Multiple performance characteristics optimization for Al 7075 on electric discharge drilling by Taguchi grey relational theory
Tóm tắt
Electric discharge drill machine (EDDM) is a spark erosion process to produce micro-holes in conductive materials. This process is widely used in aerospace, medical, dental and automobile industries. As for the performance evaluation of the electric discharge drilling machine, it is very necessary to study the process parameters of machine tool. In this research paper, a brass rod 2 mm diameter was selected as a tool electrode. The experiments generate output responses such as tool wear rate (TWR). The best parameters such as pulse on-time, pulse off-time and water pressure were studied for best machining characteristics. This investigation presents the use of Taguchi approach for better TWR in drilling of Al-7075. A plan of experiments, based on L27 Taguchi design method, was selected for drilling of material. Analysis of variance (ANOVA) shows the percentage contribution of the control factor in the machining of Al-7075 in EDDM. The optimal combination levels and the significant drilling parameters on TWR were obtained. The optimization results showed that the combination of maximum pulse on-time and minimum pulse off-time gives maximum MRR.
Tài liệu tham khảo
Azad MS, Puri AB (2012) Simultaneous optimization of multiple performance characteristics in micro-EDM drilling of titanium alloy. Int J Adv Manuf Technol 61:1231–1239
Bhattacharya R, Jain VK, Ghoshdastidar PS (1996) Numerical simulation of thermal erosion in EDM process. J Inst Eng (I) Prod Eng Div 77:13–19
Bissacco G, Hansen HN, Tristo G, Valentincic J (2011) Feasibility of wear compensation in micro EDM milling based on discharge counting and discharge population characterization. CIRP Ann Manuf Technol 60:231–234
Bursali N, Ertunc S, Akay B (2006) Process improvement approach to the saponification reaction by using statistical experimental design. Chem Eng Process 45:980–989
Caydaş U, Hasçalık A (2008) Use of the grey relational analysis to determine optimum laser cutting parameters with multi-performance characteristics. Optics Laser Technol 40:987–994
Deng J (1982) Control problems of grey systems. Syst Control Lett 5:288–294
Deng J (1989) Introduction to grey system. J Grey Syst 1:1–24
Garg MP, Jain A, Bhushan G (2012) Modelling and multi-objective optimization of process parameters of wire electrical discharge machining using non-dominated sorting genetic algorithm-II. Proc Inst Mech Eng Part B: J Eng Manuf 226:1986–2001
Garna R, Schubert A, Zeidler H (2011) Analysis of the effect of vibrations on the micro-EDM process at the work piece surface. Precis Eng 35:364–368
Ghasemi FA, Raissi S, Malekzadehfard K (2013) Analytical and mathematical modeling and optimization of fiber metal laminates (FMLs) subjected to low-velocity impact via combined response surface regression and zero-one programming. Latin Am J Solids Struct 10:391–408
Gupta P, Khanna R, Gupta RD, Sharma N (2012) Effect of process parameters on kerf width in WEDM for HSLA using response surface methodology. J Eng Technol 2:1–6
Jain VK (2004) Advanced machining processes. Allied, India
Kao JY, Tsao CC, Wang SS, Hsu CY (2010) Optimization of the EDM parameters on machining Ti–6Al–4 V with multiple quality characteristics. Int J Adv Manuf Technol 47(1–4):395–402
Khanna R, Singh H (2013) Performance analysis for D-3 material using response surface methodology on WEDM. Int J Mach Mach Mater 14:45–65
Kumar A, Kumar V, Kumar J (2013) Multi-response optimization of process parameters based on response surface methodology for pure titanium using WEDM process. Int J Adv Manuf Technol 68:2645–2648
Kumar V, Kumar V, Jangra KK (2015) An experimental analysis and optimization of machining rate and surface characteristics in WEDM of Monel-400 using RSM and desirability approach. J Ind Eng Int. doi:10.1007/s40092-015-0103-0
Maity KP, Singh RK (2012) An optimization of micro-EDM operation for fabrication of micro-hole. Int J Adv Manuf Technol 61:1221–1229
McGeough JA (1998) Advanced methods of machining. Chapman and Hall, London
Montgomery DC (2001) Design and analysis of experiments. Wiley, New York
Patel KM, Pandey PM, Rao PV (2010) Optimisation of process parameters for multi-performance characteristics in EDM of Al2O3 ceramic composite. Int J Adv Manuf Technol 47:1137–1147
Sánchez HT, Estrems M, Faura F (2011) Development of an inversion model for establishing EDM input parameters to satisfy material removal rate, electrode wear ratio and surface roughness. Int J Adv Manuf Technol 57(1–4):189–201
Sharma N, Khanna R, Gupta RD, Sharma R (2013a) Modeling and multiresponse optimization on WEDM for HSLA by RSM. Int J Adv Manuf Technol 67:2269–2281
Sharma N, Khanna R, Gupta RD (2013b) Multi Quality Characteristics of WEDM Process Parameters with RSM. Procedia Eng 64:710–719
Sharma N, Khanna R, Gupta RD (2014) WEDM process variables investigation for HSLA by response surface methodology and genetic algorithm. Eng Sci Technol Int J. doi:10.1016/j.jestch.2014.11.004
Sharma N, Raj T, Jangra KK (2015) Parameter optimization and experimental study on wire electrical discharge machining of porous Ni40Ti60 alloy. J Eng Manuf, Proc IMechE Part B. doi:10.1177/0954405415577710
Shokuhfar A, Khalili SMR, Ghasemi FA, Malekzadeh K, Raissi S (2008) Analysis and optimization of smart hybrid composite plates subjected to low-velocity impact using the response surface methodology (RSM). Thin-Walled Struct 46:1204–1212
Simon M, Grama L (2011) Studies for obtaining a small holle, rapid edm drilling machine. Sci Bull Petru Maior Univ Targu Mures 8:189–191
Song KY, Chung DK, Park MS, Chu CN (2009) Micro electrical discharge drilling of tungsten carbide using deionized water. J Micromech Microeng 19:1–10
Wang CC, Yan BH (2000) Blind-hole drilling of Al2O3/6061Al composite using rotary electro-discharge machining. J Mater Process Technol 102:90–102
Yilmaz O, Okka MA (2010) Effect of single and multi-channel electrodes application on EDM fast hole drilling performance. Int J Adv Manuf Technol 51:185–194
Yilmaz O, Bozdana AT, Okka MA, Filiz H (2010) An intelligent and automated system for EDM drilling of super alloys. ICRM: The University of Nottingham, Ningbo, pp 95–99
Yu ZY, Zhang Y, Li J, Luan J, Zhao F, Guo D (2009) High aspect ratio micro-hole drilling aided with ultrasonic vibration and planetary movement of electrode by micro-EDM. CIRP Ann Manuf Technol 58:213–216