Guidelines for etching silicon MEMS structures using fluorine high-density plasmas at cryogenic temperatures
Tóm tắt
This paper presents guidelines for the deep reactive ion etching (DRIE) of silicon MEMS structures, employing SF/sub 6//O/sub 2/-based high-density plasmas at cryogenic temperatures. Procedures of how to tune the equipment for optimal results with respect to etch rate and profile control are described. Profile control is a delicate balance between the respective etching and deposition rates of a SiO/sub x/F/sub y/ passivation layer on the sidewalls and bottom of an etched structure in relation to the silicon removal rate from unpassivated areas. Any parameter that affects the relative rates of these processes has an effect on profile control. The deposition of the SiO/sub x/F/sub y/ layer is mainly determined by the oxygen content in the SF/sub 6/ gas flow and the electrode temperature. Removal of the SiO/sub x/F/sub y/ layer is mainly determined by the kinetic energy (self-bias) of ions in the SF/sub 6//O/sub 2/ plasma. Diagrams for profile control are given as a function of parameter settings, employing the previously published "black silicon method". Parameter settings for high rate silicon bulk etching, and the etching of micro needles and micro moulds are discussed, which demonstrate the usefulness of the diagrams for optimal design of etched features. Furthermore, it is demonstrated that in order to use the oxygen flow as a control parameter for cryogenic DRIE, it is necessary to avoid or at least restrict the presence of fused silica as a dome material, because this material may release oxygen due to corrosion during operation of the plasma source. When inert dome materials like alumina are used, etching recipes can be defined for a broad variety of microstructures in the cryogenic temperature regime. Recipes with relatively low oxygen content (1-10% of the total gas volume) and ions with low kinetic energy can now be applied to observe a low lateral etch rate beneath the mask, and a high selectivity (more than 500) of silicon etching with respect to polymers and oxide mask materials is obtained. Crystallographic preference etching of silicon is observed at low wafer temperature (-120/spl deg/C). This effect is enhanced by increasing the process pressure above 10 mtorr or for low ion energies (below 20 eV).
Từ khóa
#Plasma temperature #Guidelines #Etching #Silicon #Micromechanical devices #Plasma applications #Cryogenics #Kinetic energy #Optimal control #PassivationTài liệu tham khảo
10.1109/23.958741
van veenendaal, 2001, From an Atomistic to a continuum Description of Crystal Growth
10.1016/S0924-4247(00)00362-9
10.1149/1.2220767
10.1016/S0167-9317(96)00142-6
elwenspoek, 1998, Silicon Micromachining
10.1088/0960-1317/5/2/015
vugts, 0, Reaction Layer Dynamics in Silicon Etching
10.1116/1.580205
0
0
10.1116/1.588761
10.1063/1.348602
10.1109/MEMSYS.1996.493989
10.1016/S0026-2692(01)00039-8
10.1143/JJAP.30.3319
0
10.1016/S0039-6028(00)00479-9
10.1149/1.2056190
laermer, 0, Method of anisotropically etching silicon
10.1063/1.99382
frank, 1958, Growth and Perfection of Crystals, 411
bhardwaj, 1995, advanced silicon etching using high density plasmas, Proc SPIE-Micromachining Microfabrication Process Technology, 2639, 224, 10.1117/12.221279
10.1016/0167-9317(94)00144-J
francou, 1991, deep and fast plasma etching for silicon micromachining, Sens Actuators Phys A, 46–47, 17
10.1109/MEMSYS.1998.659807
10.1109/MEMSYS.1995.472573
10.1116/1.591054
10.1016/0039-6028(81)90106-0
10.1116/1.1313578
10.1063/1.99195
10.1063/1.350241
10.1007/978-3-642-59497-7_145
10.1016/0039-6028(86)90675-8
10.1116/1.586463