Shear Bond Strength of Four Resin Cements Used to Lute Ceramic Core Material to Human Dentin

Journal of Prosthodontics - Tập 17 Số 8 - Trang 634-640 - 2008
Subutayhan Altintas1, Ayçe Ünverdi Eldeniz2, Aslıhan Üşümez3
1Assistant Professor, Department of Prosthodontics, School of Dentistry, Karadeniz Technical University, Trabzon, Turkey
2Assistant Professor, Department of Endodontics, School of Dentistry, Selcuk University, Konya, Turkey
3Associate Professor, Department of Prosthodontics, School of Dentistry, Gaziantep University, Gaziantep, Turkey

Tóm tắt

Abstract Purpose: This study evaluated the effect of four resin cements on the shear bond strength of a ceramic core material to dentin. Materials and Methods: One hundred twenty molar teeth were embedded in a self‐curing acrylic resin. The occlusal third of the crowns were sectioned under water cooling. All specimens were randomly divided into four groups of 30 teeth each according to the resin cement used. One hundred twenty cylindrical‐shaped, 2.7‐mm wide, 3‐mm high ceramic core materials were heat‐pressed. The core cylinders were then luted with one of the four resin systems to dentin (Super‐Bond C&B, Chemiace II, Variolink II, and Panavia F). Half of the specimens (n = 15) were tested after 24 hours; the other half (n = 15) were stored in distilled water at 37°C for 1 day and then thermocycled 1000 times between 5°C and 55°C prior to testing. Shear bond strength of each specimen was measured using a universal testing machine at a crosshead speed of 1 mm/min. The bond strength values were calculated in MPa, and the results were statistically analyzed using a two‐way analysis of variance (ANOVA) and Tukey HSD tests. Results: The shear bond strength varied significantly depending on the resin cement used (p < 0.05). The differences in the bond strengths after thermocycling were not remarkable as compared with the corresponding prethermal cycling groups (p > 0.05). Significant interactions were present between resin cement and thermocycling (p < 0.05). After 24 hours, the specimens luted with Variolink II (5.3 ± 2.2 MPa) showed the highest shear bond strength, whereas the specimens luted with Chemiace II (1.6 ± 0.4 MPa) showed the lowest. After thermocycling, the bond strength values of specimens luted with Chemiace II (1.1 ± 0.1 MPa) and Super‐Bond C&B (1.7 ± 0.4 MPa) decreased; however, this was not statistically significant (p > 0.05). The increase in the shear bond strength values in the Panavia F (4.5 ± 0.7 MPa) and Variolink II (5.5 ± 2.1 MPa) groups after thermocycling was also not statistically significant (p > 0.05). Conclusion: Variolink II and Panavia F systems showed higher shear bond strength values than Chemiace II and Super‐Bond C&B. They can be recommended for luting ceramic cores to dentin surfaces.

Từ khóa


Tài liệu tham khảo

10.1111/j.1365-2842.1985.tb01299.x

Robbins JW, 1993, Fracture resistance of endodontically treated cuspids, Am J Dent, 6, 159

Libman WJ, 1995, Load fatigue of teeth restored with cast posts and cores and complete crowns, Int J Prosthodont, 8, 155

10.1016/0022-3913(90)90070-S

Shillingburg HT, 1997, Fundamentals of Fixed Prosthodontics, 181

10.1016/0022-3913(89)90099-1

10.1016/0300-5712(93)90108-3

10.1111/j.1365-2842.1987.tb00687.x

10.1111/j.1365-2842.1993.tb01645.x

Linde LA, 1984, The use of composites as core material in root‐filled teeth. II. Clinical investigation, Swed Dent J, 8, 209

Kern M, 1998, Preliminary clinical experience with zirconia posts, Dtsch Zahnärztl Z, 53, 266

10.1016/S0022-3913(97)70080-5

Mannocci F, 1999, Intermittent loading of teeth restored using quartz fiber, carbon‐quartz fiber, and zirconium dioxide ceramic root canal posts, J Adhes Dent, 1, 153

Butz F, 2001, Survival rate and fracture strength of endodontically treated maxillary incisors with moderate defects restored with different post and core systems. An in vitro study, Int J Prosthodont, 14, 58

10.1016/S0300-5712(01)00038-0

10.1111/j.1600-9657.1985.tb00571.x

10.1016/S0022-3913(98)70062-9

Sorensen JA, 1998, Rationale and clinical technique for esthetic restoration of endodontically treated teeth with the Cosmopost and IPS Empress post system, Quintessence Dental Technol, 12, 81

Jacobsen PH, 1992, Luting agents for ceramic and polymeric inlays and onlays, Int Dent J, 42, 145

10.1016/S0022-3913(99)70270-2

10.1046/j.1365-2842.2002.00821.x

10.1016/S0109-5641(00)00067-1

10.1016/S0300-5712(00)00058-0

10.1016/S0109-5641(01)00016-1

10.1067/mpr.2002.128034

10.1016/j.dental.2006.01.012

10.1016/j.dental.2005.12.002

10.1016/S0109-5641(03)00052-6

Dong JK, 1992, Heat‐pressed ceramics: technology and strength, Int J Prosthodont, 5, 9

10.1016/S0022-3913(00)80009-8

O'Brien WJ, 2002, Dental Materials and Their Selection

10.1016/j.prosdent.2004.06.027

10.1016/0109-5641(95)80046-8

10.1067/mpr.2002.129063

10.1177/00220345010800070301

10.1177/10454411970080030501

Mondragon E, 2001, Shear strength of dentin and dentin bonded composites, J Adhes Dent, 3, 227

10.1016/S0022-3913(97)70025-8

Thông tin
Thông tin xuất bản

Journal of Prosthodontics

Tập 17 Số 8

634-640

Thông tin tác giả