Virtual crack closure technique: History, approach, and applications
Tóm tắt
An overview of the virtual crack closure technique is presented. The approach used is discussed, the history summarized, and insight into its applications provided. Equations for two-dimensional quadrilateral finite elements with linear and quadratic shape functions are given. Formulas for applying the technique in conjunction with three-dimensional solid elements as well as plate/shell elements are also provided. Necessary modifications for the use of the method with geometrically nonlinear finite element analysis and corrections required for elements at the crack tip with different lengths and widths are discussed. The problems associated with cracks or delaminations propagating between different materials are mentioned briefly, as well as a strategy to minimize these problems. Due to an increased interest in using a fracture mechanics–based approach to assess the damage tolerance of composite structures in the design phase and during certification, the engineering problems selected as examples and given as references focus on the application of the technique to components made of composite materials.
Từ khóa
Tài liệu tham khảo
Garg AC (1988), Delamination—A damage mode in composite structures, Eng. Fract. Mech. 29(5), 557–584.
Bolotin VV (1996), Delaminations in composite structures: its origin, buckling, growth and stability, Composites, Part B 27B(2), 129–145.
Pagano NJ and Schoeppner, GA (2000), Delamination of polymer matrix composites: Problems and assessment, Comprehensive Composite Materials, A Kelly and C Zweben (eds), Elsevier Science, Vol 2, 433–528.
Tay TE (2003), Characterization and analysis of delamination fracture in composites: An overview of developments from 1990 to 2001, Appl. Mech. Rev. 56(1), 1–32.
O’Brien TK (1982), Characterization of delamination onset and growth in a composite laminate, pp. 140–167, Damage in Composite Materials, ASTM STP 775, Am Soc for Testing and Materials, Philadelphia, PA.
O’Brien TK (1998), Interlaminar fracture toughness: The long and winding road to standardization, Composites, Part B 29(1), 57–62.
Martin RH (1998), Incorporating interlaminar fracture mechanics into design, pp. 83–92, Int Conf on Designing Cost-Effective Composites, IMechE Conference Transactions, London, U.K.
O’Brien TK and Martin RH (1993), Round robin testing for mode I interlaminar fracture toughness of composite materials, J. Compos. Technol. Res. 15, 269–281.
O’Brien TK (1998), Composite interlaminar shear fracture toughness, GIIc: Shear measurement or sheer Myth?, Composite Materials: Fatigue and Fracture, Seventh Volume, ASTM STP 1330, Am Soc for Testing and Materials, West Conshohocken, PA, 3–18.
Reeder JR and Crews JH (1990), Mixed mode bending method for delamination testing, AIAA J. 28, 1270–1276.
Reeder JR and Crews JH (1992), Redesign of the mixed-mode bending delamination test to reduce nonlinear effects, J. Compos. Technol. Res. 14(1), 12–19.
Reeder JR (1993), A bilinear failure criterion for mixed-mode delamination, Composite Materials: Testing and Design, Eleventh Volume, ASTM STP 1206, Am Soc for Testing and Materials, Philadelphia, PA, 303–322.
Ko¨nig M, Kru¨ger, R, Kussmaul, K, v. Alberti, M, and Ga¨dke, M (1997), Characterizing static and fatigue interlaminar fracture behavior of a first generation graphite/epoxy composite, Composite Materials: Testing and Design, 13th Volume, ASTM STP 1242, SJ Hooper (ed), Am Soc for Testing and Materials, Philadelphia, PA, 60–81.
Hansen P and Martin R (1999), DCB, 4ENF and MMB delamination characterisation of S2/8552 and IM7/8552, N68171-98-M-5177, Materials Engineering Research Laboratory Ltd. (MERL), Hertford, UK.
Lee SM (1990), Failure mechanics of edge delamination of composites, J. Compos. Mater. 24, 1200–1212.
Martin RH (1991), Evaluation of the split cantilever beam for mode III delamination testing, pp. 243–266, Composite Materials: Fatigue and Fracture, Third Volume, ASTM STP 1110, Philadelphia, PA.
Robinson P and Song DQ (1994), Development of an improved mode III delamination test for composites, Compos. Sci. Technol. 52(2), 217–233.
Li J , Lee SM, Lee EW, and O’Brien TK (1997), Evaluation of the edge crack torsion ECT test for Mode III interlaminar fracture toughness of laminated composites, J. Compos. Technol. Res. 19, 174–183.
Rybicki EF and Kanninen MF (1977), A finite element calculation of stress intensity factors by a modified crack closure integral, Eng. Fract. Mech. 9, 931–938.
