Stall, Surge, and 75 Years of Research
Tóm tắt
Work on rotating stall and its related disturbances have been in progress since the Second World War. During this period, certain “hot topics” have come to the fore—mostly in response to pressing problems associated with new engine designs. This paper will take a semihistorical look at some of these fields of study (stall, surge, active control, rotating instabilities, etc.) and will examine the ideas which underpin each topic. Good progress can be reported, but the paper will not be an unrestricted celebration of our successes because, after 75 years of research, we are still unable to predict the stalling behavior of a new compressor or to contribute much to the design of a more stall-resistant machine. Looking forward from where we are today, it is clear that future developments will come from CFD in the form of better performance predictions, better flow modeling, and improved interpretation of experimental results. It is also clear that future experimental work will be most effective when focussed on real compressors with real problems—such as stage matching, large tip clearances, eccentricity, and service life degradation. Today’s topics of interest are mostly associated with compressible effects and so further research will require more high-speed testing.
Từ khóa
Tài liệu tham khảo
1926, Hydraualische Probleme
1936, Pulsierende Förderung bei Pumpenrädern über dem Umfang, Arch. Appl. Mech., 7, 367, 10.1007/BF02090426
1932, Surging in Centrifugal Superchargers
1951, Compressor Surge Investigated by NACA, SAE J., 59, 42
1951, Compressor Surge Topic at SAE Round Table, SAE J., 59, 46
1954, Experimental Investigations of Propagating Stall in Axial-Flow Compressors, ASME
1953, Some Stall and Surge Phenomena in Axial-Flow Compressors, J. Aeronaut. Sci., 20, 835, 10.2514/8.2871
1953, On Asymmetric Flow in an Axial-Flow Compressor Stage, ASME
1955, Compressor Surge and Stall Propagation, ASME
1958, Stall Propagation in a Cascade of Aerofoils, ASME
1957, Rotating Stall Propagation in an Axial Flow Compressor, J. Aeronaut. Sci., 24, 805, 10.2514/8.3975
1972, Non-Linear Analysis of Rotating Stall, ASME J. Eng. Gas Turbines Power, 94, 279, 10.1115/1.3445683
1965, Non-Axisymmetric Flows in Axial Compressors
1954, Observations on the Surging of Various Low-Speed Fans and Compressors
1973
1978, Prediction of Compressor Performance in Rotating Stall, ASME J. Eng. Gas Turbines Power, 100, 1, 10.1115/1.3446318
1959, A Survey of Stall Propagation—Experiment and Theory, ASME J. Basic Eng., 81, 409, 10.1115/1.4008492
1975, On the Partial Flow Rate Performance of Axial-Flow Compressor and Rotating Stall. First Report: Influence of Hub-Tip Ratio and Stators, Bull. JSME, 18, 256, 10.1299/jsme1958.18.256
1978, The Measurement and Interpretation of Flow Within Rotating Stall Cells in Axial Compressors, J. Mech. Eng. Sci., 20, 101, 10.1243/JMES_JOUR_1978_020_017_02
Day, I. J., 1976, “Axial Compressor Stall,” Ph.D. thesis, University of Cambridge, Cambridge, UK.
1949, Surging of Axial Compressors, R. Aeronaut. Soc., Aeronaut. Q., 1, 195
1970, Axial Compressor Stall
1976, Surge and Rotating Stall in Axial Flow Compressors—Part I: Theoretical Compression System Model, ASME J. Eng. Gas Turbines Power, 98, 190, 10.1115/1.3446138
1976, Surge and Rotating Stall in Axial Flow Compressors—Part II: Experimental Results and Comparison With Theory, ASME J. Eng. Gas Turbines Power, 98, 199, 10.1115/1.3446139
1982, A Simple Model for Compressor Stall Cell Propagation, ASME J. Eng. Gas Turbines Power, 104, 170, 10.1115/1.3227246
1984, A Theory of Rotating Stall of Multistage Axial Compressors: Part I—Small Disturbances, ASME J. Eng. Gas Turbines Power, 106, 313, 10.1115/1.3239565
