Strain analysis in machining using metallographic methods

Komanduri, 1981, On the mechanics of chip segmentation in machining, J. Eng. Ind., 103, 33, 10.1115/1.3184458 Usui, 1964, The theory of plasticity applied to machining with cut-away tools, J. Eng. Ind., 86, 95, 10.1115/1.3670497 Banerjee, 1974, Limit of continuity in some single-phase materials during machining and its correlation with torsion testing, Inter. J. Prod. Res., 12, 117, 10.1080/00207547408919544 van Turkovich, 1970, Shear stress in metal cutting, J. Eng. Ind., 92, 151, 10.1115/1.3427700 Merchant, 1945, Mechanics of metal cutting process. I. orthogonal cutting and a type 2 chip, J. Appl. Phys., 16, 267, 10.1063/1.1707586 Merchant, 1945, Mechanics of the metal cutting process. II. Plasticity conditions in orthogonal cutting, J. Applied Physics, 16, 318, 10.1063/1.1707596 Oxley, 1961, The influence of rate of strain-hardening in machining, 175, 881 Lee, 1954, A plastic flow problem arising in the theory of discontinuous machining, Trans. ASME, 76, 189 Ueda, 1982, An analysis of saw-toothed chip formation, Annals of the CIRP, 31, 81, 10.1016/S0007-8506(07)63273-9 Sullivan, 1978, Metallurgical appraisal of instabilities arising in machining, Met. Tech., 5, 181, 10.1179/mt.1978.5.1.181 von Turkovich, 1982, Machining of titanium and its alloys, 257 Recht, 1964, Catastrophic thermoplastic shear, J. Appl. Mech., 31, 189, 10.1115/1.3629585 Komanduri, 1982, Titanium: A model material for analysis of the high-speed machining process, 241 Komanduri, 1980, New observations on the mechanism of chip formation when machining titanium alloys, Wear, 69, 179, 10.1016/0043-1648(81)90242-8 Wright, 1982, Correlation of tool wear mechanisms with new slip line fields for cutting, Wear, 71, 105, 10.1016/0043-1648(82)90142-9 Komanduri, 1972, The Mechanics of Chip Segmentation Wright, 1979, Strain hardening, strain rate and temperature effects in metal cutting, 14.1 Merchant, 1944, Basic mechanics of the metal-cutting process, J. Appl. Mech., 11, A168, 10.1115/1.4009380 Hill, 1950, The Mathematical Theory of Plasticity, 206 Hill, 1950, The Mathematical Theory of Plasticity, 325 Townend, 1947, Direction of maximum crystal elongation during metal cutting, J. Appl. Phys., 18, 489, 10.1063/1.1697682 Hastings, 1980, A machining theory for predicting chip geometry, cutting forces, etc. from work material properties and cutting conditions, 371, 569 Carro Cao, 1970, Considerations sur le système machine-pièce-outil à l'égard de l'optimalisation des usinages par enlèvement de copeau-II. Les conditions technologiques optimales de la coupe de métaux, Annals of the CIRP, 18, 639 Pearce, 1973, Dynamic chip formation and its significance to machining stability, 187, 273 Wright, 1979, Boundary conditions at the chip-tool interface in machining: Comparisons between seizure and sliding friction, Wear, 54, 371, 10.1016/0043-1648(79)90128-5 Schnur, 1984, Determination of strain distributions in machined chips, Metall. Trans., 15A, 1777, 10.1007/BF02666361 Lee, 1984, The nature or chip formation in orthogonal machining, J. Eng. Ind., 106, 9 Roth, 1972, Slip line field analysis for orthogonal machining bored on experimental flow fields, J. Mech. Eng. Sci., 14, 85, 10.1243/JMES_JOUR_1972_014_015_02 Turley, 1982, Microstructural behavior—Its influence on machining, 99 Lee, 1985, The effect of cutting speed on chip formation under orthogonal machining, J. Eng. Ind., 107, 55, 10.1115/1.3185966 Black, 1979, Flow stress model in metal cutting, J. Eng. Ind., 101, 403, 10.1115/1.3439527