Rybicki EF , Schmueser DW, and Fox J (1977), An energy release rate approach for stable crack growth in the free-edge delamination problem, J. Compos. Mater. 11, 470–487.
Raju IS (1987), Calculation of strain-energy release rates with higher order and singular finite elements, Eng. Fract. Mech. 28, 251–274.
Buchholz FG, Grebner, H, Dreyer, KH, and Krome, H (1988), 2D- and 3D-applications of the improved and generalized modified crack closure integral method, Computational Mechanics ’88, SN Atluri and G Yagawa (eds), Springer Verlag, New York.
Miravete A and Jime´nez MA (2002), Application of the finite element method to prediction of onset of delamination growth, Appl. Mech. Rev. 55(2), 89–105.
Ingraffea A and Wawrzynek, P (1995), FRANC2D: A case study in transfer of software technology, Research Transformed into Practice: Implementations of NSF Research, J Colville and A Amde (ed), ASCE Press, New York, 233–344.
Singh R , Carter BJ, Wawrzynek PA, and Ingraffea AR (1998), Universal crack closure integral for SIF estimation, Eng. Fract. Mech. 60(2), 133–146.
St. Doltsinis J, Knapp H, Streiner P, and Wu¨stenberg H, (1985), PERMAS-FM, Fracture mechanics, User Manual, Publication No 226, Rev C INTES GmbH, Stuttgart, Germany.
Kru¨ger R, Ko¨nig M, and Schneider T (1993), Computation of local energy release rates along straight and curved delamination fronts of unidirectionally laminated DCB- and ENF—specimens, Proc of the 34th AIAA/ASME/ASCE/AHS/ASC SSDM Conf, La Jolla, Am Inst of Aeronaut and Astronaut, Washington, 1332–1342.
Parks DM (1974), A stiffness derivative finite element technique for determination of crack tip stress intensity factors, Int. J. Fract. 10, 487–502.
Parks DM (1977), The virtual crack extension method for nonlinear material behavior, Comput. Methods Appl. Mech. Eng. 12, 353–364.
Parks DM (1978), Virtual crack extension: A general finite element technique for J-integral evaluation, Numerical Methods in Fracture Mechanics, AR Luxmoore and DRJ Owen (eds), Pineridge Press, Swansea, UK, 464–479.
Delorenzi HG (1982), On the energy release rate and the J-integral for 3-D crack configurations, Int. J. Fract. 19, 183–193.
Delorenzi HG and Shih CD (1983), 3-D Elastic-plastic investigation of fracture parameters in side-grooved compact specimen, Int. J. Fract. 21, 195–220.
Delorenzi HG (1985), Energy release rate calculations by the finite element method, Eng. Fract. Mech. 21, 129–143.
Lin SC and Abel JF (1988), Variational aproach for a new direct-integration form of the virtual crack extension method, Int. J. Fract. 38, 217–235.
Claydon PW (1992), Maximum energy release rate distribution from a generalized 3D virtual crack extension method, Eng. Fract. Mech. 42(6), 961–969.
Hwang CG , Wawrzynek PA, Tayebi AK, and Ingraffea AR (1998), On the virtual crack extension method for calculation of the rates of energy release rate, Eng. Fract. Mech. 59(4), 521–542.
Ishikawa H (1980), A finite element analysis of stress intensity factors for combined tensile and shear loading by only a virtual crack extension, Int. J. Fract. 16, R243–R246R243–R246.
Sha GT (1984), On the virtual crack extension technique for stress intensity factors and energy release rate calculations for mixed fracture mode, Int. J. Fract. 25, R33–R42R33–R42.
Li FZ , Shih CF, and Needleman A (1985), A comparison of methods for calculating energy-release rates, Eng. Fract. Mech. 21(2), 405–421.
Moran B and Shih CF (1987), Crack tip and associated domain integrals from momentum and energy-balance, Eng. Fract. Mech. 27(6), 615–642.
Nikishkov GP and Atluri SN (1987), Calculation of fracture-mechanics parameters for an arbitrary 3-dimensional crack, by the equivalent domain integral method, Int. J. Numer. Methods Eng. 24(9), 1801–1821.
Nikishkov GP and Atluri SN (1987), An equivalent domain integral method for computing crack-tip integral parameters in nonelastic, thermomechanical fracture, Eng. Fract. Mech. 26(6), 851–867.
Raju IS and Shivakumar KN (1990), An equivalent domain integral method in the two-dimensional analysis mixed-mode crack problems, Eng. Fract. Mech. 37(4), 707–725.
