Production and mechanical properties of Al2O3 particle-reinforced 2024 aluminium alloy composites
Tóm tắt
Từ khóa
Tài liệu tham khảo
Hanumanth, 1993, Particle incorporation by melt stirring for the production of metal-matrix composites, J. Mater. Sci., 28, 2459, 10.1007/BF01151680
Sahin, 1996, The effect of fibre orientation of the dry sliding wear of borsic-reinforced 2014 aluminium alloy, J. Mater. Sci., 34, 5399, 10.1007/BF01159309
Seo, 1995, The effect of applied pressure on particle-dispersion characteristics and mechanical properties in melt-stirring squeeze-cast SiC/Al composites, J. Mater. Process. Technol., 55, 370, 10.1016/0924-0136(95)02033-0
Purazrang, 1991, Fracture toughness behaviour of a magnesium alloy metal-matrix composite produced by the infiltration technique, Composites, 22, 456, 10.1016/0010-4361(91)90205-U
Mostaghaci, 1989, Processing of ceramic and metal matrix composites
Gibson, 1985, Production and evaluation of squeeze cast graphitic Al–Si alloy, Mater. Sci. Technol., 1, 558, 10.1179/026708385790124459
Dellis, 1991, The wear properties of aluminium alloy composite, Mater. Sci. Eng., 135A, 253, 10.1016/0921-5093(91)90572-5
Rohatgi, 1991, Cast aluminium matrix composites for automotive applications, J. Met., 10
J. Dinwoodie, Automotive applications for MMCs based on short staple alumina fibres, SAE Technical Paper Series, Int. Con. Exp., Detroit, MI, 1987, pp. 23–27.
Joshi, 1995, Development of the technology for discontinuously reinforced aluminium composites, 492
Kocazac, 1993, MMCs, for ground vehicle aerospace and industrial applications, 297
Chadwich, 1990, Machining of metal matrix composites, Met. Mater., 2–6, 73
Das, 1988, 139
Prasad, 1997, The effect of alumina fibres on the sliding wear of cast aluminium alloy, Composites, 28A, 301, 10.1016/S1359-835X(96)00115-7
Sahin, 2002, Tool wear and surface roughness of Al2O3 particle-reinforced aluminium alloy composites, J. Mater. Process. Technol., 128, 280, 10.1016/S0924-0136(02)00467-3
Taha, 1998, Metal-matrix composites fabricated by pressure-assisted infiltration of loose ceramic powder, J. Mater. Process. Technol., 73, 139, 10.1016/S0924-0136(97)00223-9
S. Lafreniere, G.A. Irons, in: International Symposium on Production, Refining, Fabrication and Recycling of Light Metals, Hamilton, ON, 1990, p. 177.
Ibrahim, 1991, Particulate reinforced metal matrix composites: a review, J. Mater. Sci., 26, 1137, 10.1007/BF00544448
Banerji, 1984, Metallurgy, 38, 656
Asthana, 1992, Z. Metall, 83, 887
Stefanescu, 1993, 79–80, 75
Skolianos, 1993, Dry wear of particulate reinforced composite, Mater. Sci. Eng. A, 163, 107, 10.1016/0921-5093(93)90584-2
Y. Sahin, The mechanical, friction and wear behaviour of B(SiC) fibre-reinforced metal and plastic composites, Ph.D. Thesis, Aston University in Birmingham, UK, 1994.
Pramila Bai, 1992, Dry sliding wear of A356-Al-SiCp composites, Wear, 157, 295, 10.1016/0043-1648(92)90068-J
Ma, 1996, Dry wear of alumina based composites, Mater. Sci. Technol., 12, 751, 10.1179/mst.1996.12.9.751
M. Kok, Production of Metal Matrix (Al2O3-reinforced) Composite Materials and Investigation of Their Machinability by Ceramic Tools, Ph.D. Thesis, Firat University, Elazığ, Turkey, 2000.
Milliere, 1988, Fabrication and properties of metal matrix composites based on SiC fibre reinforced aluminium alloys, Mater. Sci. Technol., 4, 41, 10.1179/mst.1988.4.1.41
Hung, 1995, Machinability of cast and powder-formed aluminum alloys reinforced with SiC particles, J. Mater. Process. Technol., 48, 291, 10.1016/0924-0136(94)01661-J
McLean, 1997, SiC particulate-reinforced, aluminium-matrix composite rods and wires produced by a new continuous casting route, Composites, Part A, 28, 153, 10.1016/S1359-835X(96)00107-8
Ghost, 1988, Influence of process parameters on the porosity content in Al(Mg)-alumina cast particulate composite produced by Vortex method, AFS Trans., 775–782, 88
McCoy, 1988, Dendiritic segregation in particle-reinforced cast aluminium composites, 77