The method of assessment of the grinding wheel cutting ability in the plunge grinding
Tóm tắt
This article presents the method of comparative assessment of the grinding wheel cutting ability in the plunge grinding kinematics. A new method has been developed to facilitate multicriterial assessment of the working conditions of the abrasive grains and the bond bridges, as well as the wear mechanisms of the GWAS, which occur during the grinding process, with simultaneous limitation of the workshop tests range. The work hereby describes the methodology of assessment of the grinding wheel cutting ability in a short grinding test that lasts for 3 seconds, for example, with a specially shaped grinding wheel, in plunge grinding. The grinding wheel macrogeometry modification applied in the developed method consists in forming a cone or a few zones of various diameters on its surface in the dressing cut. It presents an exemplary application of two variants of the method in the internal cylindrical plunge grinding, in 100Cr6 steel. Grinding wheels with microcrystalline corundum grains and ceramic bond underwent assessment. Analysis of the registered machining results showed greater efficacy of the method of cutting using a grinding wheel with zones of various diameters. The method allows for comparative tests upon different grinding wheels, with various grinding parameters and different machined materials.
Tài liệu tham khảo
Webster J., Tricard M., Innovations in abrasive products for precision grinding, CIRP ANN, 2004, 2, 597–617
Malkin S., Guo C., Grinding Technology: The Way Things Can Work: Theory and Applications of Machining with Abrasives, Industrial Press, New York, 2008
Klocke F., Manufacturing Processes 2: Grinding, Honing, Lapping, Springler-Verlag, Berlin, 2009
Rowe W.B., Principles of Modern Grinding Technology William Andrew, Burlington, 2009
Jackson M.J., Davim J.P., Machining with Abrasives, Springer, New York, 2010
Słowinski B., Nadolny K., Effective manufacturing method for automated inside diameter grinding, J. Adv. Mech. Des. Sys. & Manuf., 2007, 4, 472–480
Nadolny K., Plichta J., Herman D., Słowinski B., Single-Pass Grinding — An Effective Manufacturing Method for Finishing, In: Proceedings of 19th International Conference on Systems Engineering — ICSENG 2008, (August 19–21, Las Vegas USA), University of Nevada, 2008, 236–241
Marinescu I. D., Rowe W. B., Dimitrov B., Inasaki I., Tribology of abrasive machining processes, William Andrew, Norwich, 2004
Xu X., Yu Y., Huang H., Mechanisms of abrasive wear in the grinding of Titanium (TC4) and Nickel (K417) alloys, WEAR, 2003, 255, 1421–1426
Jackson M.J., Microscale wear of vitrified abrasive materials, J. Mater. Sci., 2004, 39, 2131–2143
Mayer J., Engelhorn R., Bot R., Weirich T., Herwartz C., Klocke F., Wear characteristics of second-phase-reinforced sol-gel corundum abrasives, Acta Mater., 2006, 54, 3605–3615
Wamecke G., Rosenberger U., Milberg J., Basics of Process Parameter Selection in Grinding of Advanced Ceramics, CIRP ANN, 1995, 44, 283–286
Qu W., Wang K., Miller M.H., Huang Y., Chandra A., Using vibration-assisted grinding to reduce subsurface damage. PREC ENG, 2000, 24, 329–337
Brinksmeler E., Glwerzew A., Chip Formation Mechanisms in Grinding at Low Speeds, CIRP ANN, 2003, 52, 253–258
Hamdi H., Dursapt M., Zahouani H., Characterization of abrasive grain’s behavior and wear mechanisms. WEAR, 2003, 254, 1294–1298
Ichida Y., Mechanical properties and grinding performance of ultrafine-crystalline cBN abrasive grains, Diamond Relat. Mater., 2008, 17, 1791–1795
Xu L-M, Xu K-Z, Chai Y-D, Identification of grinding wheel wear signature by a wavelet packet decomposition method, J. Shanghai Jiaotong Univ. (SCI), 2010, 15, 323–328
Ding W.F., Xu J.H., Chen Z.Z., Su H.H, Fu Y.C., Grain wear of brazed polycrystalline CBN abrasive tools during constant-force grinding Ti-6Al-4V alloy, Int. J. Adv. Manuf. Tech., 2011, 52, 969–976
Gołąbczak A., Koziarski T., Assessment method of cutting ability of CBN grinding wheels, Int J Of Mach Tools Manuf, 2005, 45, 1256–1260
Nadolny K., Plichta J., Procedure of examination of the grinding wheel’s cutting ability, Polish Patent Application No. 395409, 2011
Herman D., Plichta J., Karpinski T., Effect of glass-crystalline and amorphous binder application to abrasive tools made of microcrystalline alumina grains type SG, WEAR, 1997, 209, 213–218
Herman D., Glass and glass-ceramic binder obtained from waste material for binding alundum abrasive grains into grinding wheels, CERAM INT, 1998, 24, 515–520
Herman D., Markul J., Influence of microstructures of binder and abrasive grain on selected operational properties of ceramic grinding wheels made of alumina. Int. J. Mach. Tools Manuf., 2004, 44, 511–522
Nadolny K., Device for shaping of conic chamfer on grinding wheels surface for small angular values, Polish Patent Application No. 388765, 2009
Nadolny K., Kapłonek W., Design of a Device for Precision Shaping of Grinding Wheel Macro- and Microgeometry, J. Cent. South Univ. T, 2012, 19, 135–143