Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development

Casavola, 2009, Preliminary investigation on distribution of residual stress generated by the selective laser melting process, J Strain Anal Eng Des, 44, 93, 10.1243/03093247JSA464

Osakada, 2006, Flexible manufacturing of metallic products by selective laser melting of powder, Int J Mach Tools Manuf, 46, 1188, 10.1016/j.ijmachtools.2006.01.024

Olakanmi, 2011, Densification mechanism and microstructural evolution in selective laser sintering of Al–12Si powders, J Mater Process Technol, 211, 113, 10.1016/j.jmatprotec.2010.09.003

Yan, 2009, Preparation and selective laser sintering of nylon-12 coated metal powders and post processing, J Mater Process Technol, 209, 5785, 10.1016/j.jmatprotec.2009.06.010

Vutova, 2010, Investigation of electron beam melting and refining of titanium and tantalum scrap, J Mater Process Technol, 210, 1089, 10.1016/j.jmatprotec.2010.02.020

Liu, 2010, Properties of test coupons fabricated by selective laser melting, Key Eng Mater, 447–448, 780, 10.4028/www.scientific.net/KEM.447-448.780

Gu, 2009, In-situ TiC particle reinforced Ti–Al matrix composites: powder preparation by mechanical alloying and selective laser melting behavior, Appl Surf Sci, 255, 9230, 10.1016/j.apsusc.2009.07.008

Amato, 2012, Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting, Acta Mater, 60, 2229, 10.1016/j.actamat.2011.12.032

Dadbakhsh, 2012, Effect of Al alloys on selective laser melting behaviour and microstructure of in situ formed particle reinforced composites, J Alloy Compd, 541, 328, 10.1016/j.jallcom.2012.06.097

Gupta, 2001, Precipitation hardening in Al–Mg–Si alloys with and without excess Si, Mater Sci Eng, A316, 11, 10.1016/S0921-5093(01)01247-3

Thijs, 2013, Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder, Acta Mater, 61, 1809, 10.1016/j.actamat.2012.11.052

Kempen, 2012, Mechanical properties of AlSi10Mg produced by selective laser melting, Phys Procedia, 39, 439, 10.1016/j.phpro.2012.10.059

Bacchewar, 2007, Statistical modelling and optimization of surface roughness in the selective laser sintering process, Proc Inst Mech Eng Part B: J Eng Manuf, 221, 35, 10.1243/09544054JEM670

Carter, 2013

Olakanmi, 2013, Selective laser sintering/melting (SLS/SLM) of pure Al, Al–Mg, and Al–Si powders: Effect of processing conditions and powder properties, J Mater Process Technol, 213, 1387, 10.1016/j.jmatprotec.2013.03.009

Louvis, 2011, Selective laser melting of aluminium components, J Mater Process Technol, 211, 275, 10.1016/j.jmatprotec.2010.09.019

Thijs, 2010, A study of the microstructural evolution during selective laser melting of Ti–6Al–4V, Acta Mater, 58, 3303, 10.1016/j.actamat.2010.02.004

Hofmann Group. Hofmann Innovation Group Website – Concept Laser. <http://www.hofmann-innovation.com/en/technologies/direct-cusing-manufacturing.html>. 2012 [accessed 30.05.14].

Rasband W. ImageJ. U.S. National Institutes of Health, Bethesda, Maryland, USA. <http://imagej.nih.gov/ij>; 1997–2014.

British Standards Institution. Aerospace series. Metallic materials. Test methods. Tensile testing at room temperature (BS EN 2002-1:2005); 2006.

British Standards Institution. Aerospace series. Metallic materials. Test methods. Tensile testing at elevated temperature (BS EN 2002-2:2005); 2006.

Gong H, Rafi K, Starr T, Stucker B. The effects of processing parameters on defect regularity in Ti–6Al–4V parts fabricated by selective laser melting and electron beam melting. in: The 24th international SFF symposium: An additive manufacturing conference. The University Of Texas at Austin; 2013.

Brandl, 2012, Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): microstructure, high cycle fatigue, and fracture behavior, Mater Des, 34, 159, 10.1016/j.matdes.2011.07.067

Kaufman, 1999, 264