On pre and post-processing of 3D printed ABS thermoplastic sacrificial pattern for strategic dog teeth
Tóm tắt
The fabrication of dental crowns (DC) for humans with fused filament fabrication (FFF) followed by investment casting (IC) has been the commercial practice for the past 20 years. However, little has been reported on FFF-based 3D printing of DC for strategic teeth (ST) of veterinary patients (VP), especially in assembly fit. The present study highlights the detailed methodology for the preparation of acrylonitrile butadiene styrene (ABS) DC master pattern (of mandibular first molar (M1) and maxillary fourth pre-molar (PM4) tooth) of a 3-year-old German shepherd dog as a subject. The PM4-M1 combination as ST has geometrical complexity and is important during mastication, requiring tight tolerance to justify assembly fit. This paper explores the role of FFF-based pre-post-processing variables on the geometrical complexity of DC (M1 and PM4) of a dog while assembly in terms of international tolerance (IT) grades. Results of the study suggest that the best settings of FFF for dimensional accuracy (∆d) and surface hardness of master DC pattern prepared are as follows: low part density, 180° orientation angle, and post-treatment temperature of 80 °C (based upon multifactor optimization). The results from this study are supported by scanning electron microscopy (SEM), 3D rendered images, and surface texture profiles.
Tài liệu tham khảo
Arif ZU, Khalid MY, Ahmed W, Arshad H (2022) A review on four-dimensional bioprinting in pursuit of advanced tissue engineering applications. Bioprinting 27:e00203
Bae EJ, Jeong ID, Kim WC, Kim JH (2017) A comparative study of additive and subtractive manufacturing for dental restorations. J Prosthet Dent 118(2):187–193
Khalid MY, Al Rashid A, Arif ZU, Ahmed W, Arshad H (2021) Recent advances in nanocellulose-based different biomaterials: types, properties, and emerging applications. J Market Res 14:2601–2623
Singh S, Ramakrishna S, Singh R (2017) Material issues in additive manufacturing: a review. J Manuf Process 25:185–200
Khalid MY, Arif ZU, Ahmed W (2022) 4D Printing: technological and manufacturing renaissance. Macromol Mater Eng 307(5):2200003
Mitchell CA, Orr JF (2005) Engineering properties and performance of dental crowns. Proc Inst Mech Eng 219(4):245–255
Eggbeer D, Bibb R, Williams R (2005) The computer-aided design and rapid prototyping fabrication of removable partial denture frameworks. Proc Inst Mech Eng [H] 219(3):195–202
Lee S, Hong SJ, Paek J, Pae A, Kwon KR, Noh K (2019) Comparing accuracy of denture bases fabricated by injection molding, CAD/CAM milling, and rapid prototyping method. J Adv Prosthodontics 11(1):55–64
Deradjat D, Minshall T (2017) Implementation of rapid manufacturing for mass customisation. J Manuf Technol Manag 28(1):95–121
Pradhan SR, Singh R, Banwait SS, Singh S, Anand A (2021) 3D Printing assisted dental crowns for veterinary patients. Ref Module Mater Sci Mater Eng. https://doi.org/10.1016/B978-0-12-820352-1.00153-X
Deb S (1998) Polymers in dentistry. Proc Inst Mech Eng 212(6):453–464
Ma Q, Rejab MRM, Kumar AP, Fu H, Kumar NM, Tang J (2020) Effect of infill pattern, density and material type of 3D printed cubic structure under quasi-static loading. Proc Inst Mech Eng Part C J Mech Eng Sci 2020:1–19. https://doi.org/10.1177/954406220971667
Gupta Y, Iyer R, Dommeti VK, Nutu E, Rana M, Merdji A, Biswas JK, Roy S (2021) Design of dental implant using design of experiment and topology optimization: a finite element analysis study. Proc Inst Mech Eng 235(2):157–166
Nsengimana J, Van der Walt J, Pei E, Miah M (2019) Effect of post-processing on the dimensional accuracy of small plastic additive manufactured parts. Rapid Prototyping J 25(1):1–12
Kumar N, Kumar JP (2019) Analysing the influence of raster angle, layer thickness, and infill rate on the compressive behaviour of EVA through CNC-assisted fused layer modelling process. Proc Inst Mech Eng Part C J Mech Eng Sci 2019:1–10. https://doi.org/10.1177/954406219889076
Dave HK, Patadiya NH, Prajapati AR, Rajpurohit SR (2019) Effect of infill pattern and infill density at varying part orientation on tensile properties of fused deposition modeling-printed poly-lactic acid part. Proc Inst Mech Eng Part C J Mech Eng Sci 2019:1–17. https://doi.org/10.1177/954406219856383)
Keleş O, Blevins CW, Bowman KJ (2017) Effect of build orientation on the mechanical reliability of 3D printed ABS. Rapid Prototyping J 23(2):320–328
Capik I, Ledecky V, Sevcik A (2000) Tooth fracture evaluation and endodontic treatment in dogs. Acta Vet Brno 69(2):115–122
