Spatial and geometrical-based characterization of microstructure and microhardness for an electron beam melted Ti–6Al–4V component

Frazier, 2014, Metal additive manufacturing: a review, J. Mater. Eng. Perform., 23, 1917, 10.1007/s11665-014-0958-z Qiu, 2015, In-situ shelling via selective laser melting: modelling and microstructural characterisation, Mater. Des., 87, 845, 10.1016/j.matdes.2015.08.091 Kok, 2015, Fabrication and microstructural characterisation of additive manufactured Ti–6Al–4V parts by electron beam melting, Virtual. Phys. Prototyp., 10, 13, 10.1080/17452759.2015.1008643 Mazzoli, 2009, Direct fabrication through electron beam melting technology of custom cranial implants designed in a PHANToM-based haptic environment, Mater. Des., 30, 3186, 10.1016/j.matdes.2008.11.013 Tammas-Williams, 2015, XCT analysis of the influence of melt strategies on defect population in Ti–6Al–4V components manufactured by selective electron beam melting, Mater. Charact., 102, 47, 10.1016/j.matchar.2015.02.008 Al-Bermani, 2010, The origin of microstructural diversity, texture, and mechanical properties in electron beam melted Ti–6Al–4V, Metall. Mater. Trans. A, 41, 3422, 10.1007/s11661-010-0397-x Murr, 2014, 10.06 — electron beam melting, 135 Tan, 2015, An experimental and simulation study on build thickness dependent microstructure for electron beam melted Ti–6Al–4V, J. Alloys Compd., 646, 303, 10.1016/j.jallcom.2015.05.178 Tan, 2015, Graded microstructure and mechanical properties of additive manufactured Ti–6Al–4V via electron beam melting, Acta Mater., 97, 1, 10.1016/j.actamat.2015.06.036 Wang, 2015, Effect of building height on microstructure and mechanical properties of big-sized Ti–6Al–4V Plate fabricated by electron beam melting, MATEC Web Conf., 30, 02001, 10.1051/matecconf/20153002001 Murr, 2009, Microstructures and mechanical properties of electron beam-rapid manufactured Ti–6Al–4V biomedical prototypes compared to wrought Ti–6Al–4V, Mater. Charact., 60, 96, 10.1016/j.matchar.2008.07.006 Facchini, 2009, Microstructure and mechanical properties of Ti–6Al–4V produced by electron beam melting of pre-alloyed powders, Rapid Prototyping J., 15, 171, 10.1108/13552540910960262 Ikeo, 2015, Novel powder/solid composites possessing low Young's modulus and tunable energy absorption capacity, fabricated by electron beam melting, for biomedical applications, J. Alloys Compd., 639, 336, 10.1016/j.jallcom.2015.03.141 Ikeo, 2014, Control of mechanical properties of three-dimensional Ti–6Al–4V products fabricated by electron beam melting with unidirectional elongated pores, Metall. Mater. Trans. A, 45, 4293, 10.1007/s11661-014-2396-9 Gong, 2015, Influence of defects on mechanical properties of Ti–6Al–4V components produced by selective laser melting and electron beam melting, Mater. Des., 86, 545, 10.1016/j.matdes.2015.07.147 Sun, 2015, Phase and grain size inhomogeneity and their influences on creep behavior of Co–Cr–Mo alloy additive manufactured by electron beam melting, Acta Mater., 86, 305, 10.1016/j.actamat.2014.11.012 Wang, 2016, 5 Reports Reports Reports Reports Malcolm, 2013 Carroll, 2015, Anisotropic tensile behavior of Ti–6Al–4V components fabricated with directed energy deposition additive manufacturing, Acta Mater., 87, 309, 10.1016/j.actamat.2014.12.054 Mok, 2008, Deposition of Ti–6Al–4V using a high power diode laser and wire, part I: investigation on the process characteristics, Surf. Coat. Technol., 202, 3933, 10.1016/j.surfcoat.2008.02.008 Wang, 2015, Microstructure and mechanical properties of Ti–Zr–Cr biomedical alloys, Mater. Sci. Eng., C, 51, 148, 10.1016/j.msec.2015.02.028 Pan, 2013, β-Phase instability in binary Ti-xNb biomaterial single crystals, Mater. Trans., 54, 156, 10.2320/matertrans.MC201202 Lu, 2013, Correlation between tensile strength and hardness of electron beam welded TC4-DT joints, J. Mater. Eng. Perform., 22, 1694, 10.1007/s11665-012-0469-8 ASTM F1472-14, 2014