Shivakumar KN and Raju IS (1992), An equivalent domain integral method for three-dimensional mixed-mode fracture problems, Eng. Fract. Mech. 42(6), 935–959.
Banks-Sills L (1991), Application of the finite element method to linear elastic fracture mechanics, Appl. Mech. Rev. 44(10), 447–461.
Chow WT and Atluri SN (1997), Stress intensity factors as the fracture parameters for delamination crack growth in composite laminates, Composites, Part B 28B(4), 375–384.
Gosz M and Moran B (2002), An interaction energy integral method for computation of mixed-mode stress intensity factors along non-planar crack fronts in three dimensions, Eng. Fract. Mech. 69(3), 299–319.
Park O and Sankar BV (2002), Crack-tip force method for computing energy release rate in delaminated plates, Compos. Struct. 55(4), 429–434.
Scho¨n J and Andersson B (1998), Calculation of mode-separated energy release rates during delamination growth, Proc of Am Soc for Composites—13th Technical Conf on Composite Materials, Am Soc for Composities Dayton, OH.
Mukhopadhyay NK , Kakodkar A, and Maiti SK (1998), Further considerations in modified crack closure integral based computation of stress intensity factor in BEM, Eng. Fract. Mech. 59(3), 269–279.
Irwin GR (1958), Fracture I, Handbuch der Physik VI, Flu¨gge (ed), Springer Verlag, Berlin, Germany, 558–590.
Broek D (1991), Elementary Engineering Fracture Mechanics, 4th Revised Edition, Kluwer Academic Publishers, Dordrecht, Netherlands.
Buchholz FG (1984), Improved formulae for the FE-calculation of the strain energy release rate by the modified crack closure integral method, Proceedings of the 4th World Congress on Finite Elements, Interlaken, Robinson and Assoc, Dorset, 650–659.
Buchholz FG and Meiners B (1984), On the accuracy of the modified crack closure integral method in combination with higher order finite elements, Accuracy Estimates and Adaptive Refinements in Finite Element Computations, Proc of Int Conf, Lisbon, Technical University of Lisbon, Lisbon, I, 131–140.
Barsoum RS (1976), On the use of isoparametric finite elements in linear fracture mechanics, Int. J. Numer. Methods Eng. 10, 25–37.
Barsoum RS (1977), Triangular quarter-point elements as elastic and perfectly-plastic crack tip elements, Int. J. Numer. Methods Eng. 11, 85–98.
Murti V and Valliappan S (1986), A universal optimum quarter point element, Eng. Fract. Mech. 25(2), 237–258.
Narayana KB , Dattaguru B, Ramamurthy TS, and Vijayakumar K (1990), Modified crack closure integral using six-noded isoparametric quadrilateral singular elements, Eng. Fract. Mech. 36(6), 945–955.
Henshell RD and Shaw KG (1975), Crack tip finite elements are unnecessary, Int. J. Numer. Methods Eng. 9, 496–507.
Ramamurthy TS , Krishnamurthy T, Narayana KB, Vijayakumar K, and Dattaguru B (1986), Modified crack closure integral method with quarter point elements, Mech. Res. Commun. 13(4), 179–186.
Lim IL , Johnston IW, and Choi SK (1991), The use of transition-elements, Eng. Fract. Mech. 40(6), 975–983.
Narayana KB and Dattaguru B (1996), Certain aspects related to computation by modified crack closure integral (MCCI), Eng. Fract. Mech. 55(2), 335–339.
Sethuraman R and Maiti SK (1988), Finite element based computation of strain energy release rate by modified crack closure integral, Eng. Fract. Mech. 30(2), 227–231.
Shivakumar KN , Tan PW, and Newman JC (1988), A virtual crack-closure technique for calculating stress intensity factors for cracked three dimensional bodies, Int. J. Fract. 36, R43–R50R43–R50.
Raju IS , Sistla R, and Krishnamurthy T (1996), Fracture mechanics analyses for skin-stiffener debonding, Eng. Fract. Mech. 54(3), 371–385.
Raju IS , Shivakumar KN, and Crews JH, Jr ( 1988), Three-dimensional elastic analysis of a composite double cantilever beam specimen, AIAA J. 26, 1493–1498.
Roeck GD and Wahab MMA (1995), Strain energy release rate formulae for 3D finite element, Eng. Fract. Mech. 50, 569–580.
Whitcomb JD and Shivakumar KN (1989), Strain-energy release rate analysis of plates with postbuckled delaminations, J. Compos. Mater. 23, 714–734.
