Research on the dynamic mechanical properties and constitutive model of metal rubber under impact loading
Tóm tắt
The development of lightweight, impact-resistant and high energy dissipation materials is of great significance to reduce the hazards of explosions and impacts. Metal rubber (MR) has the characteristics of low density, high damping performance and high elasticity, which shows great potential in the field of protection. However, there are few studies on the dynamic mechanical response of MR under high-speed impact. A series of experiments were carried out to study the mechanical properties of MR. It is found that the deformation mechanism of the metal wire inside the MR determines the mechanical properties. Under quasi-static conditions, the stress-strain of MR includes an elastic stage, a softening stage and a hardening stage, and the stress-strain under high-speed impact includes an elastic stage, a softening stage and a failure stage. In addition, the smaller the wire diameter, the higher the load-bearing capacity of the MR. The damage characteristics of MR under high-speed impact are divided into expansion failure and compaction failure, which will affect mechanical performance in the failure stage. The calculated energy absorption and ideal energy absorption efficiency show that MR is a material with excellent energy absorption properties. The dynamic elastic modulus and dynamic peak stress of MR have strain rate effect and density effect. A constitutive model based on Sherwood-frost equation was established, which can precisely forecast the dynamic mechanical properties.
Từ khóa
Tài liệu tham khảo
Lazarus, 2020, A review of impact resistant biological and bioinspired materials and structures, Journal of Materials Research and Technology, 9, 15705, 10.1016/j.jmrt.2020.10.062
Zhang, 2020, Tailoring an impact resistant engineered cementitious composite (ECC) by incorporation of crumb rubber, Constr. Build. Mater., 262, 120116, 10.1016/j.conbuildmat.2020.120116
Chen, 2020, Polyurea coating for foamed concrete panel: an efficient way to resist explosion, Defence Technology, 16, 136, 10.1016/j.dt.2019.06.010
Zhang, 2018, Failure analyses of flexible Ultra-High Molecular Weight Polyethylene (UHMWPE) fiber reinforced anti-blast wall under explosion, Compos. Struct., 184, 759, 10.1016/j.compstruct.2017.10.037
Zhou, 2019, Experimental and numerical investigation of high velocity soft impact loading on aircraft materials, Aerosp. Sci. Technol., 90, 44, 10.1016/j.ast.2019.04.015
French, 2010, 244
Rawat, 2020, Structural and mechanical properties of fish scales for the bio-inspired design of flexible body armors: a review, Acta Biomater, 121, 41, 10.1016/j.actbio.2020.12.003
Bds, 2020, Enhanced visco-elastic and rheological behavior of epoxy composites reinforced with polyimide nanofiber, Nano-Structures & Nano-Objects, 21, 10.1016/j.nanoso.2019.100421
Remanan, 2020, Nano to microblend formation in poly(ethylene-co-methyl acrylate)/ poly(vinylidene fluoride) blend and investigation of its anomalies in rheological properties, Nano-Structures & Nano-Objects, 23, 10.1016/j.nanoso.2020.100487
Sobotka, 2014
Patanair, 2020, Confinement effects at nanoscale in natural rubber composites: influence on macroscopic properties, Journal of Applied Polymer Science, 138, 49838, 10.1002/app.49838
Vijayan, 2014, Liquid rubber and silicon carbide nanofiber modified epoxy nanocomposites: Volume shrinkage, cure kinetics and properties, Composites Science & Technology, 102, 65, 10.1016/j.compscitech.2014.07.017
Ponnamma, 2013, Synergistic effect of multi walled carbon nanotubes and reduced graphene oxides in natural rubber for sensing application, Soft Matter, 9, 10343, 10.1039/c3sm51978c
Xue, 2020, Manufacture technology and anisotropic behaviour of elastic-porous metal rubber, International Journal of Lightweight Materials and Manufacture, 3, 88, 10.1016/j.ijlmm.2019.08.005
Zhang, 2013, Compression mechanics of nickel-based superalloy metal rubber, Materials Science & Engineering A, 580, 305, 10.1016/j.msea.2013.05.064
Tan, 2009, Mechanical behaviors of quasi-ordered entangled aluminum alloy wire material, Mater. Sci. Eng. A, 527, 38, 10.1016/j.msea.2009.07.022
Liu, 2009, Impact behavior of entangled steel wire material, Mater. Charact., 60, 900, 10.1016/j.matchar.2009.03.001
Liu, 2009, Structure deformation and failure of sintered steel wire mesh under torsion loading, Mater. Des., 30, 2264, 10.1016/j.matdes.2008.09.007
Tan, 2013, Stretching behaviors of entangled materials with spiral wire structure, Mater. Des., 46, 61, 10.1016/j.matdes.2012.10.003
Buratti, 2010
Courtois, 2012, Mechanical properties of monofilament entangled materials, Adv. Eng. Mater., 14, 1128, 10.1002/adem.201100356
Liu, 2010, Compressive and pseudo-elastic hysteresis behavior of entangled titanium wire materials, Mater. Sci. Eng. A, 527, 3301, 10.1016/j.msea.2010.02.071
He, 2012, Porous titanium materials with entangled wire structure for load-bearing biomedical applications, J. Mech. Behav. Biomed. Mater., 5, 16, 10.1016/j.jmbbm.2011.09.016
Jiang, 2014, Enhancement of the porous titanium with entangled wire structure for load-bearing biomedical applications, Materials & Design (1980–2015), 56, 241, 10.1016/j.matdes.2013.11.019
Zhang, 2013, Compression mechanics of nickel-based superalloy metal rubber, Mater. Sci. Eng. A, 580, 305, 10.1016/j.msea.2013.05.064
Ma, 2015, The mechanics of shape memory alloy metal rubber, Acta Mater., 96, 89, 10.1016/j.actamat.2015.05.031
Chegodaev, 2000, Design of metal rubber components, Press of National Defense Industry, 2, 2
Tuo, 2015, Study on preparation technology and tests of knitted-dapped metal rubber, 10.13433/j.cnki.1003-8728.2015.0331
Yuyan, 2005, A Theoretical model and experimental investigation of a nonlinear constitutive equation for elastic porous metal rubbers, Mech. Compos. Mater., 41, 303, 10.1007/s11029-005-0056-2
Peng, 2005, A micromechanics constitutive model of the metal rubber materials based on the radial and axial combined deformation of the microsprings, Journal of Experimental Mechanics, 20, 455
Bao-Ting, 2004, Theoretical Model of Metal-Rubber, Journal of Aerospace Power, 03, 314
Hong, 2011, Theoretical and experimental investigation on nonlinear characterization of metal rubber, Journal of Physics, 62, 470, 10.7498/aps.62.048101
Jun, 2019, Dynamic mechanical properties and constitutive model of honeycomb materials with random defects under impact loading, Shock and Vibration, 2019, 1, 10.1155/2019/1087919
Yu, 2007, Research into the effect of cell diameter of aluminum foam on its compressive and energy absorption properties, Mater. Sci. Eng. A, 454–455, 542, 10.1016/j.msea.2006.11.091
Miltz, 1981, Evaluation of cushioning properties of plastic foams from compressive measurements, Polymer Engineering & Science, 21, 1010, 10.1002/pen.760211505
Hua, 2018, Research on dynamic accumulation effect and constitutive model of aluminum foams under dynamic impact, Int. J. Metalcast., 13, 146, 10.1007/s40962-018-0245-0