Heat Generation Characteristics of LiFePO4 Pouch Cells with Passive Thermal Management
Tóm tắt
This article experimentally investigates the heat generation characteristics and the effectiveness of passive cooling of commercially available LiFePO4 (7.25 mm × 160 mm × 227 mm, 19.5 Ah) cells using different cooling materials. The specific heat capacity and the entropy coefficient of the cell are experimentally measured. The heat generation rate of the cell at 1–4 C current rates are also determined using three different methods: (1) the heat absorption calculated from the temperature increase of cooling water; (2) the energy loss calculated from the difference between the operating voltage and open circuit voltage; and (3) the energy loss during a charge-discharge cycle calculated using the voltage difference between charging and discharging. Results show that the heat generation rate estimated from heat absorbed by the water can be underestimated by up to 47.8% because of the temperature gradient within the cell and on the surface. The effectiveness of different passive cooling materials is compared at discharge current rates of 1–3 C. The average increase of the cell surface temperature is 22.6, 17.1, 7.7, 7.2 and 6.4 °C at 3 C (58.5 A) using air, aluminum foam, octadecane, water with aluminum foam and water, respectively.
Từ khóa
Tài liệu tham khảo
Optiz, 2017, Can Li-Ion batteries be the panacea for automotive applications?, Renew. Sustain. Energy Rev., 68, 685, 10.1016/j.rser.2016.10.019
Groot, 2015, On the complex ageing characteristics of high-power LiFePO4/graphite battery cells cycles with high charge and discharge currents, J. Power Sources, 286, 475, 10.1016/j.jpowsour.2015.04.001
Bernardi, 1985, A general energy balance for battery systems, J. Electrochem. Soc., 132, 5, 10.1149/1.2113792
Lin, 2015, Thermal analysis of large-capacity LiFePO4 power batteries for electric vehicles, J. Power Sources, 294, 633, 10.1016/j.jpowsour.2015.06.129
Takano, 2002, Entropy change in lithium ion cells on charge and discharge, J. Appl. Electrochem., 32, 251, 10.1023/A:1015547504167
Bandhauer, 2014, Temperature-dependent electrochemical heat generation in a commercial lithium-ion battery, J. Power Sources, 247, 618, 10.1016/j.jpowsour.2013.08.015
Forgez, 2010, Thermal modeling of a cylindrical LiFePO4/graphite lithium-ion battery, J. Power Sources, 195, 2961, 10.1016/j.jpowsour.2009.10.105
Drake, 2014, Measurement of anisotropic thermophysical properties of cylindrical Li-ion cells, J. Power Sources, 252, 298, 10.1016/j.jpowsour.2013.11.107
Yildiz, 2016, Modeling and validation of temperature changes in a pouch lithium-ion battery at various discharge rates, Int. Commun. Heat Mass Transf., 75, 311, 10.1016/j.icheatmasstransfer.2016.03.009
Chen, 2014, Measurement of heat generation in prismatic Li-ion batteries, J. Power Sources, 261, 28, 10.1016/j.jpowsour.2014.03.037
Chen, 2014, Accurate determination of battery discharge characteristics—A comparison between two battery temperature control methods, J. Power Sources, 247, 961, 10.1016/j.jpowsour.2013.09.060
Rostami, 2016, Numerical Studies of Lithium-ion Battery Thermal Management System Using Phase Change Materials and Metal Foams, Int. J. Heat Mass Transf., 102, 1159, 10.1016/j.ijheatmasstransfer.2016.07.010
Libeer, 2016, Two-phase heat and mass transfer of phase change materials in thermal management systems, Int. J. Heat Mass Transf., 100, 215, 10.1016/j.ijheatmasstransfer.2016.04.076
Zou, 2017, Electrothermal dynamics-conscious lithium-ion battery cell-level charging management via state-monitored predictive control, Energy, 141, 250, 10.1016/j.energy.2017.09.048
Zou, 2017, Electrochemical Estimation and Control for Lithium-Ion Battery Health-Aware Fast Charging, IEEE Trans. Ind. Electron., 65, 6635, 10.1109/TIE.2017.2772154
Panchal, 2016, Experimental and theoretical investigations of heat generation rates for a water-cooled LiFePO4 battery, Int. J. Heat Mass Transf., 101, 1093, 10.1016/j.ijheatmasstransfer.2016.05.126
Panchal, 2016, Thermal modeling and validation of temperature distributions in a prismatic lithium-ion battery at different discharge rates and varying boundary conditions, Appl. Therm. Eng., 96, 190, 10.1016/j.applthermaleng.2015.11.019
Bandhauer, 2011, A Critical Review of Thermal Issues in Lithium-Ion Batteries, J. Electrochem. Soc., 158, R1, 10.1149/1.3515880
Wang, 2017, The stagnant thermal conductivity of porous media predicted by the random walk theory, Int. J. Heat Mass Transf., 107, 520, 10.1016/j.ijheatmasstransfer.2016.11.069
Singh, 2004, Computational aspects of thermal conductivity of highly porous metal foams, Appl. Therm. Eng., 24, 1841, 10.1016/j.applthermaleng.2003.12.011
Kizilel, 2008, Passive control of temperature excursion and uniformity in high-energy Li-ion battery packs at high current and ambient temperature, J. Power Sources, 183, 370, 10.1016/j.jpowsour.2008.04.050
Yan, 2016, Experimental study on the application of phase change material in the dynamic cycling of battery pack system, Energy Convers. Manag., 128, 12, 10.1016/j.enconman.2016.09.058
Li, 2015, Experimental study of a passive thermal management system for high-powered lithium ion batteries using porous metal foam saturated with phase change materials, J. Power Sources, 255, 403
Sabbah, 2008, Active (air-cooled) vs. passive (phase change material) thermal management of high power lithium-ion packs: Limitation of temperature rise and uniformity of temperature distribution, J. Power Sources, 182, 630, 10.1016/j.jpowsour.2008.03.082