Pd/GaN interface formed at RT. The Schottky barrier height of the Pd/GaN contact is equal to 1.60 eV.
First-principles calculations of the lattice constants, bulk modulus, pressure derivatives of the bulk modulus and elastic constants of AlN and TiN compounds in rock-salt (B1) and wurtzite (B4) structures are presented. We have used the fullpotential linearized augmented plane wave (FP-LAPW) method within the density functional theory (DFT) in the generalized gradient approximation (GGA) for the exchange-correlation functional. Moreover, the elastic properties of cubic TiN and hexagonal AlN, including elastic constants, bulk and shear moduli are determined and compared with previous experimental and theoretical data. Our results show that the structural transition at 0 K from wurtzite to rock-salt phase occurs at 10 GPa and −26 GPa for AlN and TiN, respectively. These results are consistent with those of other studies found in the literature.
Aluminosilicate materials were obtained by sol-gel method, using different Al2O3 and SiO2 precursors in order to prepare sols based on water and organic solvents. As SiO2 precursors, Aerosil 200TM and tetraethoxysilane TEOS: Si(OC2H5)4 were applied, while DisperalTM and aluminium secondary butoxide ATSB: Al(OC4H9)3 were used for Al2O3 ones. Bulk samples were obtained by heating gels at 500 °C, 850 °C and at 1150 °C in air, while thin films were synthesized on carbon, steel and alundum (representing porous ceramics) substrates by the dip coating method. Thin films were annealed in air (steel and alundum) and in argon (carbon) at different temperatures, depending on the substrate type. The samples were synthesized as gels and coatings of the composition corresponding the that of 3Al2O3·2SiO2 mullite because of the specific valuable properties of this material. The structure of the annealed bulk samples and coatings was studied by FT-IR spectroscopy and XRD method (in standard and GID configurations). Additionally, the electron microscopy (SEM) together with EDS microanalysis were applied to describe the morphology and the chemical composition of thin films. The analysis of FT-IR spectra and X-ray diffraction patterns of bulk samples revealed the presence of γ-Al2O3 and δ-Al2O3 phases, together with the small amount of SiO2 in the particulate samples. This observation was confirmed by the bands due to vibrations of Al–O bonds occurring in γ-Al2O3 and δ-Al2O3 structures, in the range of 400 to 900 cm−1. The same phases (γ-Al2O3 and δ-Al2O) were observed in the deposited coatings, but the presence of particulate ones strongly depended on the type of Al2O3 and SiO2 precursor and on the heat treatment temperature. All thin films contained considerable amounts of amorphous phase.
A new route of emulsifier-free emulsion polymerization based on the homogenous mechanism was investigated to prepare magnetic nanoparticles coated by poly (methyl methacrylate) (PMMA). The experimental results confirm the formation of PMMA thin and unique layers covering magnetite cores. The polymer layer thickness, determined from transmission electron microscopy (TEM) images, increases from 4.3 nm to 6.8 nm with increasing mass ratio of MMA to magnetite from 3:1 to 11:1. The increase of the polymer thickness results in the decrease in magnetization saturation of polymeric coated magnetic particles. However, this reduction, no more than 13 emu g−1, is much lower compared to that in other studies with the presence of surfactants or emulsifiers. Besides, the dispersion stability of the prepared particles is significantly improved.
The thermal evolution of the interface formed by room temperature (RT) deposition of Ni atoms (coverage 0.1, 0.5, 1.2 ML) onto a Ge(111)-c(2 × 8) surface has been studied with the use of scanning tunneling microscopy (STM). Atomically resolved STM images revealed that, at RT, the boundaries between the different c(2 × 8) domains acted as nucleation sites for Ni atoms. After annealing the surface with deposited material at 473 to 673 K the formation of nano-sized islands of NixGey compounds was observed. In addition, the occurrence of ring-like structures was recorded. Based on the dual-polarity images the latter were assigned to Ni atoms adsorbed on Ge adatoms.