Analytical procedures for design of strain softening and hardening cement composites

Springer Science and Business Media LLC - Tập 9 - Trang 181-194 - 2017
Yiming Yao1, Xinmeng Wang2, Karan Aswani3, Barzin Mobasher1
1School of Sustainable Engineering and Built Environment, Arizona State University, Tempe, USA
2DiGioia Gray & Associates, Tempe, USA
3PK Associates, Scottsdale, USA

Tóm tắt

Fiber reinforced concrete (FRC) can be designed to exhibit pronounced ductility, energy absorption capacity, post-cracking strength depending on the fiber type and volume fraction. FRC have been classified into two categories, namely, strain softening and strain hardening cement composites (SSCC and SHCC). SSCC and SHCC are ultra-ductile class of materials developed for applications in the large material volume usage in the cost sensitive construction industry. Strain hardening behavior can be obtained by adding relatively low volume (typically <2%) of randomly distributed fibers and demonstrates a well formed distributed crack system. Mechanical properties under uniaxial tensile, flexural, and shear tests indicate superior performance such as tensile strength as high as 25 MPa, and strain capacity of 1–8%. Development of proper design and analysis tools are very essential to fully utilize these materials. Several approaches are presented in this paper for analysis, simulation, back-calculation, and design of strain softening and strain hardening cement composite systems, and are applicable to all classes of SSCC and SHCC such as steel fiber reinforced concrete, textile reinforced concrete, and ultra-high performance fiber reinforced concrete.

Tài liệu tham khảo

Destrée, X., Yao, Y., Mobasher, B.: Sequential cracking and their openings in steel-fiber-reinforced joint-free concrete slabs. J. Mater. Civ. Eng. 28(4), 04015158 (2015). doi:10.1061/(ASCE)MT.1943-5533.0001377

Mobasher, B.: Mechanics of Fiber and Textile Reinforced Cement Composites. CRC Press, Boca Raton (2011)

Yao, Y., Silva, F.A., Butler, M., Mechtcherine, V., Mobasher, B.: Tension stiffening in textile-reinforced concrete under high speed tensile loads. Cem. Concr. Compos. 64, 49–61 (2015)

Mobasher, B., Dey, V., Cohen, Z., Peled, A.: Correlation of constitutive response of hybrid textile reinforced concrete from tensile and flexural tests. Cem. Concr. Compos. 53, 148–161 (2014)

Mobasher, B., Peled, A., Pahilajani, J.: Distributed cracking and stiffness degradation in fabric-cement composites. Mater. Struct. 39, 317–331 (2006)

Mobasher, B., Pahilajani, J., Peled, A.: Analytical simulation of tensile response of fabric reinforced cement based composites. Cem. Concr. Compos. 28, 77–89 (2006)

Soranakom, C., Mobasher, B.: Flexural analysis and design of textile reinforced concrete. In: 4th Colloquium on Textile Reinforced Structures (CTRS4), Dresden, Germany June 3–5 (2009)

Soranakom, C., Mobasher, B.: Correlation of tensile and flexural responses of strain softening and strain hardening cement composites. Cem. Concr. Compos. 30, 465–477 (2008)

Soranakom, C., Mobasher, B.: Closed-Form moment–curvature expressions for homogenized fiber-reinforced concrete. Mater. J. 104, 351–359 (2007)

Soranakom, C., Mobasher, B.: Closed-form solutions for flexural response of fiber-reinforced concrete beams. J. Eng. Mech. 133, 933–941 (2007)

Mobasher, B., Yao, Y., Soranakom, C.: Analytical solutions for flexural design of hybrid steel fiber reinforced concrete beams. Eng. Struct. 100, 164–177 (2015)

ACI Committee 318, American Concrete Institute: building code requirements for structural concrete (ACI 318-14): an ACI standard: commentary on building code requirements for structural concrete (ACI 318R-14), an ACI report. (2014)

Johansen, K.W.: Yield-Line Theory. Cement and Concrete Association, London (1962)

Johansen, K.W.: Yield-Line Formulae for Slabs. Cement and Concrete Association, London (1972)

Kennedy, G., Goodchild, C.: Practical Yield Line Design. The Concrete Centre, Riverside house (2004)

Wang, X., Subramaniam: Analytical load-deflection equations for beam and 2-D panel with a bilinear moment–curvature model. In: ASU Electronic Dissertations and Theses. Arizona State University (2015)

Yao, Y., Aswani, K., Wang, X., Mobasher, B.: Analytical displacement solutions for statically determinate beams based on a trilinear moment–curvature model. J. Struct. Eng. (Under review)

Wang, X.: Analytical Load-deflection equations for beam and 2-D panel with a bilinear moment–curvature model. http://gradworks.umi.com/15/95/1595325.html, (2015)

Aswani, K.: Design procedures for strain hardening cement composites (SHCC) and measurement of their shear properties by mechanical and 2-D digital image correlation (DIC) method. http://adsabs.harvard.edu/abs/2014PhDT……..23A, (2014)

Bakhshi, M., Barsby, C., Mobasher, B.: Comparative evaluation of early age toughness parameters in fiber reinforced concrete. Mater. Struct. 47, 853–872 (2014)

Darwin, D., Dolan, C., Nilson, A.: Design of concrete structures. McGraw-Hill Education, New York (2015)

Kim, J., Kim, D.J., Park, S.H., Zi, G.: Investigating the flexural resistance of fiber reinforced cementitious composites under biaxial condition. Compos. Struct. 122, 198–208 (2015)

Khaloo, A.R., Afshari, M.: Flexural behaviour of small steel fibre reinforced concrete slabs. Cem. Concr. Compos. 27, 141–149 (2005)

Sawyer Jr., H.A.: Design of concrete frames for two failure stages. Spec. Publ. 12, 405–437 (1965)

de Montaignac, R., Massicotte, B., Charron, J.-P., Nour, A.: Design of SFRC structural elements: post-cracking tensile strength measurement. Mater. Struct. 45, 609–622 (2012)

Thông tin
Thông tin xuất bản

Springer Science and Business Media LLC

Tập 9

181-194

Thông tin tác giả