Measurement and Control

The assist-as-needed technique in robotic rehabilitation is a popular technique that encourages patients’ active participation to promote motor recovery. It has been proven beneficial for patients with functional motor disability. However, its application in robotic therapy has been hindered by a poor estimation method of subjects’ functional or movement ability which is required for setting the appropriate robotic assistance. Moreover, there is also the need for consistency and repeatability of the functional ability estimation in line with the clinical procedure to facilitate a wider clinical adoption. In this study, we propose a new technique of estimation of subject’s functional ability based on the Wolf Motor Function Test. We called this estimation the functional ability index. The functional ability index enables the modulation of robotic assistance and gives a more consistent indication of subjects’ upper-limb movement ability during therapy session. Our baseline controller is an adaptive inertia-related controller, which is integrated with the functional ability index algorithm to provide movement assistance as when needed. Experimental studies are conducted on three hemiplegic patients with different levels of upper-limb impairments. Each patient is requested to perform reaching task of lifting a can from table-to-mouth according to the guidelines stipulated in the Wolf Motor Function Test. Data were collected using two inertial measurement unit sensors installed at the flexion/extension joints, and the functional ability score of each patient was rated by an experienced therapist. Results showed that the proposed functional ability index algorithm can estimate patients’ functional ability level consistently with clinical procedure and can modify generated robotic assistance in accordance with patients’ functional movement ability.

The presence of outliers is the main reason leading to ineffectiveness of advanced data-driven control methods in electric arc furnace systems. This paper proposes a hybrid method dedicated to detecting outliers in electric arc furnace systems, where process data are characterized as unlabeled, imbalanced, non-stationary and noisy. First, the raw data are divided into certain number of clusters. Then, with each cluster, a one-class classifier can be trained. So with these well-trained sub-models, new test points can be investigated. Those points that are rejected by all sub-models will be labeled as outliers. With the combination of one-class classification and clustering technique, the intricate data in electric arc furnace can be processed effectively. In addition, the detector will be updated with a specific strategy to enhance its adaptiveness. A series of experiments are carried out, and comparative results have shown the effectiveness of our method.

The case is made for wider implementation of the European Community absorbance method for measuring colour in raw and potable water. Colour measurement techniques and the difficulties associated with them are examined. A simple graphical method for converting non-standard wavelength absorbance records to the EC 400 nm standard is outlined.

In this paper, a novel backstepping terminal super-twisting sliding mode (TSTSM) with high order sliding mode observer (HOSMO) is proposed to control the two degrees of freedom (DOFs) Serial Elastic Actuator (SEA), inspired by a lower limb of humanoid robots. First, the dynamic model, extended from our previous study, is presented for developing the control algorithm. Secondly, the backstepping technique is utilized to separate the overall system into two subsystems. One of the challenges of SEA is to deal with the evident oscillations caused by the elastic element, which might lead to the degrading performance of load position control. In order to reduce this adverse effect, a TSTSM is proposed to control the position tracking of two subsystems. The advantages of TSTSM are the finite-time convergence despite the bounded perturbation and the dramatic reduction of the chattering phenomenon. To construct and implement the TSTSM controller, it requires the knowledge of all states, which is not available in the current lower limb system setup. Therefore, a HOSMO is utilized to estimate the unknown states. Finally, experiment results are carried out to assess the effectiveness of the proposed controller and compare it with those of different control schemes.

In this paper, a novel backstepping terminal super-twisting sliding mode (TSTSM) with high order sliding mode observer (HOSMO) is proposed to control the two degrees of freedom (DOFs) Serial Elastic Actuator (SEA), inspired by a lower limb of humanoid robots. First, the dynamic model, extended from our previous study, is presented for developing the control algorithm. Secondly, the backstepping technique is utilized to separate the overall system into two subsystems. One of the challenges of SEA is to deal with the evident oscillations caused by the elastic element, which might lead to the degrading performance of load position control. In order to reduce this adverse effect, a TSTSM is proposed to control the position tracking of two subsystems. The advantages of TSTSM are the finite-time convergence despite the bounded perturbation and the dramatic reduction of the chattering phenomenon. To construct and implement the TSTSM controller, it requires the knowledge of all states, which is not available in the current lower limb system setup. Therefore, a HOSMO is utilized to estimate the unknown states. Finally, experiment results are carried out to assess the effectiveness of the proposed controller and compare it with those of different control schemes.