Reducing Stress Concentration Around a Hole in a Thin-Wall Cylinder Subjected to Internal Pressure Using Piezoelectric Patches

ASME Committee on Pressure Vessels (2015) Rules for construction of pressure vessels: Sec VIII, Div 1. American Society of Mechanical Engineers Budynas RG, Nisbett JK (2008) Shigley’s mechanical engineering design. McGraw-Hill, New York Dorigo M, Maniezzo V, Colorni A (1996) Ant system: optimization by a colony of cooperating agents. IEEE Trans Syst Man Cybern Part B Cybern 26:29–41 Fesharaki JJ (2014) Optimum pattern of piezoelectric actuator placement for stress concentration reduction in a plate with a hole using particle swarm optimization algorithm. In: Proceedings of the institution of mechanical engineers, part c: journal of mechanical engineering science, p 0954406214538617 Fesharaki JJ, Golabi SI (2016a) Effect of stiffness ratio of piezoelectric patches and plate on stress concentration reduction in a plate with a hole. Mech Adv Mater Struct 24:1–32 Fesharaki JJ, Golabi SI (2016b) A novel method to specify pattern recognition of actuators for stress reduction based on Particle swarm optimization method. Smart Struct Syst 17:725–742 Fesharaki JJ, Madani SG (2016) Effect of stiffness and thickness ratio of host plate and piezoelectric patches on reduction of the stress concentration factor. Int J Adv Struct Eng 8:229–242 Fesharaki JJ, Madani SG, Golabi S (2018) Best pattern for placement of piezoelectric actuators in classical plate to reduce stress concentration using PSO algorithm. Mech Adv Mater Struct. https://doi.org/10.1080/15376494.2018.1472332 Fridman A (1986) Asymptotic method of investigating the deformation of cylindrical shells with holes. Soviet Appl Mech 22:1181–1186 Golabi SI, Fesharaki JJ (2014) Reducing stress concentration factor around a hole on a plate by piezoelectric patch. Int J Adv Des Manuf Technol 6:59–64 Hsu C-Y, Liang C-C, Shiah S-W, Jen C-Y (2005) A study of stress concentration effect around penetrations on curved shell and failure modes for deep-diving submersible vehicle. Ocean Eng 32:1098–1121 Kamalarajah R, Stoffberg W, Bull JW, Chizari M (2015) Stress analysis of uniform circular cylindrical shells with large circular holes. In: Lecture notes in engineering and computer science: proceedings of the world congress on engineering Kharat A, Kulkarni V (2013) Stress concentration at openings in pressure vessels-a review. Int J Innov Res Sci Eng Technol 2:670–677 Kornecki A (1966) Comments on stresses about a circular hole in a cylindrical shell. AIAA J 4:0765a–0765a Lind N (1968) Stress concentration of holes in pressurized cylindrical shells. AIAA J 6:1397 Lu M-H, Yu J-S, Chen J-J (2014) The effect of analysis model on the stress intensity calculation for the nozzle attached to pressure vessel under internal pressure loading. Int J Press Vessels Pip 117:9–16 Mehrabian AR, Yousefi-Koma A (2011) A novel technique for optimal placement of piezoelectric actuators on smart structures. J Franklin Inst 348:12–23 Mirzagoltabar M (2014) Studying decreased methods of stress concentration around holes and openings in plate and shell structures. Science International, vol. 26, no. 1. Gale Academic Onefile. https://go.galegroup.com/ps/anonymous?id=GALE%7CA376229623&sid=googleScholar&v=2.1&it=r&linkaccess=abs&issn=10135316&p=AONE&sw=w. Accessed 30 Sept 2019 Mukhtar F, Al-Gahtani H (2016) Finite element analysis and development of design charts for cylindrical vessel-nozzle junctures under internal pressure. Arab J Sci Eng 41:4195–4206 Nguyen Q, Tong L (2007) Voltage and evolutionary piezoelectric actuator design optimisation for static shape control of smart plate structures. Mater Des 28:387–399 Przybylski J (2008) Stability of an articulated column with two collocated piezoelectric actuators. Eng Struct 30:3739–3750 Rajaiah K, Kumar RR (1982) Optimum hole shapes in circular cylindrical shells under tension and torsion. Mech Res Commun 9:85–93 Rajaiah K, Kumar RR (1985) Stresses around circular, square and optimized holes in circular cylindrical shells under torsion. Int J Solids Struct 21:177–185 Ramsey J Jr (1975) Stress concentration factors for circular, reinforced penetrations in pressurized cylindrical shells, Ph.D, thesis-Virginia Univ Ryu C-H, Lee Y-S, Choi M-H, Kim Y-W (2004) A study on stress analysis of orthotropic composite cylindrical shells with a circular or an elliptical cutout. J Mech Sci Technol 18:808–813 Sensharma PK, Haftka RT (1996) Limits of stress reduction in a plate with a hole using piezoelectric actuators. J Intell Mater Syst Struct 7:363–371 Sensharma PK, Palantera MJ, Haftka RT (1993) Stress reduction in an isotropic plate with a hole by applied induced strains. J Intell Mater Syst Struct 4:509–518 Shah D, Joshi S, Chan W (1994) Stress concentration reduction in a plate with a hole using piezoceramic layers. Smart Mater Struct 3:302 Uchino K, Debus J-C (2012) Applications of ATILA FEM software to smart materials: case studies in designing devices. Elsevier, Amsterdam Van Dyke P (1965) Stresses about a circular hole in a cylindrical shell. AIAA J 3:1733–1742 Wu N, Wang Q (2011) An experimental study on the repair of a notched beam subjected to dynamic loading with piezoelectric patches. Smart Mater Struct 20:115023 Xue M-D, Du Q-H, Hwang K-C, Xiang Z-H (2010a) An analytical method for cylindrical shells with nozzles due to internal pressure and external loads—part I: theoretical foundation. J Press Vessel Technol 132:031206 Xue M-D, Du Q-H, Hwang K-C, Xiang Z-H (2010b) An analytical method for cylindrical shells with nozzles due to internal pressure and external loads—part II: design method. J Press Vessel Technol 132:031207