Stress concentration factors of N-joints of concrete-filled tubes subjected to axial loads

Ahmadi, H. and Lotfollahi-Yaghin, M. A. (2012). “Geometrically parametric study of central brace SCFs in offshore threeplanar tubular KT-joints.” Journal of Constructional Steel Research. 71, pp. 149–161.

CIDECT (2000). Design guide for circular and rectangular hollow section welded joints under fatigue loading, Construction With Hollow Steel Sections. Serial No. 8. Verlag TÜV Rheinland, Cologne, Germany.

Efthymiou, M. (1988). “Development of SCF formulae and generalized functions for use in fatigue analysis.” Proc. Offshore Tubular Joints’88, Recent Developments in Tubular Joints Technology, Surrey, UK. pp. 1–33.

Gu, M., Tong, L. W., Zhao, X. L., and Lin, X. G. (2008). “Stress intensity factors of surface cracks in welded Tjoints between CHS brace and concrete-filled chord.” Proc. of 12th International Symposium on Tubular Structures, pp. 359–66.

IIW-1430-00 (2000). Fatigue analysis of welded componentsdesigner’s guide to the structural hot-spot stress approach, Boca Raton: CRC; Cambridge: Woodhead Publishing.

IIW-XV-E (1999). Recommended fatigue design procedure for welded hollow section joints. IIW Docs, XV-1035-99/XIII-1804-99, International Institute of Welding, France.

Jaurrieta, M. A., Alonso, A., and Chica, J. A. (2003). “Welded circular hollow section(CHS) joints in bridges.” Proc. 10th International Symposium in Tubular Structures, pp. 18–20.

Kim, I. K., Chung, C. H., and Kim, Y. J. (2010). “Hot spot stress of concrete-filled circular hollow section N-joints subjected to axial loads.” Journal of KSCE, 30(2A), pp. 113–120.

Lewei, T., Wang, K. S., and Weizhou, C. Y. (2007). “Experimental investigation on stress concentration factors of CHS-to-CFCHS T-joints subjected to in-plane bending.” Proc. Fifth Intl. Conf. on Advances In Steel Structures, pp. 974–978.

Mashiri, F. R. and Zhao, X. L. (2010). “Square hollow section (SHS) T-joints with concrete filled chords subjected to in-plane fatigue loading in the brace.” Thinwalled Structures, 48(2), pp.150–158.

Nazari, A. and Guan, Z. (2007). “Parametric study of hot spot stresses around tubular joints with doubler plates.” Practices Periodical on Structural and Construction, ASCE, 12, pp. 38–47.

Sakai, Y., Hosaka, T., Isoe, A., Ichikawa, A., and Mitsuki, K. (2004). “Experiments on concrete filled and reinforced tubular K-joints of truss girder.” Journal of Constructional Steel Research, 60(3), pp. 683–699.

Shen, W. and Choo, Y. S. (2012). “Stress intensity factor for a tubular T-joint with grouted chord.” Engineering Structures, 35(2), pp. 37–47.

Shim, C. S. and Kim, D. W. (2010). “Structural performance of composite joints using bent studs.” International Journal of Steel Structures, 10(1), pp. 1–13.

Shimizu, M., Tatsumi, F., Ishikawa, T., Hattori, A., and Kawano, H. (2013). “Experimental study on ultimate strength of concrete filled double tubular steel with shear connector.” International Journal of Steel Structures. 13(1), pp. 49–54.

SIMULIA (2007). ABAQUS Version 6.7-1 Documentation. Dassault Systemes.

Tong, L. W., Sun, C. Q., Chen, Y. Y., Zhao, X. L., Shen, B., and Liu, C. B. (2008). “Experimental comparison in hot spot stress between CFCHS and CHS K-joints with gap.” Proc. of 12th International Symposium on Tubular Structures, Shanghai, China, pp. 389–395.

OTH 354 (2000). Stress concentration factors for simple tubular Joints, UK Health and Safety Executive.

OTH 92 368 (1993). Fatigue life enhancement of tubular joints by grout injection, UK Health and Safety Executive.

Yin, Y., Han, Q. H., Bai, L. J., Yang, H. D., and Wang, S. P. (2009). “Experimental study on hysteretic behaviour of tubular N-joints.” Journal of Constructional Steel Research, 65(2), pp. 326–334.

Zhao, X. L. and Tong, L. W. (2011). “New development in steel tubular joints.” Advances in Structural Engineering, 14(4), pp. 699–715.

Zhou, S. and Chen, S. (2003). “Rapid development of CSFT arch bridges in China.” Proc. International Conference on Advances in Structures: Steel, Concrete, Composite and Aluminum, Sydney, Australia, pp. 915–920.