Rekow D, Thompson VP (2005) Near-surface damage-a persistent problem in crowns obtained by computer-aided design and manufacturing. Proc Inst Mech Eng 219(4):233–243
Suryawanshi AS, Behera N (2020) Tribological behavior of dental restorative composites in chewable tobacco environment. Proc Inst Mech Eng 234(10):1106–1112
Dawood A, Purkayastha S, Patel S, MacKillop F, Tanner S (2010) Microtechnologies in implant and restorative dentistry: a stroll through a digital dental landscape. Proc Inst Mech Eng 224(6):789–796
Pradhan SR, Singh R, Banwait SS (2020) A-frame work on crown fabrication for veterinary patients using 3D thermoplastic and metal printing. Ref Module Mater Sci Mater Eng. https://doi.org/10.1016/B978-0-12-820352-1.00063-8
Lemmons M, Beebe D (2019) Oral anatomy and physiology. Wiggs’s Vet Dentistry Principles Pract. 2019:1–24
Ojeda J, Martínez-Reina J, García-Aznar JM, Domínguez J, Doblare M (2011) Numerical simulation of bone remodelling around dental implants. Proc Inst Mech Eng 225(9):897–906
Lo YJ, Chang WJ, Lee SY, Chang KJ, Lin CT, Huang HM (2009) Reductions in the effects of damping on stress concentration in premolars by post-endodontic restorations: a non-linear finite element study. Proc Inst Mech Eng 223(5):555–565
Coffman C, Visser C, Soukup J, Peak M (2019) Crowns and prosthodontics. Wiggs’s Vet Dentistry Principles Pract 2019:387–410
Singh G, Singh R, Bal SS (2020) Investigations for partial denture casting by fused deposition modeling-assisted chemical vapour smoothing. Assem Autom 40(5):745–754
Ashley M, McCullagh A, Sweet C (2005) Making a good impression:(a’how to’paper on dental alginate). Dent Update 32(3):169–170
Al Qahtani MA, Alrefaie M, Altamimi A, Aljowyed I, Al Qahtani MA, AlQahtani A, Habib SR (2019) Evaluation of pre-alginate impression preparation methods in the surface accuracy of dental cast. Saudi Dental J 31(4):451–456
Hayashi K, Sachdeva AU, Saitoh S, Lee SP, Kubota T, Mizoguchi I (2013) Assessment of the accuracy and reliability of new 3-dimensional scanning devices. Am J Orthod Dentofac Orthop 144(4):619–625
Bansal M, Dhami SS (2009) 3D Scanning for reverse engineering-technological advancements, process overview, accuracy inspection, challenges, and remedies. Int J Emerg Technol Eng Res 10(5):33–40
Li S, Chen J, Kula KS (2019) Comparison of movement rate with different initial moment-to-force ratios. Am J Orthod Dentofac Orthop 156(2):203–209
Gagg G, Ghassemieh E, Wiria FE (2013) Analysis of the compressive behaviour of the three-dimensional printed porous titanium for dental implants using a modified cellular solid model. Proc Inst Mech Eng [H] 227(9):1020–1026
Nayak A, Jain PK, Kankar PK, Jain N (2021) Effect of volumetric shrinkage of restorative materials on tooth structure: a finite element analysis. Proc Inst Mech Eng 235(5):493–499
Häsler R, Schmid G, Ingervall B, Gebauer U (1997) A clinical comparison of the rate of maxillary canine retraction into healed and recent extraction sites—a pilot study. Eur J Orthod 19(6):711–719
Clift SE, Fisher J, Watson CJ (1993) Stress and strain distribution in the bone surrounding a new design of dental implant: a comparison with a threaded Branemark type implant. Proc Inst Mech Eng 207(3):133–138
Genovese K, Lamberti L, Pappalettere C (2006) Structural behaviour of endodontically treated teeth under thermomechanical loading. Proc Inst Mech Eng 220(8):909–928
Rees JS (2006) The biomechanics of abfraction. Proc Inst Mech Eng 220(1):69–80
Singh JP, Singh R (2009) Investigations for statistically controlled rapid casting solution of low brass alloys using three-dimensional printing. Int J Rapid Manuf 1(2):208–221
DiBenedetto AT (1987) Prediction of the glass transition temperature of polymers: a model based on the principle of corresponding states. J Polym Sci Part B: Polym Phys 25(9):1949–1969
Singh P, Pungotra H, Kalsi NS (2020) Parametric optimization of deep cryogenic treatment for the wear response of implant material UNS R56700: Taguchi’s approach. Proc Inst Mech Eng 234(1):61–73
Rahman M, Schott NR, Sadhu LK (2016) Glass transition of ABS in 3D printing. In: COMSOL Conference, Boston, pp 1–5
Yazdi MH, Lee-Sullivan P (2009) Determination of dual-glass transition temperatures of a PC/ABS blend using two TMA modes. J Therm Anal Calorimetry 96(1):7–14
Pradhan SR, Singh R, Banwait SS (2021) On crown fabrication in prosthetic dentistry of veterinary patients: a review. Adv Mater Process Technol 2021:1–20. https://doi.org/10.1080/2374068X.2021.1970991