Residual stress influences on structural reliability

James, 2007, Residual stresses and fatigue performance, Eng Fail Anal, 14, 384, 10.1016/j.engfailanal.2006.02.011

Champaigne J. Shot peening overview, www.shotpeener.com/learning/spo.pdf; 2010 [accessed 30.09.10].

Kirkhope, 1999, Weld detail fatigue life improvement techniques. Part 1: review, Marine Struct, 12, 447, 10.1016/S0951-8339(99)00013-1

James, 2010, Shot-peening of turbine blades: residual stresses and their modification by fatigue, Procedia Eng, 2, 441, 10.1016/j.proeng.2010.03.048

Pense A. HPS corrugated web girder fabrication innovations, Final Report Part 4: Literature and experimental study of strain aging in HPS and other bridge steels, Lehigh University, 2004.

Pereloma, 2010, Effect of Cr and Mo on strain ageing behaviour of low carbon steel, Mater Sci Eng, A527, 2538, 10.1016/j.msea.2009.12.040

ASTM A143/A143M-07, Standard practice for safeguarding against embrittlement of hot-dip galvanized structural steel products and procedure for detecting embrittlement, ASTM International, Pennsylvania, USA 2007.

Auzoux, 2010, Effect of pre-strain on creep of three AISI 316 austenitic stainless steels in relation to reheat cracking of weld-affected zones, J Nuc Mater, 400, 127, 10.1016/j.jnucmat.2010.02.021

Dhooge, 1987, Reheat cracking – a review of recent studies, Int J Pres Ves Pip, 27, 239, 10.1016/0308-0161(87)90012-3

Lant, 2001, Review of weld repair procedures for low alloy steels designed to minimise the risk of future cracking, Int J Pres Ves Pip, 78, 813, 10.1016/S0308-0161(01)00094-1

BS EN 1011-2:2001, Welding. Recommendations for welding of metallic materials. Arc welding of ferritic steels, British Standards Institution, London, 2001.

Pargeter, 2010, Welding of hydrogen-charged steel for modification or repair, Weld J, 89, 34

Berman, 1985, The effect of baking and stress on the hydrogen content of cadmium plated high strength steels, Mater Perform, 24, 36

James, 2009, Designing against LMAC in galvanised steel structures, Eng Fail Anal, 16, 1051, 10.1016/j.engfailanal.2008.05.019

Zervoudis J, Anderson G. Galvanised steel cracking literature review, Teck Cominco Ltd., Canada, Report TS-20-303, December, 2003.

European Union Research Fund for Coal and Steel, FAMEGA: failure mechanisms during galvanising, Contract RFSR-CT-2003-0002; 2003-2007.

Feldmann M. Cracking of large steel structures during HDG, Presentation at Intergalva 2006, European General Galvanisers Association, Naples, Italy; 11–16 June 2006.

Ravn-Jensen, 1990, Effect of residual stresses on plastic buckling of cylindrical shell structures, Int J Solids Struct, 26, 993, 10.1016/0020-7683(90)90013-L

Fujikubo, 1999, Elastic local buckling strength of stiffened plate considering plate/stiffener interaction and welding residual stress, Mar Struct, 12, 543, 10.1016/S0951-8339(99)00032-5

Nishino, 1968, Residual stress and torsional buckling strength of H and cruciform columns, Trans Jpn Soc Civ Eng, 160, 75

European Steel Design Education Programme, http://www.esdep.org/members/master/toc.htm, (1993), accessed on 10/10/2010.

Kandil FA, Lord JD, Fry AT, Grant PV. A review of residual stress measurement methods – a guide to technique selection, National Physical Laboratory Materials Centre, Teddington, UK, NPL Report MATC(A)04, 2001

Withers, 2001, Residual stress. Part 1 – Measurement techniques, Mater Sci Technol, 17, 355, 10.1179/026708301101509980

Withers, 2001, Residual stress. Part 2 – Nature and origins, Mater Sci Technol, 17, 366, 10.1179/026708301101510087

Leggatt, 1996, Development and experimental validation of the deep hole method for residual stress measurement, J Strain Anal Eng Des, 31 3, 177, 10.1243/03093247V313177

Prime, 2001, Cross-sectional mapping of residual stresses by measuring the surface contour after a cut, J Eng Mater Technol, 123, 162, 10.1115/1.1345526

Dye, 2001, Intergranular and interphase microstresses, Curr Opin Solid State Mater Sci, 5, 31, 10.1016/S1359-0286(00)00019-X