Modeling of the Tribological Behavior of Materials Using Crystal Plasticity Constitutive Model. Effect of Heat Partition and Friction
Tóm tắt
A polycrystal model has been developed to study the tribological behavior of an aggregate BCC crystal under extreme contact loading conditions. The polycrystal behavior is defined from the local behavior of a single crystal within the framework of the Hill’s self-consistent scheme by considering the temperature effect. The tribological problem simulated in this work is a contact problem where a pin (tool) moves on a workpiece with a fairly high pressure and large sliding velocity. The results show the importance of the physical parameters as the hardening effect, the restoration of the dislocation and the crystallographic orientations of grains on the contact. The effect of the frictional heat partition and the friction coefficient have been particularly discussed.
Tài liệu tham khảo
Moerlooze, K.D., Farid Al-Bender, F., Van Brussel, H.: A generalised asperity-based friction model. Tribol. Lett. 40, 113–130 (2010)
Smith, E.H., Arnell, R.D.: A new approach to the calculation of flash temperatures in dry, sliding contacts. Tribol. Lett. 53(3), 407–414 (2013)
Smith, E.H., Arnell, R.D.: The prediction of frictional temperature increases in dry, sliding contacts between different materials. Tribol. Lett. 55, 315–328 (2014)
Federici, M., Straffelini, G., Gialanella, G.: Pin-on-disc testing of low-metallic friction material sliding against HVOF coated cast iron: modelling of the contact temperature evolution. Tribol. Lett. 65, 121 (2017)
Westlund, V., Heinrichs, J., Jacobson, S.: On the role of material transfer in friction between metals: initial phenomena and effects of roughness and boundary lubrication in sliding between aluminium and tool steels. Tribol. Lett. 66, 97 (2018)
Abdel-Aal, H.A.: Temperature rise in sliding solids: influence of contact pressure and temperature on thermal conduction. Tribol. Lett. 68, 31 (2020)
Yamaguchi, K., Takakura, N., Imatani, S.: Increase in forming limit of sheet metals by removal of surface roughening with plastic strain (Balanced biaxial stretching of aluminium sheets and foils). J. Mater. Process. Technol. 48, 1–4 (1995)
Wilson, W.R.D.: Modelling tribology in computer simulations of forming processes. In: Proceedings of the 2nd international conference on tribology in manufacturing processes, 1: 13 (2004)
Becker, R.: Effects of strain localization on surface roughening during sheet forming. Acta Mater. 46, 4 (1998)
Raabe, D., Sachtleber, M., Weiland, H., Scheele, G., Zhao, Z.: Grain-scale micromechanics of polycrystal surfaces during plastic straining. Acta Mater 51, 6 (2003)
Jain, M., Lloyd, D.J., MacEwen, S.R.: Hardening laws, surface roughness and biaxial tensile limit strains of sheet aluminium alloys. Int. J. Mech. Sci. 38, 2 (1996)
Zhao, Z., Radovitzky, R., Cuitiño, A.: A study of surface roughening in fcc metals using direct numerical simulation. Acta Mater. 52, 20 (2004)
Zhao, Z., Ramesh, M., Raabe, D., Cuitiño, A.M., Radovitzky, R.: “Investigation of three-dimensional aspects of grain-scale plastic surface deformation of an aluminum oligocrystal. Int. J. Plast. 24, 12 (2008)
Wittridge, N., Knutsen, R.: A microtexture based analysis of the surface roughening behaviour of an aluminium alloy during tensile deformation. Mater. Sci. Eng. A 269, 1 (1999)
Osakada, K., Oyane, M.: On the roughening of free surface in deformation processes. Bull. JSME 14, 171 (1971)
Guangnan, C., Huan, S., Shiguang, H., Baudelet, B.: Roughening of the free surfaces of metallic sheets during stretch forming. Mater. Sci. Eng. A 128, 1 (1990)
Stoudt, M.R., Ricker, R.E.: The relationship between grain size and the surface roughening behavior of Al-Mg alloys. Metall. Mater. Trans. A 33, 2883 (2002)
Bowden, F.P., Tabor, D.: Junction growth in metallic friction: the role of combined stresses and surface contamination. Proc. R. Soc. Lond. Ser. A 251, 1266 (1959)
Emmens, W.C., Schoepen, F.: Some frictional aspects of aluminum in sheet metal forming. In: Proc. 19th IDDRG, Eger, 10:14 (1996)
Li, H.J., Jiang, Z.Y., Wei, D.B.: Crystal plasticity finite modelling of 3D surface asperity flattening in uniaxial planar compression. Tribol. Lett. 46, 101 (2012)
