Surface integrity evolution of machined NiTi shape memory alloys after turning process
Tóm tắt
Owing to their shape memory effect and pseudoelasticity, NiTi shape memory alloys (SMAs) are widely used as functional materials. Mechanical processes particularly influence the final formation of the product owing to thermal softening and work-hardening effects. Surface integrity is an intermediate bridge between the machining parameter and performance of the product. In this study, experiments were carried out on turning NiTi SMAs at different cutting speeds, where surface integrity characteristics were analyzed. The results show that a higher cutting speed of 125 m/min is required to turn NiTi SMAs based on the evaluation of surface integrity. The degree of work hardening is higher at 15 m/min. Consequently, as a primary effect, work hardening appears on the plastic deformation of the machined samples, leading to dislocations and defects. As the cutting speed increases, the thermal softening effect exceeds work hardening and creates a smoother surface. A stress-induced martensitic transformation is considered during the turning process, but this transformation is reversed to an austenite from the X-ray diffraction (XRD) results. According to the differential scanning calorimetry (DSC) curves, the phase state and phase transformation are less influenced by machining. Subsequently, the functional properties of NiTi-SMAs are less affected by machining.
Tài liệu tham khảo
Bil C, Massey K, Abdullah EJ (2013) Wing morphing control with shape memory alloy actuators. J Intell Mater Syst Struct 24:879–898
Petrini L, Migliavacca F (2011) Biomedical applications of shape memory alloys. J Metall. https://doi.org/10.1155/2011/501483
Kaya E, Kaya İ (2020) Tool wear progression of PCD and PCBN cutting tools in high speed machining of NiTi shape memory alloy under various cutting speeds. Diam Relat Mater. https://doi.org/10.1016/j.diamond.2020.107810
Hope J, McDaid A (2017) Development of wearable wrist and forearm exoskeleton with shape memory alloy actuators. J Intell Robot Syst Theory Appl 86:397–417
Nematollahi M, Baghbaderani KS, Amerinatanzi A et al (2019) Application of NiTi in assistive and rehabilitation devices: a review. Bioeng. https://doi.org/10.3390/bioengineering6020037
Jayachandran S, Akash K, Mani Prabu SS et al (2019) Investigations on performance viability of NiTi, NiTiCu, CuAlNi and CuAlNiMn shape memory alloy/Kapton composite thin film for actuator application. Compos Part B Eng 176:107182. https://doi.org/10.1016/j.compositesb.2019.107182
Mehrpouya M, Bidsorkhi HC (2017) MEMS applications of NiTi based shape memory alloys: a review. Micro Nanosyst 8:79–91
Hsieh SF, Hsue AWJ, Chen SL et al (2013) EDM surface characteristics and shape recovery ability of Ti35.5Ni48.5Zr16 and Ni60Al 24.5Fe15.5 ternary shape memory alloys. J Alloys Compd 571:63–68
Pfeifer R, Herzog D, Hustedt M et al (2010) Pulsed Nd:YAG laser cutting of NiTi shape memory alloys—influence of process parameters. J Mater Process Technol 210:1918–1925
Kong MC, Srinivasu D, Axinte D et al (2013) On geometrical accuracy and integrity of surfaces in multi-mode abrasive waterjet machining of NiTi shape memory alloys. CIRP Ann Manuf Technol 62:555–558
Kaynak Y, Huang B, Karaca HE et al (2017) Surface characteristics of machined NiTi shape memory alloy: the effects of cryogenic cooling and preheating conditions. J Mater Eng Perform 26:3597–3606
Weinert K, Petzoldt V, Kötter D (2004) Turning and drilling of NiTi shape memory alloys. CIRP Ann Manuf Technol 53:65–68
Wang G, Liu Z, Niu J et al (2019) Work hardening influencing on shape memory effect of NiTi alloy by varying milling speeds. Smart Mater Struct. https://doi.org/10.1088/1361-665X/ab3de2
Elahinia M, Shayesteh MN, Taheri AM et al (2016) Fabrication of NiTi through additive manufacturing: a review. Prog Mater Sci 83:630–663
Mehrpouya M, Gisario A, Elahinia M (2018) Laser welding of NiTi shape memory alloy: a review. J Manuf Process 31:162–186
