Power transmission dynamics in micro and macro slip regions for a metal v-belt continuously variable transmission under external vibrations
Tóm tắt
In this paper, the power transmission dynamics of a metal v-belt continuously variable transmission (CVT) under external vibration conditions were investigated for the micro and macro slip regions. A CVT variator simulator was developed based on the CVT power transmission dynamics. Using the simulator, the influence of a slip on the external vibration transmission characteristics was analyzed in time and frequency domain. From the analysis results, it was found that the external vibration transmission characteristics were different between the micro slip region and the macro slip region. In the micro slip region, the vibrations of the primary and the secondary pulleys were coupled, which means that the vibration characteristics of the primary and secondary pulleys are determined by the torque vibrations characteristics of both the primary and secondary torque. However, in the macro slip region, the vibrations of the pulleys are decoupled and the vibration characteristic of each pulley is determined by the torque vibration of the corresponding side. Experiments were performed to validate the external vibration transmission characteristics for the load torque fluctuation. The test results were in good agreement with the simulation results. It is expected that the different vibration transmission characteristics of the micro and macro slip regions can be used to detect a macro slip in the CVT variator during actual operation.
Tài liệu tham khảo
Bonsen, B., Klaassen, T. W. G. L., van de Meerakker, K. G. O., Steinbuch, M. and Veenhuizen, P. A. (2003). Analysis of slip in a continuously variable transmission. 2003 ASME Int. Mechanical Engineering Cong., 3, 15–21.
Bonsen, B., Klaassen, T. W. G. L., van der Meerakker, K. G. O., Steinbuch, M. and Veenhuizen, P. A. (2004). Measurement and control of slip in a continuously variable transmission. CVT-HYBRID 2004, 77–79.
Chauvin, J., Corde, G., Philippe, M., Castagné, M., Nicolas, P. and Pierre, R. (2004). Time-varying linear observer for torque balancing on a DI engine. Proc. Volume from the 10th IFAC Symp., 137–143.
Doi, T. (2010). New compact, lightweight, low friction CVT with wide ratio coverage. CVT-HYBRID 2010, 146–151.
Faust, H., Homm, M. and Reuschel, M. (2002). Efficiency-optimised cvt hydraulic and clamping system. CVT 2002 Cong., 43–58.
Fujii, T., Kurokawa, T. and Kanehara, S. (1993). A study of a metal pushing v-belt type CVT-Part 1: Relation between transmitted torque and pulley thrust. SAE Paper No. 930666.
Gao, H., Lam, J. and Wang, C. (2006). Multi-objective control of vehicle active suspension system via loaddependent controllers. J. Sound Vibr., 645–675.
Kim, T. and Kim, H. (2000). Low Level Control of metal belt CVT considering shift dynamics and ratio valve onoff characteristics. KSME Int. J. 14, 6, 645–654.
Lebrecht, W., Pfeiffer, F. and Ulbrich, H. (2004). Analysis of self-induced vibrations in a pushing v-belt CVT. CVT 2004 Cong., 266–276.
Nishizawa, H., Yamaguchi, H. and Suzuki, H. (2005). Friction characteristics analysis for clamping force setup in metal v-belt type CVTs. R&D Review of Toyota CRDL 40, 3, 14–20.
Rothenbühler, Y. (2009). New slip synthesis and theoretical approach of CVT slip control. Diss. ÉCOLE POLYTECHNIQUE FÉDÉRALE DE LAUSANNE.
Ryu, W. and Kim, H. (2009). CVT ratio control with consideration of CVT system loss. Int. J. Automotive Technology 9, 4, 459–465.
Sakagami, K., Fujii, T., Yoshida, H. and Yagasaki, T. (2007). Study on belt slip behavior in metal v-belt type CVT. CVT-HYBRID 2007, 20074565, 135–139.
van der Laan, M. and van Drogen, M. (2005). Improving push belt CVT efficiency by clamping force control strategies based on variator slip measurement. TVT 2005 Cong., 2005, 8–13.
van der Meulen, S., van der Noll, E., de Jager, B., van der Sluis, F., Veenhuizen, B. and Steinbuch, M. (2007). Experimental investigation of macro-slip in a push belt CVT variator. CVT-HYBRID 2007, 43–48.
van der Noll, E., van der Sluis, F., van Dongen, T. and van der Velde, A. (2009). Innovative self-optimising clamping force strategy for the push belt CVT. SAE World Cong. 2009, SAE Paper No. 2009-01-1537.
van der Sluis, F., van Dongen, T. and van Spijk, G. (2007). Efficiency optimization of the pushbelt CVT. SAE Technical Paper, 313–321.
van Drogen, M. and van der Laan, M. (2004). Determination of variator robustness under macro slip conditions for a push belt CVT. SAE World Cong. 2004, 85–100.
Yamaguchi, H., Tani, H. and Hayakawa, K. (2006). Measurement and estimation technologies for the experimental analysis of metal v-belt type CVTs. Research paper, R&D Review of Toyota CRDL 40, 3, 6–13.
Zheng, G., Lim, W. and Cha, S. (2011). Performance optimization of CVT for two-wheeled vehicles. Int. J. Automotive Technology 12, 3, 461–468.