Nội dung được dịch bởi AI, chỉ mang tính chất tham khảo
Căng thẳng dư trong chuỗi thép có độ bền cao 18CrNiMo7-6 hàn ma sát thẳng
Tóm tắt
Hàn ma sát thẳng là một quá trình hàn trạng thái rắn, bao gồm việc làm nóng nhanh và làm nguội các bộ phận hàn. Căng thẳng dư (RS), như trong mọi quá trình hàn khác, không thể tránh khỏi. Sự hiện diện của RS làm suy yếu hiệu suất và độ tin cậy trong quá trình sử dụng. Chúng ảnh hưởng đến hiện tượng nứt do ăn mòn ứng suất, độ bền mỏi và tốc độ phát triển nứt. Biết được quy mô và tính chất của những căng thẳng này rất quan trọng để cải thiện chất lượng mối hàn. Do đó, bốn giai đoạn chế tạo khác nhau của các liên kết chuỗi hàn ma sát thẳng đã được phân tích trong nghiên cứu này: “đã rèn” (F), “đã hàn” (A), “đã hàn” không có phần rìa (N), và xử lý nhiệt sau hàn (P). Lĩnh vực căng thẳng dư đã được đo bằng phương pháp khoan lỗ (HD). Kết quả từ phương pháp khoan lỗ cho thấy độc lập với vị trí đo và độ đối xứng liên quan đến mối hàn được quan sát trong tất cả các khu vực đánh giá. Gần với đường giữa của mối hàn (WCL), các căng thẳng nén trong trạng thái “đã rèn” chuyển sang trạng thái kéo do quá trình hàn. Tuy nhiên, ở các khu vực xa hơn, các căng thẳng gần như không thay đổi đối với cả A và N. PWHT làm đồng nhất hóa lĩnh vực căng thẳng dư dọc theo toàn bộ khu vực hàn.
Từ khóa
#căng thẳng dư #hàn ma sát thẳng #chuỗi thép #phân tích căng thẳng #xử lý nhiệt sau hànTài liệu tham khảo
Funderburk S (1986) Postweld heat treatments, pergamon press Ltd., Encycl. Mater …, vol. XV, no. 2
McAndrew AR, Colegrove PA, Flipo BCD, Bühr C (2016) 3D modelling of Ti–6Al–4V linear friction welds. Sci Technol Weld Join., vol. XXII. (December) p 1–9
Bhamji I, Preuss M, Threadgill PL, Moat RJ, Addison AC, Peel MJ (2010) Linear friction welding of AISI 316L stainless steel. Mater Sci Eng A 528(2):680–690
Smith M, Levesque J-B, Bichler L, Sediako D, Gholipour J, Wanjara P (2017) Residual stress analysis in linear friction welded in-service Inconel 718 superalloy via neutron diffraction and contour method approaches. Mater Sci Eng A 691(February):168–179
Vairis A (2012) Mathematical modelling of the linear friction welding process. J Eng Sci Technol Rev 5(3):25–31
Li WY, Ma TJ, Yang SQ, Xu QZ, Zhang Y, Li JL, Liao HL (2008) Effect of friction time on flash shape and axial shortening of linear friction welded 45 steel. Mater Lett 62(2):293–296
Bhamji I, Preuss M, Threadgill PL, Addison AC (2011) Solid state joining of metals by linear friction welding: a literature review. Mater Sci Technol 27(1):2–12
Schajer GS (2010) Advances in hole-drilling residual stress measurements. Exp Mech 50(2):159–168
Schajer GS (2009) Hole-drilling residual stress measurements at 75: origins, advances, opportunities, Exp Mech, vol. L
Rendler NJ, Vigness I (1966) Hole-drilling strain-gage method of measuring residual stresses. Exp Mech 6(12):577–586
Rossini NS, Dassisti M, Benyounis KY, Olabi AG (2012) Methods of measuring residual stresses in components. Mater Des 35:572–588
Barile C, Casavola C, Pappalettera G, Pappalettere C (2014) Remarks on residual stress measurement by hole-drilling and electronic speckle pattern interferometry. ScientificWorldJournal 2014:1–7
Lohe D, Vohringer O (2002) Handbook of residual stress and deformation of steel, vol. I
V. P. Group (2010) Measurement of residual stresses by the hole-drilling* strain gage method, Tech Note TN-503 11053:19–33
Stefanescu D, Truman CE, Smith DJ, Whitehead PS (2006) Improvements in residual stress measurement by the incremental centre hole drilling technique. Exp Mech 46(4):417–427
Effertz PS, Fuchs F, Enzinger N (2017) Modelling the flash formation of linear friction welded 30CrNiMo8 high strength steel chains. Int J Adv Manuf Technol 92:2479–2486
Loffelmann J (2012) Systematische Untersuchung der Schweissparameter beim linearen Reibschweissen.pdf, 2nd IIW European-South American School of Welding and Correlated Processes
Nobre JP, Kornmeier M, Dias AM, Scholtes B. Use of the hole-drilling method for measuring residual stresses in highly stressed shot-peened surfaces, vol. XL, p. 289–297
Buchanan DJ, John R (2014) A residual stress redistribution in shot peened samples subject to mechanical loading. Mater Sci Eng A 615:70–78
Xie P, Zhao H, Liu Y, Xie P, Zhao H, Liu Y (2017) Measuring residual stresses in linear friction welded joints composed by dissimilar titanium measuring residual stresses in linear friction welded joints composed by dissimilar titanium, Science and technology of welding and joining vol. XXI, no.5
Turner R, Ward RM, March R, Reed RC (2012) The magnitude and origin of residual stress in Ti-6Al-4V linear friction welds: an investigation by validated numerical modeling. Metall Mater Trans B Process Metall Mater Process Sci 43(1):186–197
Frankel P, Preuss M, Steuwer A, Withers PJ, Bray S (2009) Comparison of residual stresses in Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo linear friction welds. Mater Sci Technol 25(5):640–650