Three-dimensional turbulent swirling flow in a cylinder: Experiments and computations

Choudhury, D., 1993. Introduction to Renormalization Group Method and Turbulence Modeling. Fluent Inc. Technical Memorandum TM-107. Durst, 1991, Numerical aspects of calculation of confined swirling flows with internal recirculation, Int. J. Numer. Methods Fluids, 12, 203, 10.1002/fld.1650120302 Hedlund, 2000, Local swirl chamber heat transfer and flow structure at different Reynolds numbers, Trans. ASME J. Turbomach., 122, 375, 10.1115/1.555458 Imaichi, 1983, Numerical processing of flow visualization pictures – measurement of two-dimensional vortex flow, J. Fluid Mech., 129, 283, 10.1017/S0022112083000774 Jakirilić, 2002, Modeling rotating and swirling turbulent flows: a perpetual challenge, AIAA J., 40, 1984, 10.2514/2.1560 Khalighi, B., 1989. Study of the intake swirl process in an engine using flow visualization and particle tracking velocimetry. In: Flow Visualization, FED-vol. 85, ASME Winter Annual Meeting, San Francisco, pp. 37–47. Khalighi, 1989, Particle tracking velocimetry: an automatic image processing algorithm, Appl. Opt., 28, 4328, 10.1364/AO.28.004328 Kumar, 1993, Flow visualization studies of a swirling flow in a cylinder, J. Exp. Thermal Fluid Sci., 7, 254, 10.1016/0894-1777(93)90009-8 Launder, 1974, The numerical computation of turbulent flows, Comput. Methods Appl. Mech. Eng., 3, 269, 10.1016/0045-7825(74)90029-2 Legrand, 2000, Analysis of wall turbulence in swirling annular decaying flow induced by a tangential fluid inlet, Can. J. Phys., 78, 779, 10.1139/p00-052 Mikulec, 1988, Effects of intake port configuration on induction-generated swirl in a piston engine: a water analog experiment using particle tracking velocimetry Neto, 1998, Finite-element simulation of laminar swirling decaying flow induced by means of a tangential inlet in an annulus, Comput. Methods Appl. Mech. Eng., 165, 189, 10.1016/S0045-7825(98)00040-1 Pan, Y., 1992. Numerical study of a three-dimensional swirling flow in a cylinder. M.S. Thesis. Mechanical Engineering, Clemson University. Parks, S.M., Oluwole, O., Wehbe, W.I., Olson, T.J., Petty, C.A., 2002. The influence of hydrocyclone geometry on separation performance. In: Proceedings of Minerals Engineering Conference on Solid–Liquid Separation, Falmouth, UK, June 18–20. Patankar, 1980 Pettersson, 1998, Modeling near-wall effects in axially rotating pipe flow by elliptic relaxation, AIAA J., 36, 1164, 10.2514/2.527 Sharif, M.A.R., Busnaina, A.A., 1988. Modeling of three-dimensional swirling flow in cylindrical configurations. In: Tippins, V.A., Patton, E.M. (Eds.), Proceedings of the ASME International Computers in Engineering Conference, San Francisco, California, vol. 3, pp. 455–463. Svarovsky, 1985, Solid–liquid separation processes and technology, vol. 5 Walter, J.A., 1989. Development of a quantitative velocity imaging system and its application to offset channel flow. M.S. Thesis. Mechanical Engineering, University of Iowa. Yakhot, 1986, Renormalization group analysis of turbulence, J. Sci. Comput., 1 Yang, 2003, Computation of strongly swirling confined flows with cubic eddy-viscosity turbulence models, Int. J. Numer. Methods Fluids, 43, 1355, 10.1002/fld.565