Buchholz FG (1994), Finite element analysis of a 3D mixed-mode fracture problem by virtual crack closure integral method, Proceedings of the Indo-German Workshop, AVK Murthy and FG Buchholz (eds), Indian Institute of Science, Interline Publications, Bangalore, 7–12.
Narayana KB , George S, Dattaguru B, Ramamurthy TS, and Vijayakumar K (1994), Modified crack closure integral (MCCI) for 3-d problems using 20-noded brick elements, Fatigue Fract. Eng. Mater. Struct. 17(2), 145–157.
Singh R , Patel SK, and Dattaguru B (1999), Decomposed crack closure integrals for estimation of SIF variations, Eng. Fract. Mech. 63(2), 165–178.
He W-J , Lin Y, and Ding H-J (1997), A three-dimensional formula for determining stress intensity factors in finite element analysis of cracked bodies, Eng. Fract. Mech. 57(4), 409–415.
Wang JT and Raju IS (1996), Strain energy release rate formulae for skin-stiffener debond modeled with plate elements, Eng. Fract. Mech. 54(2), 211–228.
Glaessgen EH, Riddell WT, and Raju IS (1998), Effect of shear deformation and continuity on delamination modeling with plate elements, 39rd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference.
Glaessgen EH , Riddell WT, and Raju IS (2002), Nodal constraint, shear deformation and continuity effects related to the modeling of debonding of laminates, using plate elements, CMES3(1), 103–116.
Ko¨nig M, Kru¨ger R, and Rinderknecht S (2000), Finite element analysis of delamination growth in a multidirectional composite ENF specimen, 345–365, Composite Materials: Theory and Practice, P Grant and CQ Rousseau (eds), ASTM STP 1383. Am Soc for Testing and Materials, West Conshohocken, PA.
Krueger R and O’Brien TK (2001), A shell/3D modeling technique for the analysis of delaminated composite laminates, Composites, Part A 32(1), 25–44.
Whitcomb JD (1990), Mechanics of instability-related delamination growth, Composite Materials: Testing and Design, Ninth Volume, SP Garbo (ed), ASTM STP 1059, Am Soc for Testing and Materials, Philadelphia, PA, 215–230.
Smith SA and Raju IS (1998), Evaluation of stress-intensity factors using general finite-element models, Fatigue and Fracture Mechanics, 29th Volume, ASTM STP 1321, TL Panontin and SD Sheppard (eds), Am Soc for Testing and Materials, West Conshohocken, PA.
Kru¨ger R and Ko¨nig M (1997), Prediction of delamination growth under cyclic loading, Composite Materials: Fatigue and Fracture, Sixth Volume, ASTM STP 1285, EA Armanios (ed), Am Soc for Testing and Materials, West Conshohocken, PA, 162–178.
Ferrie CH and Rousseau CQ (2001), A method of applying VCCT to corner crack nodes, Proc of Am Soc for Composites, 16th Annual Technical Conference on Composite Materials, Blacksburg, VA, Am Soc for Composites, Dayton, OH.
Raju IS , Crews JH, and Aminpour MA (1988), Convergence of strain energy release rate components for edge-delaminated composite laminates, Eng. Fract. Mech. 30(3), 383–396.
Hwu C and Hu J (1992), Stress intensity factors and energy release rates of delaminations in composite laminates, Eng. Fract. Mech. 42(6), 977–988.
Sun CT and Jih CJ (1987), On strain energy release rates for interfacial cracks in bimaterial media, Eng. Fract. Mech. 28(1), 13–20.
Sun CT and Manoharan MG (1989), Strain energy release rates of an interfacial crack between two orthotropic solids, J. Compos. Mater. 23, 460–478.
Dattaguru B , Venkatesha KS, Ramamurthy TS, and Buchholz FG (1994), Finite element estimates of strain energy release rate components at the tip of an interface crack under mode I loading, Eng. Fract. Mech. 49(3), 451–463.
Beuth JL and Narayan SH (1997), Separation of crack extension modes in composite delamination problems, Composite Materials: Fatigue and Fracture, Sixth Volume, ASTM STP 1285, EA Armanios (ed), Am Soc for Testing and Materials, West Conshohocken, PA, 324–342.
Huang H and Kardomateas GA (2001), Mixed-mode stress intensity factors for cracks located at or parallel to the interface in bimaterial half planes, Int. J. Solids Struct. 38(21), 3719–3734.
Qian W and Sun CT (1997), Calculation of stress intensity factors for interlaminar cracks in composite laminates, Compos. Sci. Technol. 57(6), 637–650.
