Surface roughness and cutting forces modeling for optimization of machining condition in finish hard turning of AISI 52100 steel
Tóm tắt
Từ khóa
Tài liệu tham khảo
T. Hodgson, P. Trendler and G. Ravignani, Turning hardened tool steels with cubic boron nitride inserts, Ann. CIRP. 30 (1981) 63–66.
N. Narutaki, Y. Yamane and K. Okushima, Tool wear and cutting temperature of CBN tool in machining of hardened steels, Ann. CIRP. 28 (1979) 23–28.
X. L. Liu, D. H. Wen, Z. J. Li, L. Xiao and F. G. Yan, Experimental study on hard turning hardened GCr15 steel with PCBN tool, J. Mater. Process. Technol. 129 (2002) 217–221.
R. Pavel, I. Marinescu and M. Deis, J. Pillar, Effect of tool wear on surface finish for a case of continuous and interrupted hard turning, J. Mater. Process. Technol. 170 (2005) 341–349.
T. Özel, T. K. Hsu and E. Zeren,, Effects of cutting edge geometry, workpiece hardness, feed rate and cutting speed on surface roughness and forces in finish turning of hardened AISI H13 steel, Int. J. Adv. Manuf. Technol. 25 (2005) 262–269.
S. Y. Luo, Y. S. Liao and Y. Y. Tsai, Wear characteristics turning high hardness alloy steel by ceramic and CBN tools, J. Mater. Process. Technol. 88 (1999) 114–121.
M. Remadna and J. F. Rigal, Evolution during time of tool wear and cutting forces in the case of hard turning with CBN inserts, J. Mater. Proc. Technol. 178 (2006) 67–75.
T. Sornakumar, M. V. Gopalakrishnan, R. Krishnamurthy and C. V. Gokularatnam, Development of alumina and Ce-TTZ ceramic composite (ZTA) cutting tool, Int. J. Refract. Metals. Hard. Mater. 13 (1995) 375–378.
D. I. Lalwani, N. K. Mehta and P. K. Jain, Experimental investigations of cutting parameters influence on cutting forces and surface roughness in finish hard turning of MDN250 steel, J. Mater. Process. Technol. 206 (2008) 167–179.
K. Nakayama, M. Arai and T. Kanda, Machining characteristics of hard materials, Ann. CIRP. 37 (1988) 89–92.
M. A. Yallese, K. Chaoui, N. Zeghib, L. Boulanouar and J. F. Rigal, Hard machining of hardened bearing steel using cubic boron nitride tool, J. Mater. Process. Technol. 209 (2009) 1092–1104.
H. Aouici, M. A. Yallese, B. Fnides, K. Chaoui and T. Mabrouki, Modeling and optimization of hard turning of X38CrMoV5-1 steel with CBN tool: Machining parameters effects on flank wear and surface roughness, Journal of Mechanical Science and Technology 25(11) (2011) 2843–2851.
W. König, R. Komanduri, H. Tönshoff and G. Ackershott, Machining of hard materials, Ann. CIRP. 33 (1984) 417–428
V. N. Gaitonde, S. R. Karnik, L. Figueira and J. P. Davim, Machinability investigations in hard turning of AISI D2 cold work tool steel with conventional and wiper ceramic inserts, Int. J. Refract. Metals. Hard. Mater. 27 (2009) 754–763.
A. K. Basim and M. Bashir, Study of cutting speed on surface roughness and chip formation when machining nickelbased alloy, Journal of Mechanical Science and Technology 24(5) (2010) 1083–1090.
Y. K. Chou and H. Song, Tool nose radius effects on finish hard turning, J. Mater. Process. Technol. 148 (2004) 259–268.
C. M. Lee, Surface roughness and cutting force prediction in MQL and wet turning process of AISI 1045 using design of experiments, Journal of Mechanical Science and Technology 24(8) (2010) 1669–1677.
J. H. Jung and W. T. Kwon, Optimization of EDM process for multiple performance characteristics using Taguchi method and Grey relational analysis, Journal of Mechanical Science and Technology 24(5) (2010) 1083–1090.
M. S. Phadke, Quality engineering using robust design, Englewood Cliffs, New Jersey (1989).
P. J. Ross, Taguchi techniques for quality engineering, New York (1988).
J. D. Thiele, S. N. Melkote, Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel, J. Mater. Process. Technol. 94 (1999) 216–226.
H. A. Kishawy, M. A. Elbestawi, Effects of process parameters on material side flow during hard turning, Int. J. Mach. Tools. Manuf. 39 (1999) 1017–1030.
D. C. Montgomery, Design and analysis of experiments, 5 ed., John Wiley & Sons Inc, New York (2001).
R. H. Myers and D. C. Montgomery, Response Surface Methodology: Process and Product Optimization Using Designed Experiments, 2nd ed., John Wiley and Sons, Inc.: New York (2002).