Residual stresses in selective laser sintering and selective laser melting

Emerald - Tập 12 Số 5 - Trang 254-265 - 2006
Peter Mercelis1, Jean‐Pierre Kruth1
1Division PMA, Department of Mechanical Engineering, University of Leuven, Leuven, Belgium

Tóm tắt

PurposeThis paper presents an investigation into residual stresses in selective laser sintering (SLS) and selective laser melting (SLM), aiming at a better understanding of this phenomenon.Design/methodology/approachFirst, the origin of residual stresses is explored and a simple theoretical model is developed to predict residual stress distributions. Next, experimental methods are used to measure the residual stress profiles in a set of test samples produced with different process parameters.FindingsResidual stresses are found to be very large in SLM parts. In general, the residual stress profile consists of two zones of large tensile stresses at the top and bottom of the part, and a large zone of intermediate compressive stress in between. The most important parameters determining the magnitude and shape of the residual stress profiles are the material properties, the sample and substrate height, the laser scanning strategy and the heating conditions.Research limitations/implicationsAll experiments were conducted on parts produced from stainless steel powder (316L) and quantitative results cannot be simply extrapolated to other materials. However, most qualitative results can still be generalized.Originality/valueThis paper can serve as an aid in understanding the importance of residual stresses in SLS/SLM and other additive manufacturing processes involving a localized heat input. Some of the conclusions can be used to avoid problems associated with residual stresses.

Tài liệu tham khảo

Aggarangsi, P. and Beuth, J. (2003), “Melt pool size and stress control for laser‐based deposition near a free edge”, Proceedings of the Solid Freeform Fabrication Symposium, pp. 196‐207. Kruth, J. and Bleys, P. (2000), “Measuring residual stress caused by wire EDM of tool steel”, International Journal of Electrical Machining, Vol. 5, pp. 23‐8. Kruth, J., Froyen, L., Rombouts, M., van Vaerenbergh, J. and Mercelis, P. (2003), “New ferro powder for selective laser sintering of dense parts”, Annals of the CIRP, pp. 139‐42. Kruth, J., Mercelis, P., Froyen, L. and Rombouts, M. (2004), “Binding mechanisms in selective laser sintering and selective laser melting”, Proceedings of the Solid Freeform Fabrication Symposium, pp. 44‐59. Nowell, D., Hills, D. and Tochilin, S. (2000), “Use of the crack compliance method for the measurement of residual stress”, Proceedings of the 6th International Conference on Residual Stresses, Vol. 2, pp. 845‐52. Over, C. (2003), “Generative Fertigung von Bauteilen aus Werkzeugstahl X38CrMoV5‐1 und Titan TiAl6V4 mit Selective Laser Melting”, PhD thesis, RWTH Aachen. Prime, M. (1999), “Residual stress measurement by seccessive extension of a slot: the crack compliance method”, Applied Machanics Reviews, Vol. 52 No. 2, pp. 75‐96. Schindler, H. (2000), “Residuals stress measurements in cracked components: capabilities and limitations of the cut compliance method”, Materials Science Forum, Vol. 347‐349, pp. 150‐5. Vasinonta, A., Beuth, J. and Griffith, M. (2000), “Process maps for controlling residual stress and melt pool size in laser‐based sff processes”, Proceedings of the Solid Freeform Fabrication Symposium, pp. 200‐8. Withers, P. and Bhadeshia, H. (2001), “Residual stress, part 2 ‐nature and origin”, Materials Science and Technology, Vol. 17, pp. 366‐75.
Thông tin
Thông tin xuất bản

Emerald

Tập 12 Số 5

254-265

Thông tin tác giả