Qian W and Sun CT (1998), Methods for calculating stress intensity factors for interfacial cracks between two orthotropic solids, Int. J. Solids Struct. 35(25), 3317–3330.
Boniface V and Simha KRY (1999), Re-examination of crack opening model of interface fracture, Eng. Fract. Mech. 64(6), 677–691.
Sun CT and Qian W (1997), The use of finite extension strain energy release rates in fracture of interfacial cracks, Int. J. Solids Struct. 34(20), 2595–2609.
Venkatesha KS , Dattaguru B, and Ramamurthy TS (1996), Finite-element analysis of an interface crack with large crack-tip contact zones, Eng. Fract. Mech. 54(6), 847–860.
Venkatesha KS , Dattaguru B, and Ramamurthy TS (1996), Generalized modified crack closure integral (GMCCI) and its application to interface crack problems, Comput. Struct. 60(4), 665–676.
Venkatesha KS , Ramamurthy TS, and Dattaguru B (1998), A study of the behavior of subinterface cracks in bimaterial plates, Eng. Fract. Mech. 59(2), 241–252.
Zou Z , Reid SR, Soden PD, and Li S (2001), Mode separation of energy release rate for delamination in composite laminates using sublaminates, Int. J. Solids Struct. 38(15), 2597–2613.
Morais ABd , Moura MFd, Marques AT, and Castro PTd (2002), Mode-I interlaminar fracture of carbon/epoxy cross-ply composites, Compos. Sci. Technol. 62(5), 679–686.
O’Brien TK (2001), personal communication.
Kru¨ger R (1994), Three dimensional finite element analysis of multidirectional composite DCB, SLB and ENF specimens ISD-Report No 94/2, Institute for Statics and Dynamics of Aerospace Structures, University of Stuttgart.
Davidson BD , Kru¨ger R, and Ko¨nig M(1995), Three dimensional analysis and resulting design recommendations for unidirectional and multidirectional end-notched flexure tests, J. Compos. Mater. 29(16), 2108–2133.
Davidson BD , Kru¨ger R, and Ko¨nig M(1995), Three dimensional analysis of center delaminated unidirectional and multidirectional single leg bending specimens, Compos. Sci. Technol. 54(4), 385–394.
Krueger R and O’Brien TK (2000), A shell/3D modeling technique for the analysis of delaminated composite laminates, NASA/TM-2000-210287, ARL-TR-2207.
Sih GC , Paris PC, and Irwin GR(1965), On cracks in rectilinearly anisotropic bodies, Int. J. Fract. Mech. 1, 189–203.
Krueger R , Paris IL, O’Brien TK, and Minguet PJ(2002), Comparison of 2D finite element modeling assumptions with results from 3D analysis for composite skin-stiffener debonding, Compos. Struct. 57(1–4), 161–168.
Ramakumar RL and Whitcomb JD (1985), Characterization of mode I and mixed-mode delamination growth in T300/5208 graphite/epoxy, Delamination and Debonding of Materials, ASTM STP 876, WS Johnson (ed), Am Soc for Testing and Materials, Philadelphia, PA, 315–335.
Rybicki EF , Hernandez TD, Deibler JE, Knight RC, and Vinson SS (1987), Mode I and mixed mode energy release rate values for delamination of graphite/epoxy test specimens, J. Compos. Mater. 21, 105–123.
Tanzawa Y , Watanabe N, and Ishikawa T(2001), FEM simulation of a modified DCB test for 3-D orthogonal interlocked fabric composites, Compos. Sci. Technol. 61(8), 1097–1107.
Rhee KY (1997), On the validity of applying the elastic work factor approach to determine GIc of fiber-reinforced laminated composites, Compos. Struct. 37(1), 57–63.
Rikards R , Buchholz FG, Wang H, Bledzki AK, Korjakin A, and Richard HA(1998), Investigation of mixed mode I/II interlaminar fracture toughness of laminated composites by using a CTS type specimen, Eng. Fract. Mech. 61(3–4), 325–342.
Rikards R , Korjakin A, Buchholz FG, Wang H, Bledzki AK, and Wacker G(1998), Interlaminar fracture toughness of GFRP influenced by fiber surface treatment, J. Compos. Mater. 32(17), 1528–1559.
Jose S , Kumar RR, Janab MK, and Rao GV(2001), Intralaminar fracture toughness of a cross-ply laminate and its constituent sub-laminates, Compos. Sci. Technol. 61, 1115–1122.
