Review of vibration-assisted machining

Ahn, 1999, Improvement of micromachining accuracy by 2Dimensional vibration cutting, Proc ASPE, 20, 150

Arcona C. Tool force, chip formation and surface finish in diamond turning. PhD dissertation. North Carolina State University; 1996.

Astashev, 1998, Ultrasonic cutting as a nonlinear (vibro-impact) process, Ultrasonics, 36, 89, 10.1016/S0041-624X(97)00101-7

Astashev, 1992, Effect of ultrasonic vibration of a single-point tool on the process of cutting, J Mach Manuf Reliabil, 3, 65

Babitsky, 2004, Autoresonant control of non-linear mode in ultrasonic transducer for machining applications, Ultrasonics, 42, 29, 10.1016/j.ultras.2004.01.004

Babitsky, 2004, Autoresonant control of ultrasonically-assisted cutting, Mechatronics, 14, 91, 10.1016/S0957-4158(03)00014-X

Babitsky, 2004, Ultrasonically-assisted turning of aviation materials: simulations and experimental Study, Ultrasonics, 42, 81, 10.1016/j.ultras.2004.02.001

Brehl, 2006, Microstructure fabrication using elliptical vibration-assisted machining, Proc ASPE, 39, 511

2007, Proc ASPE, 40

Brinksmeier, 1999, Elliptical vibration cutting of steel with diamond tools, Proc ASPE, 20, 163

Brocato BC. Micromachining using elliptical vibration-assisted machining. MS thesis. North Carolina State University; 2005.

Cerniway MA. Elliptical diamond milling: kinematics, force, and tool wear. MS thesis. North Carolina State University; 2001.

Dautzenberg, 1982, The minimum energy principal applied to the cutting process of various workpiece materials and tool rake angles, CIRP Ann, 31, 91, 10.1016/S0007-8506(07)63275-2

Dambon, 2007, Vibration-assisted machining research at Fraunhofer IPT—diamond turning and precision grinding, Proc ASPE, 40, 3

Gan, 2003, Ultraprecision diamond turning of glass with ultrasonic vibration, Int J Adv Manuf Technol, 21, 952, 10.1007/s00170-002-1416-x

Gao, 2002, Research on the influence of the cutting conditions on the surface microstructure of ultra-thin wall parts in ultrasonic vibration cutting, J Mater Process Technol, 129, 66, 10.1016/S0924-0136(02)00577-0

Han, 1998, Ultrasonically assisted and piezoelectric actuators integrated cutting tool, Jpn J Appl Phys, 37, 4616, 10.1143/JJAP.37.4616

Isaev, 1961, Ultrasonic vibration of a metal cutting tool, Vest Mashinos, 41

Japitana, 2005, Highly efficient manufacture of groove with sharp corner on adjoining surfaces by 6-axis control ultrasonic vibration cutting, Precision Eng, 29, 431, 10.1016/j.precisioneng.2004.12.011

Jin, 2001, Development of a practical ultrasonic vibration cutting tool system, J Mater Process Technol, 113, 342, 10.1016/S0924-0136(01)00649-5

Kazuo, 1988, Machining characteristics of hard metals, CIRP Ann, 37, 89, 10.1016/S0007-8506(07)61592-3

Kim, 1997, Micro surface phenomena of ductile cutting in the ultrasonic vibration cutting of optical plastics, J Mater Process Technol, 68, 89, 10.1016/S0924-0136(96)02546-0

Kim, 1994, A study of the ultrasonic cutting of carbon-fiber reinforced plastics, J Mater Process Technol, 43, 259, 10.1016/0924-0136(94)90025-6

Kim, 1998, Characteristics of chip generation by ultrasonic vibration cutting with extremely low cutting velocity, Int J Adv Manuf Technol, 14, 2, 10.1007/BF01179410

Klocke, 2004, Material removal mechanisms in ultrasonic-assisted diamond turning of brittle materials, Int J Mater Product Technol, 20, 231, 10.1504/IJMPT.2004.004249

Klocke, 2005, Advanced tool-edge geometry for high-precision hard turning, CIRP Ann, 54-1, 47, 10.1016/S0007-8506(07)60046-8

Klocke, 2000, Ultrasonic-assisted diamond turning of glass and steel, Ind Diamond Rev, 229

Kumbabe, 1979

Lee, 2000, A study on micro-grooving characteristics of planar lightwave circuit and glass using ultrasonic vibration cutting, J Mater Process Technol, 130–131, 396

Li, 2006, Ultrasonic-elliptical vibration transducer driven by single actuator and its application in precision cutting, J Mater Process Technol, 180, 91, 10.1016/j.jmatprotec.2006.05.007

Liu, 2002, Research on the characteristics of the cutting force in the vibration cutting of a particle-reinforced metal matrix composite SiCp/Al, J Mater Process Technol, 129, 196, 10.1016/S0924-0136(02)00649-0

Liu, 2004, Study of ductile mode cutting in grooving of tungsten carbide with and without ultrasonic vibration assistance, Int J Adv Manuf Technol, 24, 389, 10.1007/s00170-003-1647-5

Ma, 2005, Suppression of burrs in turning with ultrasonic elliptical vibration cutting, Int J Mach Tools Manuf, 45-11, 1295, 10.1016/j.ijmachtools.2005.01.011

Ma, 2004, Study of machining accuracy in ultrasonic elliptical vibration cutting, Int J Mach Tools Manuf, 44, 1305, 10.1016/j.ijmachtools.2004.04.014

Ma, 2004, Study on the thrust cutting force in elliptical vibration cutting, Mater Sci Forum, 471–472, 396, 10.4028/www.scientific.net/MSF.471-472.396

