Optimization of laser micromachining of Ti–6Al–4V

Chen, 2018, Ultrasonic vibration assisted grinding of CFRP composites: effect of fiber orientation and vibration velocity on grinding forces and surface quality, Int. J. Lightweight Mater. Manuf., 1, 189 Stráský, 2011, The effect of microstructure on fatigue performance of Ti–6Al–4V alloy after EDM surface treatment for application in orthopaedics, J. Mech. Behav. Biomed. Mater., 4, 1955, 10.1016/j.jmbbm.2011.06.012 Iqbal, 2019, Comparative analyses of multi-pass face-turning of a titanium alloy under various cryogenic cooling and micro-lubrication conditions, Int. J. Lightweight Mater. Manuf., 2, 388 Xu, 2018, Tool wear investigation in high-pressure jet coolant assisted machining Ti2AlNb intermetallic alloys based on FEM, Int. J. Lightweight Mater. Manuf., 1, 219 Dubey, 2008, Laser beam machining—a review, Int. J. Mach. Tool Manuf., 48, 609, 10.1016/j.ijmachtools.2007.10.017 Dubey, 2008, Experimental study of Nd:YAG laser beam machining—an overview, J. Mater. Process. Technol., 195, 15, 10.1016/j.jmatprotec.2007.05.041 Ghany, 2005, Cutting of 1.2mm thick austenitic stainless steel sheet using pulsed and CW Nd:YAG laser, J. Mater. Process. Technol., 168, 438, 10.1016/j.jmatprotec.2005.02.251 Lamikiz, 2005, CO2 laser cutting of advanced high strength steels (AHSS), Appl. Surf. Sci., 242, 362, 10.1016/j.apsusc.2004.08.039 Chen, 1999, The effects of high-pressure assistant-gas flow on high-power CO2 laser cutting, J. Mater. Process. Technol., 88, 57, 10.1016/S0924-0136(98)00402-6 Rajaram, 2003, CO2 laser cut quality of 4130 steel, Int. J. Mach. Tool Manuf., 43, 351, 10.1016/S0890-6955(02)00270-5 Karatas, 2006, Laser cutting of steel sheets: influence of workpiece thickness and beam waist position on Kerf size and stria formation, J. Mater. Process. Technol., 172, 22, 10.1016/j.jmatprotec.2005.08.017 Rao, 2009, Multi-objective optimization of Nd:YAG laser cutting of thin superalloy sheet using grey relational analysis with entropy measurement, Opt. Laser. Technol., 41, 922, 10.1016/j.optlastec.2009.03.008 Dubey, 2008, Multi-objective optimization of laser beam cutting process, Opt. Laser. Technol., 40, 562, 10.1016/j.optlastec.2007.09.002 Kuar, 2006, Modelling and analysis of pulsed Nd:YAG laser machining characteristics during micro-drilling of zirconia (ZrO2), Int. J. Mach. Tool Manuf., 46, 1301, 10.1016/j.ijmachtools.2005.10.016 Dhupal, 2009, Modeling and optimization on Nd:YAG laser turned micro-grooving of cylindrical ceramic material, Opt. Lasers Eng., 47, 917, 10.1016/j.optlaseng.2009.03.016 Mathew, 1999, Parametric studies on pulsed Nd: YAG laser cutting of carbon fibre reinforced plastic composites, J. Mater. Process. Technol., 89, 198, 10.1016/S0924-0136(99)00011-4 Teimouri, 2019, Sustainable drilling process of 1045 steel plates regarding minimum energy consumption and desired work quality, Int. J. Lightweight Mater. Manuf., 2, 397 Teimouri, 2017, Experimental study and empirical analysis on effect of ultrasonic vibration during rotary turning of aluminum 7075 aerospace alloy, J. Manuf. Process., 26, 1, 10.1016/j.jmapro.2016.11.011 Aminian, 2015, Application of soft computing techniques for modeling and analysis of MRR and taper in laser machining process as well as weld strength and weld width in laser welding process, Soft Comput., 19, 793, 10.1007/s00500-014-1305-x Hashemzadeh, 2014, Fibre laser piercing of mild steel – the effects of power intensity, gas type and pressure, Opt. Lasers Eng., 55, 143, 10.1016/j.optlaseng.2013.10.001 Khan, 2019, Multi-objective optimization of energy consumption and surface quality in nanofluid SQCL assisted face milling, Energies, 12, 710, 10.3390/en12040710 Mia, 2019, Multi-objective optimization and life cycle assessment of eco-friendly cryogenic N2 assisted turning of Ti-6Al-4V, J. Clean. Prod., 210, 121, 10.1016/j.jclepro.2018.10.334