Study on machinability of in situ Al–4.5%Cu–TiC metal matrix composite-surface finish, cutting force prediction using ANN

Koczak, 1993, Metal Matrix Composites for Ground Vehicle, Aerospace, and Industrial Applications, 297 Tjong, 2000, Microstructural and Mechanical Characteristics of In Situ Metal Matrix Composites, Materials Science and Engineering Reports, 29, 49, 10.1016/S0927-796X(00)00024-3 Kennedy, 2001, Reaction in Al–TiC Metal Matrix Composites, Materials Science and Engineering A, A, 316 Bandyopadhyay, 2007, New Generation Metal Matrix Composites, Materials and Manufacturing Processes, 22, 679, 10.1080/10426910701384872 Daniel, 1997, Metal–ceramic Composites Via In Situ Methods, Journal of Materials Processing Technology, 68, 132, 10.1016/S0924-0136(96)00020-9 Miracle, 2005, Metal Matrix Composites from Science to Technological Significance, Composites Science and Technology, 65, 2526, 10.1016/j.compscitech.2005.05.027 Lee, 2005, Reaction Products of Al/TiC Composites Fabricated by the Pressure Less Infiltration Technique, Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 36, 2517, 10.1007/s11661-005-0125-0 Mukherjee, 2006, A Review of Optimization Techniques in Metal Cutting Processes, Computers & Industrial Engineering, 50, 15, 10.1016/j.cie.2005.10.001 Ozcatalbas, 2003, Investigation of the Machinability Behaviour of Al4C3 Reinforced Al-based Composite Produced by Mechanical Alloying Technique, Composites Science and Technology, 63, 53, 10.1016/S0266-3538(02)00177-X Ibrahim, 1991, Journal of Materials Science, 26, 1137, 10.1007/BF00544448 Rai, 2004, High Temperature Synthesis and Characterization of Al–TiC Composites to Commercialize for Foundry Practice, 1339 Manna, 2005, Influence of Machining Parameters on the Machinability of Particulate Reinforced Al/SiC–MMC, International Journal of Advanced Manufacturing Technology, 25, 850, 10.1007/s00170-003-1917-2 Ciftci, 2004, Evaluation of Tool Wear When Machining SiCp-reinforced Al-2014 Alloy Matrix Composites, Materials and Design, 25, 251, 10.1016/j.matdes.2003.09.019 Chambers, 1996, The Machinability of Light Alloy MMCs, Composites A: Applied Science and Manufacturing, 27A, 143, 10.1016/1359-835X(95)00001-I Looney, 1992, The Turning of an A1/SiC Metal–matrix Composite, Journal of Materials Processing Technology, 33, 453, 10.1016/0924-0136(92)90279-2 El-Gallab, 1998, Machining of Al:SiC Particulate Metal–matrix Composites Part I: Tool Performance, Journal of Materials Processing Technology, 83, 151, 10.1016/S0924-0136(98)00054-5 Ding, 2005, Evaluation of Machining Performance of MMC with PCBN and PCD Tools, Wear, 259, 1225, 10.1016/j.wear.2005.02.094 Yanming, 2000, Tool Wear and its Mechanism for Cutting SiC Particle-reinforced Aluminium Matrix Composites, Journal of Materials Processing Technology, 100, 194, 10.1016/S0924-0136(99)00405-7 Muthukrishnan, 2008, Machinability Issues in Turning of Al–SiC (10p) Metal Matrix Composites, International Journal of Advanced Manufacturing Technology, 39, 211, 10.1007/s00170-007-1220-8 Pramanik, 2008, Machining of Metal Matrix Composites: Effect of Ceramic Particles on Residual Stress, Surface Roughness and Chip Formation, International Journal of Machine Tools and Manufacture, 48, 1613, 10.1016/j.ijmachtools.2008.07.008 Ozben, 2008, Investigation of Mechanical and Machinability Properties of SiC Particle Reinforced Al-MMC, Journal of Materials Processing Technology, 198, 220, 10.1016/j.jmatprotec.2007.06.082 Mahamani, 2011, Machinability Study of Al–5Cu–TiB2 In Situ Metal Matrix Composites Fabricated by Flux-Assisted Synthesis, Journal of Minerals and Materials Characterization and Engineering, 10, 1243, 10.4236/jmmce.2011.1013097 Anandakrishnan, 2011, Investigations of Flank Wear, Cutting Force, and Surface Roughness in the Machining of Al-6061–TiB2 In Situ Metal Matrix Composites Produced by Flux-Assisted Synthesis, International Journal of Advanced Manufacturing Technology, 55, 65, 10.1007/s00170-010-3042-3 Rai, 2006, A Study on the Machinability Behaviour of Al–TiC Composite Prepared by In Situ Technique, Materials Science and Engineering A, 428, 34, 10.1016/j.msea.2005.11.040 Kumar, 2014, Effect of Machining Parameters on Cutting Force and Surface Roughness of In Situ Al–4.5%Cu/TiC Metal Matrix Composites, Measurement, 48, 325, 10.1016/j.measurement.2013.11.026 Kumar, 2013, Modeling the Abrasive Wear Characteristics of In-Situ Synthesized Al–4.5%Cu/TiC Composites, Wear, 306, 170, 10.1016/j.wear.2013.08.013 Tosun, 2004, Composites Science and Technology, 64, 299, 10.1016/S0266-3538(03)00290-2 Sandvik-Coromant Co. Inc., 1997 Manna, 2003, Journal of Materials Processing Technology, 140, 711, 10.1016/S0924-0136(03)00905-1 Wu, 2004, Materials Characterization, 52, 81, 10.1016/j.matchar.2003.12.005 Wang, 2004, Materials Science and Engineering A, 364, 339, 10.1016/j.msea.2003.08.049 Karantzalis, 1997, Materials Science and Engineering A, 237, 200, 10.1016/S0921-5093(97)00290-6 Kaasta, 1996, Designing a Neural Network for Forecasting Financial and Economic Time Series, Neurocomputing, 10, 215, 10.1016/0925-2312(95)00039-9