Li, H.J., Jiang, Z.Y., Wei, D.B.: Study on effect of strain rate on 3D surface asperity flattening in uniaxial planar compression by crystal plasticity finite element modelling. Wear 301, 1 (2013)
Li, H.J., Jiang, Z.Y., Wei, D.B.: Influence of friction on surface asperity flattening process in cold uniaxial planar compression (CUPC). Tribol. Int. 66, 282 (2013)
Wang, D.W., Mo, J.L., Ouyang, H., Zhou, Z.R.: Improving dynamic and tribological behaviours by means of a Mn–Cu damping alloy with grooved surface features. Tribol. Lett. 66, 67 (2018)
Li, H., Öchsner, A., Wei, D., Ni, G., Jiang, Z.: Crystal plasticity finite element modelling of the effect of friction on surface asperity flattening in cold uniaxial planar compression. Appl. Surf. Sci. 359, 236 (2015)
Si, L., Lu, Y., Huynh, C., Tieu, N.N., Liu, X.H., Simulation of rolling behaviour of cubic oriented al single crystal with crystal plasticity FEM. J. Mater. Process. Technol. 201, 1–3 (2008)
Jiang, Z.Y., Xiong, S.W., Tieu, A.K., Jane Wang, Q.: Modelling of the effect of friction on cold strip rolling. J. Mater. Process. Technol. 201, 1 (2008)
Franz, G., Abed-Meraim, F., Lorrain, J.-P., Ben Zineb, T., Lemoine, X., Berveiller, M.: Ellipticity loss analysis for tangent moduli deduced from a large strain elastic–plastic self-consistent model. Int. J. Plast. 25, 2 (2009)
Lorrain, J.P.: Ductility criterion based on ellipticity loss of the elastic-plastic tangent modulus deduced from a self-consistent model, PhD Thesis, Université de Lorraine, (2005)
Lorrain, J.P., Ben Zineb, T., Abed-Meraim, F., Berveiller, M.: Ductility loss modelling for BCC single crystals. Int. J. Form. Process 8, 2–3 (2005)
Hill, R., Rice, J.R.: Constitutive analysis of elastic-plastic crystals at arbitrary strain. J. Mech. Phys. Solids 20(6), 401–413 (1972)
Franciosi, P., Zaoui, A.: Crystal hardening and the issue of uniqueness. Int. J. Plast. 7, 4 (1991)
Franciosi, P.: Etude théorique et expérimentale du comportement élastoplastique de monocristaux métalliques se déformant par glissement: Modélisation pour un chargement complexe quasi-statique,” Ph.D. Thesis, Paris North University, France (1984)
Hoc, T.: Etudes expérimentales et numériques de la localisation de la déformation dans les aciers doux, Ph.D. Thesis, Ecole Centrale de Paris, France (1999)
Essmann, U., Mughrabi, H.: Annihilation of dislocations during tensile tests and cyclic deformation and limit of dislocations densities. Phil. Mag. A 40, 6 (1979)
Hill, R.: Generalized constitutive relations for incremental deformation of metal crystals by multislip”. J. Mech. Phys. Solids 14, 2 (1966)
Avevor, Y., Vincent, J., Faure, L., Moufki, A., Philippon, S.: An ALE approach for the chip formation process in high speed machining with transient cutting conditions: Modeling and experimental validation. Int. J. Mech. Sci. 130, 546–557 (2017)
Atlati, S., Haddag, B., Nouari, M., Zenasni, M.: Thermomechanical modelling of the tool–workmaterial interface in machining and its implementation using the ABAQUS VUINTER subroutine. Int. J. Mech. Sci. 87, 102–117 (2014)
Mckinley, J. Simba, H., Worswick, M.: Constitutive modelling of aluminum clad sheet for warm forming. Int. Deep Frawing Res. Gr. (2009)
Rossiter, J., Brahme, A., Simha, M.H., Inal, K., Mishra, R.: A new crystal plasticity scheme for explicit time integration codes to simulate deformation in 3D microstructures: effects of strain path, strain rate and thermal softening on localized deformation in the aluminum alloy 5754 during simple shear. Int. J. Plast. 26, 12 (2010)
Iwakuma, T., Nemat-Nasser, S.: Finite elastic-plastic deformation of polycrystalline metals and composite. Proc. R. Soc. Lond. A 394, 87–119 (1984)
Liu, Y., Varghese, S., Ma, J., Yoshino, M., Lu, H., Komanduri, R.: Orientation effects in nanoindentation of single crystal copper. Int. J. Plast. 24, 11 (2008)
Lipinski, P., Berveiller, M.: Elastoplasticity of micro-inhomogeneous metals at large strains. Int. J. Plast. 5, 2 (1989)
Lipinski, P., Berveiller, M., Reubrez, E., Morreale, J.: Transition theories of elastic-plastic deformation of metallic polycrystals. Arch. Appl. Mech. 65, 291–311 (1995)
Hill, R.: Continuum micro-mechanics of elastoplastic polycrystals. J. Mech. Phys. Solids 13, 2 (1965)
Hill, R.: Continuum micro-mechanics of elastoplastic polycrystals. J. Mech. Phys. Solids 13, 2 (1965)
Hill, R.: A self-consistent mechanics of composite materials. J. Mech. Phys. Solids 13, 4 (1965)