Huang H, Zheng HY, Liu Y (2005) Experimental investigations of the machinability of Ni50.6Ti49.4 alloy. Smart Mater Struct. https://doi.org/10.1088/0964-1726/14/5/019
Kaynak Y, Karaca HE, Noebe RD et al (2013) Tool-wear analysis in cryogenic machining of NiTi shape memory alloys: a comparison of tool-wear performance with dry and MQL machining. Wear 306:51–63
Hassan MR, Mehrpouya M, Dawood S (2014) Review of the machining difficulties of nickel-titanium based shape memory alloys. Appl Mech Mater 564:533–537
Wu SK, Lin HC, Chen CC (1999) Study on the machinability of a Ti49.6Ni50.4 shape memory alloy. Mater Lett 40:27–32
Weinert K, Petzoldt V (2004) Machining of NiTi based shape memory alloys. Mater Sci Eng A 378:180–184
Guo Y, Klink A, Fu C et al (2013) Machinability and surface integrity of nitinol shape memory alloy. CIRP Ann Manuf Technol 62:83–86
Wang G, Liu Z, Ai X et al (2018) Effect of cutting parameters on strain hardening of nickel-titanium shape memory alloy. Smart Mater Struct. https://doi.org/10.1088/1361-665X/aac43d
Zainal AZ, Tarisai MP, Harrison G (2020) Chilled air system and size effect in micro-milling of nickel-titanium shape memory alloys. Int J Precis Eng Manuf Green Technol 7:283–297
Liu JF, Li L, Guo YB (2014) Surface integrity evolution from main cut to finish trim cut in W-EDM of shape memory alloy. Procedia CIRP 13:137–142
Huang TS, Hsieh SF, Chen SL et al (2015) Surface modification of TiNi-based shape memory alloys by dry electrical discharge machining. J Mater Process Technol 221:279–284
Zhao Y, Li J, Guo K et al (2020) Study on chip formation characteristics in turning NiTi shape memory alloys. J Manuf Process 58:787–795
Mehrpouya M, Shahedin AM, Daood SDS et al (2017) An investigation on the optimum machinability of NiTi based shape memory alloy. Mater Manuf Process 32:1497–1504
Dash B, Das M, Das M et al (2019) A concise review on machinability of NiTi shape memory alloys. Mater Today Proc 18:5141–5150
Ulutan D, Ozel T (2011) Machining induced surface integrity in titanium and nickel alloys: a review. Int J Mach Tools Manuf 51:250–280
Deltombe R, Kubiak KJ, Bigerelle M (2014) How to select the most relevant 3D roughness parameters of a surface. Scanning 36:150–160
Sivalingam V, Sun J, Yang B et al (2018) Machining performance and tool wear analysis on cryogenic treated insert during end milling of Ti-6Al-4V alloy. J Manuf Process 36:188–196
Thakur A, Mohanty A, Gangopadhyay S (2014) Comparative study of surface integrity aspects of Incoloy 825 during machining with uncoated and CVD multilayer coated inserts. Appl Surf Sci 320:829–837
Dhar NR, Kamruzzaman M (2007) Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition. Int J Mach Tools Manuf 47:754–759
Thakur A, Gangopadhyay S (2016) State-of-the-art in surface integrity in machining of nickel-based super alloys. Int J Mach Tools Manuf 100:25–54
Arunachalam RM, Mannan MA, Spowage AC (2004) Surface integrity when machining age hardened Inconel 718 with coated carbide cutting tools. Int J Mach Tools Manuf 44:1481–1491
Zou B, Chen M, Huang C et al (2009) Study on surface damages caused by turning NiCr20TiAl nickel-based alloy. J Mater Process Technol 209:5802–5809
Kaynak Y, Karaca HE, Jawahir IS (2014) Surface integrity characteristics of NiTi shape memory alloys resulting from dry and cryogenic machining. Procedia CIRP 13:393–398
Kaynak Y (2014) Machining and phase transformation response of room-temperature austenitic NiTi shape memory alloy. J Mater Eng Perform 23:3354–3360
Wang G, Liu Z, Niu J et al (2020) Effect of electrochemical polishing on surface quality of nickel-titanium shape memory alloy after milling. J Mater Res Technol 9:253–262
Kaynak Y, Tobe H, Noebe RD et al (2014) The effects of machining on the microstructure and transformation behavior of NiTi alloy. Scr Mater 74:60–63
Miller DA, Lagoudas DC (2000) Thermomechanical characterization of NiTiCu and NiTi SMA actuators: influence of plastic strains. Smart Mater Struct 9:640–652
Arunachalam RM, Mannan MA, Spowage AC (2004) Residual stress and surface roughness when facing age hardened Inconel 718 with CBN and ceramic cutting tools. Int J Mach Tools Manuf 44:879–887