1984, A Theory of Rotating Stall of Multistage Axial Compressors: Part II—Finite Disturbances, ASME J. Eng. Gas Turbines Power, 106, 321, 10.1115/1.3239566
1984, A Theory of Rotating Stall of Multistage Axial Compressors: Part III—Limit Cycles, ASME J. Eng. Gas Turbines Power, 106, 327, 10.1115/1.3239567
1986, Axisymmetrically Stalled Flow Performance for Multistage Axial Compressors, ASME J. Turbomach., 108, 216, 10.1115/1.3262040
1986, A Theory of Post-Stall Transients in Axial Compression Systems: Part I—Development of Equations, ASME J. Eng. Gas Turbines Power, 108, 68, 10.1115/1.3239887
1986, A Theory of Post-Stall Transients in Axial Compression Systems: Part II—Application, ASME J. Eng. Gas Turbines Power, 108, 231, 10.1115/1.3239893
1987, Method for Assessing Effects of Circumferential Flow Field Distortion on Compressor Stability, ASME J. Turbomach., 109, 371, 10.1115/1.3262116
1990, Stability of Flow Through Multistage Axial Compressors, ASME J. Turbomach., 112, 126, 10.1115/1.2927409
1989, Active Suppression of Aerodynamic Instabilities in Turbomachines, J. Propul. Power, 5, 204, 10.2514/3.23137
1988
1991, Active Stabilization of Centrifugal Compressor Surge, ASME J. Turbomach., 113, 723, 10.1115/1.2929139
1991, Dynamic Control of Centrifugal Compressor Surge Using Tailored Structures, ASME J. Turbomach., 113, 710, 10.1115/1.2929138
1993, Active Control of Rotating Stall in a Low Speed Axial Compressor, ASME J. Turbomach., 115, 48, 10.1115/1.2929217
1993, Active Suppression of Rotating Stall and Surge in Axial Flow Compressors, ASME J. Turbomach., 115, 40, 10.1115/1.2929216
1987, Stall Cell Development in an Axial Compressor, ASME J. Turbomach., 109, 492, 10.1115/1.3262138
1998, A Study of Spike and Modal Stall Phenomena in a Low Speed Axial Compressor, ASME J. Turbomach., 120, 393
1994, Active Stabilization of Rotating Stall in a Three-Stage Axial Compressor, ASME J. Turbomach., 116, 226, 10.1115/1.2928357
1995, Dynamic Control of Rotating Stall in Axial Flow Compressors Using Aeromechanical Feedback, ASME J. Turbomach., 117, 307, 10.1115/1.2835665
1998, Active Stabilization of Rotating Stall and Surge in a Transonic Single-Stage Axial Compressor, ASME J. Turbomach., 120, 625, 10.1115/1.2841772
1998, Experiments in Active Control of Stall on an Aeroengine Gas Turbine, ASME J. Turbomach., 120, 637, 10.1115/1.2841773
1998
1994, The Unstable of Low and High Speed Compressors, ASME J. Turbomach., 116, 194, 10.1115/1.2928353
1999, Stall Inception and the Prospects for Active Control in Four High Speed Compressors, ASME J. Turbomach., 121, 18, 10.1115/1.2841229
1995, Pre-Stall Behaviour of Several High-Speed Compressors, ASME J. Turbomach., 117, 62, 10.1115/1.2835644
Bonnaure, L., 1991, “Modelling High Speed Multistage Compressor Stability,” M.S. thesis, Department of Aeronautics and Astronautics, Massachusetts Institute of Technology, Cambridge, MA.
Hendricks, G., Bonnaure, L., Longley, J., Greitzer, E., and Epstein, A., 1993, “Analysis of Rotating Stall Onset in High Speed Axial Flow Compressors,” 29th Joint Propulsion Conference and Exhibit, Monterey, CA.10.2514/6.1993-2233
2000, Influence of Compressor Deterioration on Engine Dynamic Behaviour and Transient Stall-Margin, ASME J. Turbomach., 122, 477, 10.1115/1.1303817
1980, Surge-Induced Structural Loads in Gas Turbines, ASME J. Eng. Gas Turbines Power, 102, 162, 10.1115/1.3230217
1979, A Rotating Stall Control System for Turbojet Engines, ASME J. Eng. Gas Turbines Power, 101, 305, 10.1115/1.3446574
1991, Rotating Waves as a Stall Inception Indicator in Axial Compressors, ASME J. Turbomach., 113, 290, 10.1115/1.2929105
Bright, M., Qammar, H., Vhora, H., and Schaffer, M., 1998, “Rotating Pip Detection and Stall Warning in High-Speed Compressors Using Structure Functions,” AGARD RTO AVT Conference, Toulouse, France, pp. 1–7.