Pieracci A , Davidson BD, and Sundararaman V(1998), Nonlinear analyses of homogeneous, symmetrically delaminated single leg bending specimens, J. Compos. Technol. Res. 20(3), 170–178.
Schuecker C and Davidson BD (2000), Effect of friction on the perceived mode II delamination toughness from three- and four-point bend end-notched flexure tests, Composite Materials: Theory and Practice, ASTM STP 1383, P Grant and CQ Rousseau (eds) Am Soc for Testing and Materials, West Conshohocken, PA, 334–344.
Wang H, Ding, S, Buchholz, FG, and Rikards, R (1994), Delamination analysis for 2D- and 3D-models of a cross-ply laminated three-point bending specimen, Localized Damage III, MH Alı´abadı´, A Carpinterı´, S Kalinsky, and DJ Cartwright (eds), Computational Mechanics Publ, Southampton, UK and Boston, MA, 251–258.
Bansal A and Kumosa M(1998), Analysis of double edge-cracked iosipescu specimens under biaxial loads, Eng. Fract. Mech. 59(1), 89–100.
Buchholz FG, Bu¨rger M, Kumosa M, and Eggers H (1990), Mixed-mode fracture analysis of orthotropic laminates by local and global energy methods, Numerical Methods in Fracture Mechanics, AR Luxmorre and DRJ Owen (eds), Pineridge Press, Swansea, UK, 391–402.
Whitcomb JD and Raju IS (1985), Analysis of interlaminar stresses in thick composite laminates with and without edge delamination, Delamination and Debonding of Materials, ASTM STP 876, WS Johnson (ed), Am Soc for Testing and Materials, Philadelphia, PA, 69–94.
Li J , O’Brien TK, and Rousseau CQ(1997), Test and analysis of composite hat stringer pull-off test specimens, J. Am. Helicopter Soc. 350–357.
Li J (2000), Flange delamination prediction in composite structures with ply waviness, AIAA J. 38(5), 893–897.
Wahab MMA (2000), On the use of fracture mechanics in designing a single lap adhesive joint, J. Adhes. Sci. Technol. 14(6), 851–865.
Qin M and Dzenis Y (2001), Nonlinear numerical and experimental analysis of single lap adhesive composie joints with delaminated adherends, Proc of Thirteenth Int Conf on Composite Materials (ICCM13), Y Zhang (ed), Beijing.
Johnson WS, Butkus, LM, and Valentin, RV (1998), Applications of fracture mechanics to the durability of bonded composite joints, DOT/FAA/AR-97/56, US Department of Transportation, Federal Aviation Administration.
Goswamia S and Becker W(2001), The effect of facesheet/core delamination in sandwich structures under transverse loading, Compos. Struct. 54(4), 515–521.
Ratcliffe JGA (2001), Ph.D. thesis, The University of Liverpool.
Cantwell WJ , Scudamore R, Ratcliffe J, and Davies P(1999), Interfacial fracture in sandwich laminates, Compos. Sci. Technol. 59, 2079–2085.
Glaessgen EH, Sleight DW, Krishnamurthy T, and Raju IS (2001), Analyses for debonding of stitched composite sandwich structures using improved constitutive models, 42nd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference.
Whitcomb JD (1984), Strain-energy release rate analysis of cyclic delamination growth in compressively loaded laminates, Effect of Defects in Composite Materials, ASTM STP 836, Am Soc for Testing and Materials, Philadelphia, PA, 175–193.
Hwang S-F and Mao C-P(2001), Failure of delaminated interply hybrid composite plates under compression, Compos. Sci. Technol. 61(11), 1513–1527.
Singh KL, Dattaguru B, Ramamurthy TS, and Mangalgiri PD (1999), 3D fracture analysis of delaminations in laminated composites, Modeling and Simulation Based Engineering, Vol II, SN Atluri and PE O’Donoghue (eds), Tech Science Press, Encino, CA, 1592–1597.
Murri GB , O’Brien TK, and Rousseau CQ(1998), Fatigue life methodology for tapered composite flexbeam laminates, J. Am. Helicopter Soc. 43, 146–155.
Murri GB, Schaff JR, and Dobyns AL (2001), Fatigue and damage tolerance analysis of a hybrid composite tapered flexbeam, Proceedings of the American Helicopter Society 57th Annual Forum, Washington, DC, May 9–11.
Krueger R , Paris IL, O’Brien TK, and Minguet PJ(2002), Fatigue life methodology for bonded composite skin/stringer configurations, J. Compos. Technol. Res. 24(2), 56–79.
