Varying bending eigenfrequencies in BTA deep hole drilling: mechanical modeling using statistical parameter estimation
Tóm tắt
One serious problem in deep-hole drilling is the formation of a dynamic disturbance called spiralling which causes a multi-lobe shaped distortion of the bore hole cross section. An important factor governing the occurrence of spiralling is the coincidence of a bending eigenfrequency of the boring tool with a multiple of the spindle rotation frequency. This article presents a discrete dynamic model of the tool/boring-bar assembly including a Lanchester-damper and containing free parameters for the unknown stiffness of the tools lateral supports. Furthermore, a method for estimating these parameters by determining the changing eigenfrequencies over the drilling depth from spectrogram data using the maximum likelihood method is proposed.
Tài liệu tham khảo
N. N. (2006) VDI-Richtlinie 3210 Blatt 1: Tiefbohrverfahren/Deep-hole drilling. Beuth Verlag GmbH, Berlin
Heisel U, Storchak M, Eissler R (2003) Determination of cutting parameters with deep hole drilling with single-fluted gun drills of smallest diameters. Production engineering—research and development Ann German Acad Soc Prod Eng X(1):51–54
Weinert K, Webber O, Busse A, Hüsken M, Mehnen J, Stagge P (2001) Experimental investigation of the dynamics of the BTA deep hole drilling process. Production engineering—research and development Ann German Acad Soc Prod Eng VIII(2):1–4
Weinert K, Webber O, Gepperth A, Zhang Y, Theis W (2004) Time varying process dynamics in BTA deep hole drilling. In: Teti R (ed) Proceedings of the 4th CIRP international seminar on intelligent computation in manufacturing engineering, ICME 2004, Sorrento, Naples, pp 419–424
Weinert K, Webber O, Peters C (2005) On the influence of drilling depth dependent modal damping on chatter vibration in BTA deep hole drilling. Ann CIRP 54(1):363–366
Gessesse YB, Latinovic VN (1991) Effect of the stuffing box on boring bar vibrations. Int J Prod Res 20(3):565–574
Gessesse YB, Latinovic VN, Osman MOM (1994) On the problem of spiralling in BTA deep hole machining. J Eng Ind Trans ASME 116:161–194
Stockert R (1978) Beitrag zur optimalen Auslegung von Tiefbohrwerkzeugen. Dissertation, University of Dortmund
Streicher P (1975) Tiefbohren der Metalle. WI-Fachbuchreihe, Vogel-Verlag, Würzburg
Pfleghar F (1975) Zur Entstehung von unrunden Bohrungen beim Arbeiten mit einschneidigen Tiefbohrwerkzeugen. TZ für praktische Metallbearbeitung 69(12):389–393
Chin JH, Hsieh CT, Lee LW (1996) The shaft behaviour of BTA deep hole drilling tool. Int J Mech Sci 38(5):461–482
Chin JH, Lee LW (1995) A study on the eigenproperties of a BTA deep hole drill—theorie and experiments. Int J Mach Tools Manuf 35(1):29–49
Deng CS, Chin JH (2004) Roundness errors in BTA drilling and a model of waviness and lobing caused by resonant forced vibrations of its long drill shaft. J Manuf Sci Eng Trans ASME 126:524–534
Perng YL, Chin JH (1999) Theoretical and experimental investigations on the spinning BTA deep hole drill shafts containing fluids and subject to axial forces. Int J Mech Sci 41:1301–1322
Al-Wedyan HM (2004) Control of whirling vibrations in BTA deep hole boring process using fuzzy logic modeling and active suppression technique. Dissertation, Concordia University, Montreal
Raabe N, Webber O, Theis W (2004) Spiralling in BTA deep hole drilling—how to model varying frequencies. In: 4th annual meeting of the European network for buisiness and industrial statitics (ENBIS). Kopenhagen, Denmark, pp 20–22
Ewins DJ (2000) Modal testing—theory, practice and application, 2nd edn. Research Studies Press Ltd., Baldock
Nelder JA, Mead R (1965) A simplex method for functional minimization. Comput J 7:308–331
Hartung J, Elpelt B, Klösener K-H (2002) Statistik. Oldenbourg Verlag, München
Schlittgen R, Streitberg BHJ (1999) Zeitreihenanalyse. Oldenbourg Verlag, München