1986, Experimental Investigation of Airfoil and Endwall Boundary Layers in a Subsonic Compressor Stage, ASME, 10.1115/86-GT-143
1991, Detection of a Rotating Stall Precursor in Isolated Axial Flow Compressor Rotors, ASME J. Turbomach., 113, 281, 10.1115/1.2929102
1995, Monitoring of Aerodynamic Load and Detection of Stall in Multistage Compressors, ASME J. Turbomach., 117, 81, 10.1115/1.2835645
2008, Development and Demonstration of a Stability Management System for Gas Turbine Engines, ASME J. Turbomach., 130, 031011, 10.1115/1.2777176
2012, Stall Warning by Blade Passing Signature Analysis, ASME J. Turbomach., 135, 011033, 10.1115/1.4006426
1985, Development of Small Rotating Stall in a Single Stage Axial Compressor, ASME, 10.1115/85-GT-227
1997, Experimental Study of Tip Clearance Losses and Noise in Axial Turbomachines and Their Reduction, ASME J. Turbomach., 119, 460, 10.1115/1.2841145
2001, Comparative Studies on Short and Long Length-Scale Stall Cell Propagating in an Axial Compressor Rotor, ASME J. Turbomach., 123, 24, 10.1115/1.1326085
2001, Rotating Instabilities in an Axial Compressor Originating From the Fluctuating Blade Tip Vortex, ASME J. Turbomach., 123, 453, 10.1115/1.1370160
2002, An Experimental and Numerical Investigation Into the Mechanisms of Rotating Instability, ASME J. Turbomach., 124, 367, 10.1115/1.1460915
1951, Improvements in or Relating to Gas Turbines
1984, A Study on Configurations of Casing Treatment for Axial Flow Compressors, Bull. JSME, 27, 1675, 10.1299/jsme1958.27.1675
2007, Passive Endwall Treatments for Enhancing Stability
1977, Stall Margin Improvement by Casing Treatment—Its Mechanism and Effectiveness, ASME J. Eng. Gas Turbines Power, 99, 121, 10.1115/1.3446241
1984, Flow Phenomena in Compressor Casing Treatment, ASME J. Eng. Gas Turbines Power, 106, 532, 10.1115/1.3239604
1993, Numerical Simulation of Compressor Endwall and Casing Treatment for Flow Phenomena, ASME J. Turbomach., 115, 501, 10.1115/1.2929280
1985, Axial Flow Compressor Surge Margin Improvement
Seitz, P., 1999, “Casing Treatment for Axial Flow Compressors,” Ph.D. thesis, University of Cambridge, Cambridge, MA.
1979, A Fundamental Criterion for the Application of Rotor Casing Treatment, ASME J. Fluids Eng., 101, 237, 10.1115/1.3448945
2010, Stability Enhancement by Casing Grooves: The Importance of Stall Inception Mechanism and Solidity, ASME J. Turbomach., 134, 021003, 10.1115/1.4002986
2014, Tip Gap Variation on a Transonic Rotor in the Presence of Tip Blowing, ASME, 10.1115/GT2014-25042
2011, Self Regulating Casing Treatment for Axial Compressor Stability Enhancement, ASME, 10.1115/GT2011-46042
1997, Computational Study of Rotating-Stall Inception in Axial Compressors, J. Propul. Power, 13, 31, 10.2514/2.5147
1997, Analysis of Instability Inception in High-Speed Multistage Axial-Flow Compressors, ASME J. Turbomach., 119, 714, 10.1115/1.2841181
1999, Prediction and Measurement of Rotating Stall Cells in an Axial Compressor, ASME J. Turbomach., 121, 365, 10.1115/1.2841323
2012, Validation of Numerical Simulation for Rotating Stall in a Transonic Fan, ASME J. Turbomach., 135, 021004, 10.1115/1.4006641
2015, Rotating Stall Observations in a High Speed Compressor—Part I: Experimental Study, ASME J. Turbomach., 137, 051002, 10.1115/1.4028557
2015, Rotating Stall Observations in a High Speed Compressor—Part II: Numerical Study, ASME J. Turbomach., 137, 051003, 10.1115/1.4028558
1989, Part-Circumference Casing Treatment and the Effect on Compressor Stall, ASME, 10.1115/89-GT-312
1999, Role of Blade Passage Flow Structures in Axial Compressor Rotating Stall Inception, ASME J. Turbomach., 121, 735, 10.1115/1.2836727
2008, Criteria for Spike Initiated Rotating Stall, ASME J. Turbomach., 130, 011023, 10.1115/1.2750674
Vo, H. D., 2001, “Role of Tip Clearance Flow on Axial Compressor Stability,” Ph.D. thesis, Massachusetts Institute of Technology, Cambridge, MA.
2013, An Explanation for Flow Features of Spike-Type Stall Inception in an Axial Flow Compressor Rotor, ASME J. Turbomach., 135, 021023, 10.1115/1.4007570