Strength and substructure of Al–4.7Mg–0.32Mn–0.21Sc–0.09Zr alloy sheets
Tóm tắt
Laws of the formation of substructure and of changes in the hardness and in the mechanical properties have been established for sheets of 1545K alloy obtained by tension according to different technologies at various accumulated strains. With an increase in cold deformation (e
cold) from 0 to 2.64, the yield stress of cold-worked sheets increases from 355 to 466 МPа and the relative elongation decreases insignificantly from 4 to 3.5%. The maximum strength with σ0.2 = 410 МPа, σu = 460 МPа, and δ = 6.5% is provided by annealing at 150°C for 1 h of the sheets obtained via the technology with the maximum fraction of cold deformation (e
cold = 2.64). After annealing at 300°C for 30 min, a twofold increase in the plasticity is observed without a significant reduction in the strength characteristics a follows: σ0.2 = 385 МPа, σu = 436 МPа and δ = 13%. It has been shown that the level of mechanical properties is determined by the substructure that is formed inside deformed grains during annealing.
Tài liệu tham khảo
Yu. A. Filatov, G. G. Baidin, R. I. Dobrozhinskaya, E. A. Khamnagdaeva, and B. V. Ovsyannikov, “A new 1545K Al–Mg–Sc system-based heat-treatable weldable cryogenic alloy,” Tekhnol. Legk. Splavov, No. 1, 32–36 (2014).
R. Z. Valiev, A. V. Korznikov, and R. R. Mulyukov, “Structure and properties of ultrafine-grained materials produced by severe plastic deformation,” Mater. Sci. Eng., A 168, 141–148 (1993).
Investigations and Applications of Severe Plastic Deformation, NATO Science Series. Series 3, Vol. 80, Ed. by T. C. Lowe and R. Z. Valiev (Kluwer, Dortrecht, 2000), p. 394.
I. Sabirov, M. Yu. Murashkin, and R. Z. Valiev, “Nanostructured aluminum alloys produced by severe plastic deformation: New horizons in development,” Mater. Sci. Eng., A 560, 1–24 (2013).
R. Z. Valiev and T. G. Langdon, “Principles of equalchannel angular pressing as a processing tool for grain refinement,” Prog. Mater. Sci. 51, 881–981 (2006).
A. P. Zhilyaev and T. G. Langdon, “Using high-pressure torsion for metal processing: Fundamentals and applications,” Prog. Mater. Sci. 53, 893–979 (2008).
Y. Saito, H. Utsunomiya, N. Tsuji, and T. Sakai, “Novel ultra-high straining process for bulk materials— Development of the accumulative roll-bonding (ARB) process,” Acta Mater. 47, 579–583 (1999).
V. S. Zolotorevskiy, R. I. Dobrojinskaja, V. V. Cheverikin, E. A. Khamnagdaeva, A. V. Pozdniakov, V. S. Levchenko, and E. S. Besogonova, “Evolution of the structure and mechanical properties of sheets of the of Al–4.7Mg–0.32Mn–0.21Sc–0.09Zr alloy due to deformation accumulated upon rolling,” Phys. Met. Metallogr. 117, 1207–1214 (2016).
Y. J. Chen, Y. C. Chai, H. J. Roven, S. S. Gireesh, Y. D. Yu, and J. Hjelen, “Microstructure and mechanical properties of Al–xMg alloys processed by room temperature ECAP,” Mater. Sci. Eng., A 545, 139–147 (2012).
A. Vinogradov, A. Washikita, K. Kitagawa, and V. I. Kopylov, “Fatigue life of fine-grain Al–Mg–Sc alloys produced by equal-channel angular pressing,” Mater. Sci. Eng., A 349, 318–326 (2003).
H. J. Roven, H. Nesboe, J. C. Werenskiold, and T. Seibert, “Mechanical properties of aluminum alloys processed by SPD: Comparison of different alloy systems and possible product areas,” Mater. Sci. Eng., A 410–411, 426–429 (2005).
E. V. Avtokratova, R. O. Kaibyshev, and O. Sh. Sitdikov, “Fatigue of a fine-grained high-strength Al–6Mg–Sc alloy produced by equal-channel angular pressing,” Phys. Met. Metallogr. 105, 500–508 (2008).
O. Sh. Sitdikov, E. V. Avtokratova, and R. I. Babicheva, “Effect of temperature on the formation of a microstructure upon equal channel angular pressing of the Al–Mg–Sc 1570 alloy,” Phys. Met. Metallogr. 110, 153–161 (2010).
E. V. Avtokratova, O. Sh. Sitdikov, R. O. Kaibyshev, and Y. Watanabe, “Behavior of a submicrocrystalline aluminum alloy 1570 under conditions of cyclic loading,” Phys. Met. Metallogr. 107, 291–297 (2009).
V. I. Trefilov, Yu. V. Mil’man, and S. A. Firstov, Physical Foundations of Strength of Refractory Metals (Naukova Dumka, Kiev, 1975) [in Russian].
G. Landford and M. Cohen, “Microstructural analysis by high-voltage electron diffraction of severely drawn iron wires,” Metall. Trans. A 6, 901–910 (1975).
V. V. Rybin, Large Plastic Deformations and Fracture of Metals (Metallurgiya, Moscow, 1986) [in Russian].
Q. Liu, Jensen D. Juul, and N. Hansen, “Effect of grain orientation on deformation structure in cold-rolled polycrystalline aluminum,” Acta Mater. 46, 5819–5838 (1998).
N. Hansen, X. Huang, R. Ueji, and N. Tsuji, “Structure and strength after large strain deformation,” Mater. Sci. Eng., A 387–389, 191–194 (2004).
P. J. Hurley and F. J. Humphreys, “The application of EBSD to the study of substructural development in a cold rolled single-phase aluminum alloy,” Acta Mater. 51, 1087–1102 (2003).
F. J. Humphreys and P. S. Bate, “The microstructures of polycrystalline Al–0.1Mg after hot plane strain compression,” Acta Mater. 55, 5630–5645 (2007).