Comparative study on the friction behaviour of piston/bore interface technologies
Tóm tắt
Engine crank case designs for passenger car applications are based today on two main material technologies: grey cast iron and an increasing share of aluminium-based concepts. Due to the low wear resistance of aluminium, the latter concepts require a wear protective layer for the cylinder bore surface. Iron-based thermal spray coats are widely used for this purpose. The coating improves the tribological behaviour significantly, as previous studies have shown. Additionally, aluminium-based concepts offer advantages regarding engine weight and thermal management. The aim of the presented work was the discussion of these technological concepts regarding the tribological and sealing properties of the piston/bore interface. The study was carried out based on the AVL FRISC Floating Liner Engine. While the basic engine remained unchanged, the cylinder bore surface was varied. In addition to the floating liner friction measurement, the blow-by and lube oil consumption were also measured. A state-of-the-art multi-body dynamic simulation model complements the experimental study, while both simulation and measurement lead to similar conclusions.
Tài liệu tham khảo
citation_journal_title=J Mater Eng Perform; citation_title=Machinability of hypereutectic silicon–aluminum alloys; citation_author=T Tanaka, T Akasawa; citation_volume=08; citation_publication_date=1999; citation_pages=463-468; citation_doi=10.1361/105994999770346774; citation_id=CR1
citation_title=Überholung von Aluminium-Motorblöcken; citation_publication_date=2006; citation_id=CR2; citation_author=A Schäfer; citation_author=U Schilling; citation_author=S Schnaibel; citation_publisher=MSI Motor Service International GmbH
citation_journal_title=Motorentechnische Zeitschrift MTZ; citation_title=Lightweight design for cylinder blocks; citation_author=E Köhler; citation_volume=10; citation_publication_date=2009; citation_pages=4-12; citation_id=CR3
Schommers, J., et al.: Optimizing friction: the basis for safeguarding the combustion engines. 33rd International Vienna Motor Symposium, Wien (2012)
An, J.: Bestimmung der Schmierungs- und Reibungsverhältnisse im Kontakt Kolbenring gegen Zylinderlaufbahn von Verbrennungsmotoren in einem Modelltribometer, Dissertation, Ruhr-Universität Bochum, Bochum (2014)
Biberger, J.: Tribologisch induzierte Oberflächenveränderungen im Reib-Verschleiß-Kontakt Kolbenring gegen Zylinderlaufbahn, Dissertation, Technische Universität Berlin, Berlin (2017)
citation_journal_title=Tribologie und Schmierungstechnik; citation_title=Kombinierte Tribosystemanalyse des Kontaktes Kolben-, Ringpaket/Zylinderlaufbahn auf Basis von Floating Liner Untersuchungen; citation_author=J Edtmayer; citation_volume=65; citation_issue=4; citation_publication_date=2018; citation_pages=15-21; citation_id=CR7
citation_title=AVL FRISC Friction Analysis of Piston Group; citation_publication_date=2015; citation_id=CR8; citation_author=S Lösch; citation_publisher=ATZlive—Springer Vieweg
citation_journal_title=Motorentechnische Zeitrschrift MTZ; citation_title=The next generation gasoline engine family from BMW; citation_author=C Landerl, M Rülicke, D Spanring, S Schmuck-Soldan; citation_volume=03; citation_publication_date=2018; citation_pages=38-45; citation_id=CR9
Hick, H., et al.: Emissionsreduktion und Reibungs- und Verschleißverhalten. Reibung in Antrieb und Fahrzeug 2018—Springer Vieweg, Esslingen (2018)
Rauleder: Rauleder Aluminiumsandguss [Online].
https://www.rauleder.com/pdf/legierungen/226.pdf
. Zugriff am 30 Oct 2018 (2015)
European Standard: DIN EN 1706:2010-06, Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties; German version. Brussels (2010)
European Standard: DIN EN 1561:2012-01, Founding - Grey cast irons; German version. Brussels (2012)
Krause, S.: Massenspektrometrisches Verfahren zur Charakterisierung der Ölverdampfung im Brennraum von Ottomotoren. Dissertation, Technische Universität Hamburg-Harburg, Hamburg (2009)