Optimal weaving for 2.5D interlocks

Baeten, 1999, Optimization of a GMT-based cold pressing technique for low cost textile reinforced thermoplastic composites, Compos Part A: Appl Sci Manuf, 30, 667, 10.1016/S1359-835X(98)00173-0 Barlow, 2002, Preliminary study on cost optimization of aircraft composite structures applicable to liquid molding technologies, Compos Struct, 57, 53, 10.1016/S0263-8223(02)00062-4 Berthelot JM. Matériaux composites: comportement mécanique et analyse des structures. Edition Masson, 1992. Coneciao, 1995, Optimization of laminated composite structures using a bilevel strategy, Compos Struct, 33, 193, 10.1016/0263-8223(95)00102-6 Diaconu, 2002, Buckling characteristics and layup optimization of long laminated composite cylindrical shells subjected to combined loads using lamination parameters, Compos Struct, 58, 423, 10.1016/S0263-8223(02)00130-7 Duvaut G, Desmorat B, Deletombe E. Optimisation de renforts composites internes de structure tridimensionnelles. CR Acad Sci Paris série II b 2001;329:549–55. Duvaut, 2001, A new elasticity problem and its application to the optimal wrapping, Compos Struct, 54, 149, 10.1016/S0263-8223(01)00083-6 El Hage Ch. Modélisation du comportement élastique endommageable de matériaux composites à renfort tridimensionnel. PhD thesis, Université de Technologie de Compiègne, 2006. Farshi, 2006, Optimum weight design of fiber composite plates in flexure based on a two level strategy, Compos Struct, 73, 495, 10.1016/j.compstruct.2005.03.002 Gokce, 2002, Branch and bound search to optimize injection gate locations in liquid composite molding processes, Composites Part A, 33, 1263, 10.1016/S1359-835X(02)00047-7 Grosset L. Optimization of composite structures by estimation of distribution algorithms. PhD thesis, University of Florida, 2004. Hexcel Composite 2008. <http://www.hexcel.com>. Hsiao, 2006, A study of direct cure kinetics characterization during liquid composite molding, Compos Part A: Appl Sci Manuf, 37, 925, 10.1016/j.compositesa.2005.01.019 Kassapoglou, 1998, Minimum cost and weight design of fuselage frames part B: cost consideration, optimization and results, Composites Part A, 30, 895, 10.1016/S1359-835X(98)00191-2 Khellil K. Evaluation expérimentale d’un critère de rupture tensoriel polynomial tridimensionnel pour matériaux composites. PhD thesis, Université de Technologie de Compiègne, 1993. Lawrence, 2002, An approach to couple mold design and online control to manufacture complex composite parts by resin transfer molding, Compos Part A: Appl Sci Manuf, 33, 981, 10.1016/S1359-835X(02)00043-X Minoux M. Programmation mathématique. Tome 1 & 2, Editions Dunod, 1983. Pantelelis, 2003, Optimized cure cycles for resin transfer molding, Compos Sci Technol, 63, 249, 10.1016/S0266-3538(02)00196-3 Park, 2001, Stacking sequence design of composite laminates for maximum strength using genetic algorithms, Compos Struct, 52, 217, 10.1016/S0263-8223(00)00170-7 Scida D. Etude et modélisation du comportement mécanique des matériaux composites à renfort tissés hybrides et non hybrides. PhD thesis, Université de Technologie de Compiègne, 1998. Smervov, 2000, A computational study in optimum formulations of optimization problems on laminated cylindrical shells for buckling. i. Shells under axial compression, Compos Sci Technol, 60, 2057, 10.1016/S0266-3538(00)00102-0 Todoroki, 1998, Stacking sequence optimization by a genetic algorithm with a new recessive gene like repair strategy, Composites Part B, 29B, 277, 10.1016/S1359-8368(97)00030-9 Torayca 2008, fibre de carbone. <http://www.soficar-carbon.com>. User’s Guide, Optimization toolbox for use with Matlab. The MathWorks edition, version 2006b. Verchery G. Les invariants des tenseurs d’ordre 4 du type de l’élasticité. Proc of Colloque Euromech 115, Villard-de-Lans, 1979. Published by Editions du CNRS, Paris; 1982. p. 93–104. Walker, 2003, A technique for the multi-objective optimization of laminated composite structures using genetic algorithms and finite element analysis, Compos Struct, 62, 123, 10.1016/S0263-8223(03)00098-9 Wang, 2002, Multi-objective optimization of composite aerospace structures, Compos Struct, 57, 141, 10.1016/S0263-8223(02)00078-8 Zingraff, 2005, Resin transfer molding of anionically polymerized polyamide 12, Compos Part A: Appl Sci Manuf, 36, 1675, 10.1016/j.compositesa.2005.03.023