Ma, 2005, Drilling assisted by ultrasonic elliptical vibration, Key Eng Mater, 291–292, 443, 10.4028/www.scientific.net/KEM.291-292.443

Mitrofanov, 2005, Effect of lubrication and cutting parameters on ultrasonically-assisted turning of inconel 718, J Mater Process Technol, 162–163, 649, 10.1016/j.jmatprotec.2005.02.170

Mitrofanov, 2003, Finite element simulations of ultrasonically assisted turning, Comput Mater Sci, 28, 646, 10.1016/j.commatsci.2003.08.020

Mitrofanov, 2005, Thermomechanical finite element simulations of ultrasonically assisted turning, Comput Mater Sci, 32, 463, 10.1016/j.commatsci.2004.09.019

Mitrofanov, 2004, Finite-element analysis of ultrasonically-assisted turning of inconel 718, J Mater Process Technol, 153–154, 233, 10.1016/j.jmatprotec.2004.04.299

Moriwaki, 1995, Ultrasonic elliptical vibration cutting, CIRP Ann, 44, 31, 10.1016/S0007-8506(07)62269-0

Moriwaki, 1992, Ultraprecision ductile cutting of glass by applying ultrasonic vibration, CIRP Ann, 41

Moriwaki, 1991, Ultraprecision turning of stainless steel by applying ultrasonic vibration, CIRP Ann, 40, 559, 10.1016/S0007-8506(07)62053-8

Negishi N. Elliptical vibration-assisted machining with single crystal diamond tools. MS thesis. North Carolina State University; 2003.

Overcash, 2003, Development of a tunable ultrasonic vibration-assisted diamond turning instrument, Proc ASPE, 30, 503

Paul, 1996, Chemical aspects of tool wear in single-point diamond turning, Precision Eng, 18, 4, 10.1016/0141-6359(95)00019-4

Rubenach, 2003, From process innovation to product innovation—ultrasonic-assisted diamond turning of optical glass, Ind Diamond Rev, 41

Scattergood, 1991, Ductile-regime machining model for diamond turning of brittle materials, Precision Eng, 13, 95, 10.1016/0141-6359(91)90500-I

Shamoto, 1994, Study on elliptical vibration cutting, CIRP Ann, 43, 35, 10.1016/S0007-8506(07)62158-1

Shamoto, 1999, Ultraprecision diamond cutting of hardened steel by applying elliptical vibration cutting, CIRP Ann, 48, 441, 10.1016/S0007-8506(07)63222-3

Shamoto, 2007, Simulation of elliptical vibration cutting process with thin shear plane model, Proc ASPE, 40, 64

Shamoto, 2002, Development of ultrasonic elliptical vibration controller for elliptical vibration cutting, CIRP Ann, 51, 327, 10.1016/S0007-8506(07)61528-5

Shamoto, 2005, Development of 3-DOF ultrasonic vibration tool for elliptical vibration cutting of sculptured surfaces, CIRP Ann, 54, 321, 10.1016/S0007-8506(07)60113-9

Shamato, 2005, Ultraprecision micromachining of hardened die steel by applying elliptical vibration cutting, JSME News, 16, 1

Shamoto, 1999, Elliptical vibration cutting -3rd report, application to three dimensional cutting and investigation of practical effects, J JSPE, 65, 586

Shamoto, 1996, Elliptical vibration cutting -1st report, cutting principle and basic performance, J JSPE, 62, 1127

Shamoto, 1999, Elliptical vibration cutting -2nd report, study on effects of vibration conditions, J JSPE, 65, 411

Shimada, 2004, Thermochemical wear mechanisms in machining of ferrous metals, CIRP Ann, 53, 57, 10.1016/S0007-8506(07)60644-1

Skelton, 1968, Turning with an oscillating tool, Int J Mach Tool Des Res, 8, 239, 10.1016/0020-7357(68)90014-0

Sugawara K. Study on elliptical vibration cutting and its applications. MS thesis. Kobe University; 1999.

Suzuki, 2007, Development of 3-DOF ultrasonic elliptical vibration system for elliptical vibration cutting, Proc ASPE, 40, 15

Suzuki, 2004, Ultraprecision micromachining of brittle materials by applying ultrasonic elliptical vibration cutting, 133

Suzuki, 2003, Ultraprecision micromachining of hardened steel by applying ultrasonic elliptical vibration cutting, IEEE Int Sym Micromechatronics Human Sci, 221

Weber, 1984, Turning of machinable glass ceramics with an ultrasonically vibrated tool, CIRP Ann, 33, 85, 10.1016/S0007-8506(07)61385-7

Xiao, 2002, Analysis of Chatter Suppression in Vibration Cutting, Int J Mach Tools Manuf, 42, 1677, 10.1016/S0890-6955(02)00077-9

Xiao, 2003, The effect of tool nose radius in ultrasonic vibration cutting of hard metal, Int J Mach Tools Manuf, 43, 1375, 10.1016/S0890-6955(03)00129-9

Xu, 1999, Piezoelectric actuator-based active error compensation of precision machining, Meas Sci Technol, 10, 106, 10.1088/0957-0233/10/2/008

Zhong, 2005, Diamond turning of a metal matrix composite with ultrasonic vibrations, Mater Manuf Process, 20, 727, 10.1081/AMP-200055124

Zhou, 2003, Vibration-assisted precision machining of steel with PCD tools, Mater Manuf Process, 18, 825, 10.1081/AMP-120024978

Zhou, 2002, Brittle-ductile transition in the diamond cutting of glasses with the aid of ultrasonic vibration, J Mater Process Technol, 121, 243, 10.1016/S0924-0136(01)01262-6