Minguet PJ and O’Brien, TK (1995), Analysis of composite skin/stringer bond failures using a strain energy release rate approach, The Tenth International Conference on Composite Materials, Vol I, A Poursartip and K Street (eds), 245–252.
Minguet PJ (1997), Analysis of the strength of the interface between frame and skin in a bonded composite fuselage panel, The 38rd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, 2783–2790.
Krueger R , Cvitkovich MK, O’Brien TK, and Minguet PJ(2000), Testing and analysis of composite skin/stringer debonding under multi-axial loading, J. Compos. Mater. 34(15), 1263–1300.
Hoyt DM , Ward SH, and Minguet PJ(2002), Strength and fatigue life modeling of bonded joints in composite structure, J. Compos. Technol. Res. 24(3), 190–210.
Flanagan G (1994), A general sublaminate analysis method for determining strain energy release rates in composites, The 35rd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, 381–389.
Yap JWH , Scott ML, Thomson RS, and Hachenberg D(2002), The analysis of skin-to-stiffener debonding in composite aerospace structures, Compos. Struct. 57(1–4), 425–435.
Kumar RR and Rao GV (2001), Some studies on interlaminar and intralaminar fracture toughness of multilayered composite structures, Proceedings of the Thirteenth International Conference on Composite Materials (ICCM13), Y Zhang (ed), Beijing.
Glaessgen EH, Raju IS, and Poe CC (1998), Fracture mechanics analysis of stitched stiffener-skin debonding, The 39th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, Long Beach, California, AIAA 98-2022, April 20–23.
Glaessgen EH, Raju, IS, and Poe CC (1999), Delamination and stitch failure in stitched composite joints, Proceedings of the 40th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference.
Glaessgen EH, Raju IS, and Poe CC (1999), Debonding of stitched composite joints: Testing and analysis, Society for Experimental Mechanics Spring Conference and Exposition, Cincinnati, Ohio, June 7–9.
Rinderknecht S and Kro¨plin B(1995), A finite element model for the delamination in composite plates, Mech. Compos. Mater. Struct. 2, 19–47.
Rinderknecht S and Kroplin B(1997), Computational method for the analysis of delamination growth in composite plates, Comput. Struct. 64(1–4), 359–374.
Klug J , Wu XX, and Sun CT(1996), Efficient modeling of postbuckling delamination growth in composite laminates using plate elements, AIAA J. 34(1), 178–184.
Zheng S and Sun CT(1998), Delamination interaction in laminated structures, Eng. Fract. Mech. 59(2), 225–240.
Reeder J, Song K, Chunchu P, and Ambur D (2002), Postbuckling and growth of delaminations in composite plates subjected to axial compression, The 43rd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference.
Crews JH , Shivakumar KN, and Raju IS(1991), Strain energy release rate distribution for double cantilever beam specimens, AIAA J. 29, 1686–1691.
Davidson BD , Kru¨ger R, and Ko¨nig M(1996), Effect of stacking sequence on energy release rate distributions in multidirectional DCB and ENF specimens, Eng. Fract. Mech. 55(4), 557–569.
Shivakumar K, Ghantae S, and Sharpe M (2001), Split angle-ply beam specimen for measurement of fracture toughness with mode III stress state, Proc of the Thirteenth Int Conf on Composite Materials (ICCM13), Y Zhang (ed), Beijing.
Suemasu H (1999), An experimental method to measure the mode-III interlaminar fracture toughness of composite laminates, Compos. Sci. Technol. 59(7), 1015–1021.
Dhondt G , Chergui A, and Buchholz F-G(2001), Computational fracture analysis of different specimens regarding 3D and mode coupling effects, Eng. Fract. Mech. 68(4), 383–401.
Wang H, Buchholz FG, and Rikards R (1995), Delamination analysis of an angle-ply laminated three-point bending specimen, Computational Mechanics ’95: Theory and Application, SN Atluri, G Yagawa, and TA Cruse (eds), Springer, Heidelberg, Vol. II, 2323–2328.
Salpekar SA and O’Brien TK (1991), Combined effect of matrix cracking and free edge on delamination, Composite Materials: Fatigue and Fracture, Third Volume, ASTM STP 1110, Am Soc for Testing and Materials, Philadelphia, PA, 287–311.
Kaczmarek K , Wisnom MR, and Jones MI(1998), Edge delamination in curved 04/±456s glass-fibre/epoxy beams loaded in bending, Compos. Sci. Technol. 58(1), 155–161.
Lindemann J and Becker W(2002), The tendency for free-edge delamination in laminates and its minimization, Compos. Sci. Technol. 62(2), 233–242.
