Archives of Metallurgy and Materials
SCIE-ISI SCOPUS (2002,2004-2024)
1733-3490
2300-1909
Ba Lan
Cơ quản chủ quản: POLSKA AKAD NAUK, POLISH ACAD SCIENCES, INST METALL & MATER SCI PAS , Polish Academy of Sciences, Institute of Metallurgy and Materials Science
Lĩnh vực:
Metals and Alloys
Phân tích ảnh hưởng
Các bài báo tiêu biểu
Quasi-Static and Dynamic Tensile Properties of Ti-6Al-4V Alloy
Tập 58 Số 4 - Trang 1261-1265 - 2013
Abstract Ti-6Al-4V alloy is widely used, mainly in aircraft industry, due to its
low density, excellent corrosion/oxidation resistance and attractive mechanical
properties. This alloy has relatively low formability, so forming parts of
complex geometries out of this alloy requires precisely controlled
thermomechanical processing parameters. In industrial conditions Ti-6Al-4V alloy
is usually proce...
Recent Developments on Discontinuous Precipitation
Tập 62 Số 2 - Trang 955-968 - 2017
AbstractThe discontinuous precipitation (DP) belongs to a group of diffusive
solid state phase transformations during which the formation of a new phase is
heterogeneous and limited to a migrating reaction front (RF). The use of
analytical electron microscopy provided reliable information that there is no
differences in the diffusion rate at the stationary grain boundary and moving RF
of DP reacti...
The Characterization Of Cast Fe-Cr-C Alloy
Tập 60 Số 2 - Trang 779-782 - 2015
AbstractThe paper presents the results of the characterization of alloy from
Fe-Cr-C (carbon content 0.79 wt.%) system including the microstructure, phase
analysis, morphology and hardness in as cast state. The chemical composition was
designed to create chromium-rich ferritic matrix with high volume fraction of
carbides in form of interdendritic eutectics. The research was carried out on
the cros...
Influence of the Quenching Rate on the Structure and Magnetic Properties of the Fe-Based Amorphous Alloy
Tập 61 Số 1 - Trang 439-444 - 2016
This paper presents the results of investigations into the structure,
microstructure and magnetic properties of Fe61Co10Y8W1B20 amorphous alloy. The
alloy samples were in two physical forms: (1) plates of approximate thickness
0.5 mm (so-called bulk amorphous alloys) and (2) a ribbon of approximate
thickness 35 μm (so-called classic amorphous alloy). The investigations
comprised: X-ray diffractome...
Microgravimetric Studies of Selenium Electrodeposition Onto Different Substrates
Tập 59 Số 3 - Trang 871-877 - 2014
Abstract The mechanism of selenium electrodeposition from sulfuric acid solution
on different substrates was studied with the electrochemical techniques. The
cyclic voltammetry was combined with the quartz crystal microbalance technique
to analyze selenium deposition process. The electrochemical reduction of
selenous acid on gold, silver and copper electrodes was investigated. It was
found that re...
Modeling of the Thermodynamic Properties of Liquid Fe-Ni and Fe-Co Alloys From the Surface Tension Data
Tập 56 Số 1 - Trang 13-23 - 2011
Modeling of the Thermodynamic Properties of Liquid Fe-Ni and Fe-Co Alloys From
the Surface Tension DataRecently proposed method of modeling of thermodynamic
properties of liquid binary alloys from their surface tension data is described.
The method utilizes Melford and Hoar equation, relating surface tension with
excess Gibbs free energy, combined with new description of the monatomic surface
laye...
Effect of Welding Thermal Cycles on Microstructure and Mechanical Properties of Simulated Heat Affected Zone for a Weldox 1300 Ultra-High Strength Alloy Steel
Tập 61 Số 1 - Trang 127-132 - 2016
In the present study, the investigation of weldability of ultra-high strength
steel has been presented. The thermal simulated samples were used to investigate
the effect of welding cooling time t8/5 on microstructure and mechanical
properties of heat affected zone (HAZ) for a Weldox 1300 ultra-high strength
steel. In the frame of these investigation the microstructure was studied by
light and tran...
Manufacturing of Porous Al-Cr Preforms for Composite Reinforcing Using Microwave Activated Combustion Synthesis
Tập 59 Số 3 - Trang 1125-1127 - 2014
Abstract The combustion synthesis of porous skeletons (preforms) of
intermetallic Al–Cr compounds intended for metal matrix composite MMC
reinforcing was developed. Mixture of Al and Cr powders with granularity of −10,
−44, −74mm were cold isostatic pressed and next ignited and synthetized in a
microwave reactor under argon atmosphere (microwave-activated combustion
synthesis MACS). In order to ig...
The Influence of Mo Content on Phase Transformation in Ti-Mo Alloys
Tập 62 Số 4 - Trang 2051-2056 - 2017
AbstractTitaniumβ-type alloys are a class of interesting biomaterials that can
exhibit a unique combination of mechanical as well as physicochemical and
biological properties. The aim of this study is to develop a titanium-molybdenum
alloys (Ti-x at % Mo,x= 15 and 23). These materials were prepared by the
combination of mechanical alloying and powder metallurgical process. The details
of the proce...