An investigation on the effect of diamond concentration and matrix material composition in the circular sawing process of granites

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science - Tập 225 Số 1 - Trang 17-27 - 2011
İrfan Ucun1, Kubilay Aslantaş1, I.S. Buyuksagis2, Süleyman Taşgeti̇ren1
1Department of Mechanical Education, University of Afyon Kocatepe, Afyonkarahisar, Turkey
2Department of Marble Technology, University of Afyon Kocatepe, Afyonkarahisar, Turkey

Tóm tắt

In the process of natural stone cutting, segmented circular diamond saw blades are widely used in the sawing process of granites. Generally, copper, cobalt, or a combination of these is used as the matrix material. The diamond particle used in segments is added to the matrix material in certain rates and sizes. In this article, the effect of tungsten, cobalt, copper, and tin elements, which are added to the matrix material, on the cutting performance was studied. In addition, in order to study the effect of diamond concentration, the segments with different diamond concentration were manufactured. Using these segments, cutting experiments for granite, which are known as natural hard stones, are conducted. In the cutting experiments, peripheral speed of the cutting disc, cutting speed, and depth cut were taken as constant. After the experiments, cutting forces, power consumption, and specific energy changes for each segment were determined. On the other hand, the status of damage and wear for the surfaces of each segment during the cutting process was evaluated in terms of segment performances. According to the results, an increase in diamond concentration results in a lower cutting force and power consumption and also causes a lower specific wear of the segment.

Từ khóa


Tài liệu tham khảo

10.1016/j.jmatprotec.2006.10.034

Asche J., 1991, Ind. Diam. Rev., 2, 110

10.1023/A:1019189908172

10.1016/S0167-577X(02)00915-1

10.4028/www.scientific.net/KEM.250.181

10.1016/S0924-0136(03)00236-X

10.4028/www.scientific.net/KEM.250.187

10.4028/www.scientific.net/MSF.471-472.292

Rosa G. L., 2002, Ind. Diam. Rev., 1, 45

10.1007/s10913-005-0089-x

10.4028/www.scientific.net/KEM.315-316.185

10.4028/www.scientific.net/MSF.532-533.321

Tönshoff H. K., 1991, Ind. Diam. Rev., 3, 198

10.1016/0148-9062(85)93229-2

10.1016/S0301-679X(01)00039-1

Asche J., 2000, Tiefschleifen von Granit

10.1111/j.1460-2695.2008.01232.x

Ucun I., 2002, Electron. J. Mach. Technol., 5, 33

10.4028/www.scientific.net/MSF.534-536.1113

Karagöz Ş., 2002, Mater. Des., 28, 1055

10.1016/S0263-4368(00)00043-3

10.1016/j.ijrmms.2006.07.008

10.4028/www.scientific.net/KEM.202-203.293

10.4028/www.scientific.net/KEM.202-203.349

10.4028/www.scientific.net/KEM.259-260.106

10.1080/10426910903344039

Thông tin
Thông tin xuất bản

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science

Tập 225 Số 1

17-27

Thông tin tác giả