Statistical analysis of surface roughness and cutting forces using response surface methodology in hard turning of AISI 52100 bearing steel with CBN tool

Huang, 2006, CBN tool wear in hard turning: a survey on research progresses, Int J Adv Manuf Technol, 35, 443

Lahiff, 2007, PCBN tool wear modes and mechanisms in finish hard turning, Robot Comput Integr Manuf, 23, 638, 10.1016/j.rcim.2007.02.008

Yallese, 2009, Hard machining of hardened bearing steel using cubic boron nitride tool, J Mater Process Technol, 209, 1092, 10.1016/j.jmatprotec.2008.03.014

Sharma, 2008, Estimation of cutting forces and surface roughness for hard turning using neural networks, J Intell Manuf, 19, 473, 10.1007/s10845-008-0097-1

Nakayama, 1988, Machining characteristics of hard materials, Ann CIRP, 37, 89, 10.1016/S0007-8506(07)61592-3

Strafford, 1997, Indirect monitoring of machinability in carbon steels by measurement of cutting forces, J Mater Process Technol, 67, 150, 10.1016/S0924-0136(96)02835-X

Remadna, 2006, Evolution during time of tool wear and cutting force in the case of hard turning with CBN inserts, J Mater Process Technol, 178, 67, 10.1016/j.jmatprotec.2005.03.038

Arsecularatne, 2006, On machining of hardened AISI D2 steel with PCBN tools, J Mater Process Technol, 171, 244, 10.1016/j.jmatprotec.2005.06.079

Huang, 2005, Modeling of cutting forces under hard turning conditions considering tool wear effect, Trans ASME J Manuf Sci Eng, 127, 262, 10.1115/1.1852571

Chen, 2000, Cutting forces and surface finish when machining medium hardness steel using CBN tools, Int J Mach Tools Manuf, 40, 455, 10.1016/S0890-6955(99)00011-5

Özel, 2005, Effects of cutting edge geometry, workpiece hardness, feed rate and cutting speed on surface roughness and forces in finish turning of hardened AISI H13 steel, Int J Adv Manuf Technol, 25, 262, 10.1007/s00170-003-1878-5

Benga, 2003, Turning of hardened 100Cr6 bearing steel with ceramic and PCBN cutting tools, J Mater Process Technol, 143–144, 237, 10.1016/S0924-0136(03)00346-7

Davim, 2007, Machinability evaluation in hard turning of cold work tool steel (D2) with ceramic tools using statistical techniques, Mater Design, 28, 1186, 10.1016/j.matdes.2006.01.011

Thiele, 1999, Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel, J Mater Process Technol, 94, 216, 10.1016/S0924-0136(99)00111-9

Sahin, 2008, Surface roughness model in machining hardened steel with cubic boron nitride cutting tool, Int J Refract Metals Hard Mater, 26, 84, 10.1016/j.ijrmhm.2007.02.005

Singh, 2007, A surface roughness prediction model for hard turning process, Int J Adv Manuf Technol, 32, 1115, 10.1007/s00170-006-0429-2

Sandvik Coromant. Main catalogue 2006. The official website of the Sandvik Coromant: <http://www.coromant.sandvik.com> [accessed 10.04.2007].

Taguchi, 1987, Taguchi methods, orthogonal arrays and linear graphs, tools for quality engineering, Am Supplier Inst, 35