Strength characterization of concrete using industrial waste as cement replacing materials for rigid pavement
Tóm tắt
The excessive use of cement in the construction industry has caused many undesirable consequences. Replacement of cement with industrial by-products like fly ash (FA), ground granulated blast furnace slag (GGBFS), silica fume (SF), metakaolin, rice husk ash, etc., as the mineral admixtures offers several advantages in this modern era of sustainability in construction practice. This paper presents the experimental investigations for assessing the strength properties of the concrete made using the pozzolanic waste materials, i.e. supplementary cementitious materials (SCMs) such as FA, GGBFS and SF as the cement replacing materials. Eight trial mixes were prepared using these materials with varying amount of ordinary Portland cement. These SCMs were kept in equal proportions in all the eight trial mixes. Moreover, superplasticizer was also used for bringing improvement in the workability. The compressive strengths corresponding to the curing period of 7, 28, 40 and 90 days along with the flexural and indirect tensile strengths corresponding to 7, 28 and 40 days curing were evaluated. The study concludes that industrial waste materials can be used as partial replacement of cement and can render sustainable concrete for use in the rigid pavement construction.
Tài liệu tham khảo
Malhotra VM (1999) Making concrete ‘Greener’ with fly ash. Concrete Int 21(5):61–66
Obla KH, Russell LH (2003) Properties of concrete containing ultra-fine fly ash. ACI Mat J 100(5):426–433
Alam J, Akhtar MN (2011) Fly ash utilization in different sectors in Indian scenario. Int J Emerg Trend Eng Develop 1(1):1–14
Silva P, Brito J (2013) Electrical resistivity and capillarity of Self compacting concrete with incorporation of fly ash and lime stone filler. Adv Concrete Const 1(1):65–84. https://doi.org/10.12989/acc.2013.1.1.065
Sunil BM, Manjunatha LS, Ravi L, Yargal SC (2015) Potential use of mine tailings and fly ash in concrete. Adv Concrete Cons 3(1):55–69. https://doi.org/10.12989/acc.2015.3.1.055
Paliwal G, Maru S (2017) Effect of fly ash and plastic waste on mechanical and durability properties of concrete. Adv. In Concrete Const 5(6):575–586. https://doi.org/10.12989/acc.2017.5.6.575
Jena T, Panda KC (2018) Mechanical and durability properties of marine concrete using fly ash and silpozz. Adv Concrete Const 6(1):47–68. https://doi.org/10.12989/acc.2018.6.1.047
Saha AK, Sarker PK (2019) Durability characteristics of concrete using ferronickel slag fine aggregate and fly ash. Mag Concrete Res 70(17):865–874. https://doi.org/10.1680/jmacr.17.00537
Osborne GJ (1999) Durability of Portland blast furnace slag cement concrete. Cem Concr Compos 21(1):11–21
Babu G, Kumar R (2000) Efficiency of GGBS in concrete. Cem Concrete Res 30(7):1031–1136
Tamilarasan VS, Perumal P (2005) Workability studies on concrete with GGBFS as a replacement material for cement with without superplasticizers. Int J Adv Res Eng Tech 3(2):11–21
Garner LJ, Susan A (2015) Characterization of magnesium potassium phosphates cements blended with fly ash and ground granulated blast furnace slag. Cem Concrete Res 74:78–87
Chore HS, Joshi MP (2015) Strength evaluation of concrete with fly ash and GGBFS as cement replacing materials. Adv Conc Const 3(3):223–236. https://doi.org/10.12989/acc.2015.3.3.223
Wild Sabir BB, Khatib JM (1995) Factors influencing strength development of concrete containing silica fume. Cem Concrete Res 25(7):1567–1580. https://doi.org/10.1016/0008-8846(95)00150-B
Bhanja S, Sengupta B (2003) Optimum silica fume content and its mode of action on concrete. Int Concrete Res Inf Portal 100(5):407–412
Nicknam A, Rasa E, Ketabchi (2004) Optimum content of silica fume in cement paste portion of concrete. American Concrete Institute (ACI) Student Conference, San-Francisco, USA
Panjehpour M, Ali A, Demirboga R (2011) A Review for characterization of silica fume and its effects on concrete properties. Int J Sustain Const Eng Tech 2(2):1–7
Saje D, Saje F (2011) Compressive strength of concrete containing Silica fume. J Mech Behav Mater 19(6):355–364
Marikunte SS, Nacer S (2012) Interaction of silica fume and water content on strength and permeability of concrete. In: Transportation Research Board (TRB) annual meeting