Burianek DA and Spearing SM (2001), Interacting damage modes in titanium-graphite hybrid laminates, Proc of the Thirteenth Int Conf on Composite Materials (ICCM13), Y Zhang (ed), Beijing.
Ireman T , Thesken JC, Greenhalgh E, Sharp R, Ga¨dke M, Maison S, Ousset Y, Roudolff F, and Barbera AL(1996), Damage propagation in composite structural elements-coupon experiments and analyses, Compos. Struct. 36(3–4), 209–220.
Kru¨ger R, Ko¨nig M, and Kro¨plin B (1997), Delamination growth in CFRP-laminates: development of a predictive tool based on computational fracture mechanics, Proc of the 38th AIAA/ASME/ASCE/AHS/ASC SSDM Conf, Kissimmee, FL, Am Institute of Aeronautics and Astronautics, Reston, VA, 2064–2072.
Pradhan SC and Tay TE(1998), Three-dimensional finite element modeling of delamination growth in notched composite laminates under compression loading, Eng. Fract. Mech. 60(2), 157–171.
Whitcomb JD (1989), Three-dimensional analysis of a postbuckled embedded delamination, J. Compos. Mater. 23, 862–889.
Whitcomb JD (1992), Analysis of a laminate with a postbuckled embedded delamination, including contact effects, J. Compos. Mater. 26, 1523–1535.
Shivakumar KN and Whitcomb JD(1985), Buckling of a sublaminate in a quasi-isotropic laminate, J. Compos. Mater. 19, 2–18.
Gaudenzi P , Perugini P, and Riccio A(2001), Post-buckling behavior of composite panels in the presence of unstable delaminations, Compos. Struct. 51(2), 301–309.
Tay TE , Shen F, Lee KH, Scaglione A, and Sciuva MD(1999), Mesh design in finite element analysis of post-buckled delamination in composite laminates, Compos. Struct. 47(1–4), 603–611.
Shen F , Lee KH, and Tay TE(2001), Modeling delamination growth in laminated composites, Compos. Sci. Technol. 61(9), 1239–1251.
Riccio A , Perugini P, and Scaramuzzino F(2000), Modeling compression behavior of delaminated composite panels, Comput. Struct. 78, 73–81.
Riccio A , Scaramuzzino F, and Perugini P(2001), Embedded delamination growth in composite panels under compressive load, Composites, Part B 32(3), 209–218.
Pradhan B and Chakraborty D(2000), Fracture behavior of FRP composite laminates with an embedded elliptical delamination at the interface, J. Reinf. Plast. Compos. 19(13), 1004–1023.
Suemasu H and Kumagai T(1998), Compressive behavior of multiply delaminated composite laminates, Part 2: Finite element analysis, AIAA J. 36(7), 1286–1290.
Lachaud F , Lorrain B, Michel L, and Barriol R(1998), Experimental and numerical study of delamination caused by local buckling of thermoplastic and thermoset composites, Compos. Sci. Technol. 58(5), 727–733.
Li J and Sen JK (2001), Analysis of frame-to-skin joint pull-off tests and prediction of the delamination failure, Proc of the 42nd AIAA/ASME/ASCE/AHS/ASC SSDM Conf, Seattle, WA.
Li J (2000), Three-dimensional effect in the prediction of flange delamination in composite skin-Stringer pull-off specimens, Proc of Am Society for Composites—15th Annual Technical Conference on Composite Materials, Technomic Publishing, Lancaster, PA, 983–990.
Krueger R and Minguet PJ (2002), Influence of 2D finite element modeling assumptions on debonding prediction for composite skin-stiffener specimens subjected to tension and bending, NASA/CR-2002-211452, ICASE Report No 2002-4.
Kru¨ger R, Rinderknecht S, Ha¨nsel C, and Ko¨nig M (1996), Computational structural analysis and testing: An approach to understand delamination growth, Fracture of Composites, EA Armanios (ed), Trans Tech Publications, Switzerland, 120–121, 181–202.
Parisch H (1995), A continuum-based shell theory for non-linear applications, Int. J. Numer. Methods Eng. 38, 1855–1883.
Parisch H (1989), A consistent tangent stiffness matrix for three-dimensional non-linear contact analysis, Int. J. Numer. Methods Eng. 28, 1803–1812.
Kru¨ger R, Ha¨nsel C, and Ko¨nig M (1996), Experimental-numerical investigation of delamination buckling and growth, ISD-Report No 96/3, Institute for Statics and Dynamics of Aerospace Structures, University of Stuttgart.