Ajileye (2012) Investigation on micro-silica (Silica Fume) as partial cement replacement in concrete. Glob J Res Eng Civil Struct Eng 12(1):Version 1.0
Ramkumar VR, Murali G, Partheeban A (2012) Utilization of silica fume to enhance tensile strength of concrete. Int J Emerg Trends Civil Eng Dev 4(2):607–609
Mane KM, Kulkarni DK, Prakash KB (2019) Properties and microstructure of concrete using pozzolanic materials and manufactured sand as partial replacement of fine aggregate. SN Appl Sci 1:1025. https://doi.org/10.1007/s42452-019-1059-2
Ozyildirim C, Halstead WJ (1994) Improved concrete quality with combination of fly ash and silica fume. ACI Mater J 91(6):587–594
Lam L, Wong YL, Poon CS (1998) Effects of fly ash and silica fume on compressive and fracture behavior of concrete. Cem Concrete Res 28(2):271–283. https://doi.org/10.1016/S0008-8846(97)00269-X
Nochaiya T, Chaipanich A (2010) Utilization of fly ash with silica fume and properties of Portland cement-fly ash-silica fume concrete. Int J Enhanced Res Sci Tech Eng 89(3):768–774. https://doi.org/10.1016/j.fuel.2009.10.003
Laldji S, Tagnit-Hamou A (2006) Properties of ternary and quaternary concrete incorporating new alternative cementitious material. ACI Mater J 103(2):83–89
Ali Sadrmomtazi BT, Reza KK (2019) Effect of fly ash and silica fume on transition zone, pore structure and permeability of concrete. Mag Concrete Res 70(10):519–532. https://doi.org/10.1680/jmacr.16.00537
Ibrahim A, Al- Jumaily S, Naji N, Kareem Q (2015) An overview on the influence of Pozzolanic materials on properties of concrete. Int J Enhanced Res Sci Tech Eng 4(3):81–92
Gesoglu M, Guneyisi E, Ozbay E (2009) Properties of self-compacting concrete made with binary, ternary and quaternary cementitious blends of fly ash, blast furnace slag and silica fume. Const Bldg Mat 23(5):1847–1854. https://doi.org/10.1016/j.conbuildmat.2008.09.015
Patel J, Sheth AJ (2014) High performance concrete using quaternary blend. Int J Innov Res Adv Eng 1(5):133–137
Ganjigatti M, Kashinath BR, Prakash KB (2015) Effect of replacement of cement by different pozzolanic materials on heat of hydration and setting time of concrete. Int J Environ Agric Res 1(4):24–29
Rashad AM (2015) Potential use of silica fume coupled with slag in HVFA concrete exposed to elevated temperature. ASCE J Mat Civil Eng 27(11):04015019. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001274
Kim J-E, park W-S, Young-Il J, Kim S-W, Kim S-W, Nam Y-H, Kim D-G, Rokugo K (2016) Mechanical properties of energy efficient concretes made with binary, ternary and quaternary cementitious blends of fly ash, blast furnace slag and silica fume. Int J Concrete Struct Mater 10:97–108
Praveen Kumar VV, Prasad RD (2019) Study on strength and durability characteristics of lime sludge based blended cement concrete. J Bldg Pathol Rehabilit. https://doi.org/10.1007/s41024-018-0041-5
IS: 12269 (1987) Specification for 53 grade ordinary Portland cement (with Amendment No.3). Bureau of Indian Standards (BIS), New Delhi (India) (Reaffirmed 2013)
IS: 3812 (1981) Specifications for pulverized fuel ash. Bureau of Indian Standards (BIS), New Delhi (India) (Reaffirmed 2013)
IS: 12089 (1987) Specification for granulated slag for manufacture of Portland slag cement. Bureau of Indian Standards (BIS), New Delhi (India)
IS 15388 (2003): Specifications for silica fume. Bureau of Indian Standards, New Delhi (Reaffirmed 2017).
IS: 9013 (1999) Specification for admixture for concrete. Bureau of Indian Standards (BIS), New Delhi (India)
IS: 516 (1959) Methods of tests for strength of concrete. Bureau of Indian Standards (BIS), New Delhi (India) (Reaffirmed 2004)
IS: 5816 (1999) Splitting tensile strength of concrete- Method of test. Bureau of Indian Standards (BIS), New Delhi (India) (Reaffirmed 2004)
IS 10262 (1982) Recommended guidelines for concrete mix design. Bureau of Indian Standards (BIS), New Delhi (India) (Reaffirmed in 1999)
IRC: 58 (2015) Guidelines for the design of plain jointed rigid pavements for highways (Fourth revision). Indian Roads Congress, New Delhi
IRC: 44 (2008) Guidelines for cement concrete mix design for pavements (Second revision). Indian Roads Congress, New Delhi
IS: 456 (2000) Plain and reinforced concrete code of practice (Fourth revision). Bureau of Indian Standards (BIS), New Delhi