Numerical and experimental investigation of a wire-net compact heat exchanger performance for high-temperature applications

Pehnt, 2006 Hawkes, 2007, Cost-effective operating strategy for residential micro-combined heat and power, Energy, 32, 711, 10.1016/j.energy.2006.06.001 IEA Energy Efficiency Policy Recommendations, 2011. Delanaye, 2017, Development of a recuperated flameless combustor for an inverted Bryton cycle microturbine used in residential micro-CHP Beith, 2011 Balaras, 1990, A review of augmentation techniques for heat transfer surfaces in single-phase heat exchangers, Energy, 15, 899, 10.1016/0360-5442(90)90071-9 Roeller, 1991, Heat transfer and turbulent flow characteristics of isolated three-dimensional protrusions in channels, J. Heat Transf., 113, 597, 10.1115/1.2910607 Tao, 2002, A unified analysis on enhancing single phase convective heat transfer with field synergy principle, Int. J. Heat Mass Transf., 45, 4871, 10.1016/S0017-9310(02)00173-4 Paolo, 2016, Conjugate heat and mass transfer in drying: a modeling review, J. Food Eng. Fiebig, 1995, Vortex generators for compact heat transfer exchangers, J. Enhanced Heat Transf., 2, 43, 10.1615/JEnhHeatTransf.v2.i1-2.60 Incropera, 1996 Fiebig, 1998 Johnson, 1969, The influence of vortex generators on the drag and heat transfer from a circular cylinder normal to an airstream, J. Heat Transf., 91, 91, 10.1115/1.3580126 Hajime, 2001, Local heat transfer around a wall-mounted cube in the turbulent boundary layer, Int. J. Heat Mass Transf. Meinders, 1999, Experimental study of the local convection heat transfer from a wall-mounted cube in turbulent channel flow, J. Heat Transf., 121, 564, 10.1115/1.2826017 Valencia, 2000, Turbulent flow and heat transfer in a channel with a square bar detached from the wall, Numer. Heat Transf.: Part A: Appl., 37, 289, 10.1080/104077800274307 Meis, 2010, Heat transfer enhancement in micro-channels caused by vortex promoters, Int. J. Heat Mass Transf., 10.1016/j.ijheatmasstransfer.2009.10.013 Turnow, 2012, Flow structures and heat transfer on dimples in a staggered arrangement, Int. J. Heat Fluid Flow, 35, 168, 10.1016/j.ijheatfluidflow.2012.01.002 Croce, 2007, Three-dimensional roughness effect on micro-channel heat transfer and pressure drop, Int. J. Heat Mass Transf., 50, 5249, 10.1016/j.ijheatmasstransfer.2007.06.021 Morini, 2007, The role of the viscous dissipation in heated microchannels, ASME J. Heat Transf., 129, 308, 10.1115/1.2430725 Yang, 2014, Design and experimental investigation of a gas-to-gas counter-flow micro heat exchanger, Exp. Heat Transf., 27, 340, 10.1080/08916152.2013.849179 Yang, 2014, Experimental analysis of the influence of wall axial conduction on gas-to-gas micro heat exchanger effectiveness, Int. J. Heat Mass Transf., 69, 17, 10.1016/j.ijheatmasstransfer.2013.10.008 Kays, 1964 Kanaris, 2009, Optimal design of a plate heat exchanger with undulated surfaces, Int. J. Therm. Sci., 48, 1184, 10.1016/j.ijthermalsci.2008.11.001 Pelletier, 2005, CFD simulation of heat transfer in compact brazed plate heat exchangers, ASHRAE Trans., 111, 846 Yang, 2003, Calculation of turbulent flow and heat transfer in a porous-bed channel, Int. J. Heat Mass Transf., 46, 771, 10.1016/S0017-9310(02)00360-5 Fu, 2017, An experimental investigation on heat transfer enhancement of sprayed wire-mesh heat exchangers, Int. J. Heat Mass Transf., 112, 699, 10.1016/j.ijheatmasstransfer.2017.05.026 Hasan, 2009, Influence of channel geometry on the performance of a counter flow microchannel heat exchanger, Int. J. Therm. Sci., 48, 1607, 10.1016/j.ijthermalsci.2009.01.004 Schlichting, 2017 Hong, 2019, Data reduction of average friction factor of gas flow through adiabatic micro-channels, Int. J. Heat Mass Transf., 129, 427, 10.1016/j.ijheatmasstransfer.2018.09.088 George Y. Lai, High-temperature corrosion and material applications. W. Qiuwang, C. Qiuyang, W. Ling, Z. Min, H. Yanping, X. Zejun, Experimental study of heat transfer enhancement in narrow rectangular channel with longitudinal vortex generators, Nucl Eng Des, 2007 (ISBN: 0029-5493). Mahmud, 2001, Numerical prediction of fluid flow and heat transfer in a wavy pipe, J. Therm. Sci., 10, 133, 10.1007/s11630-001-0054-1 Vivianne, 2012 Pope, 2000 E. Andrew, C. Jie, Comparison of turbulence models in simulating swirling pipe flows, Appl. Math. Model., 34 (2010) 2840–2849, 2010 (ISBN:0307-904X). Remi Manceau, Industrial codes for CFD. Farhana, 2018, Vol. 50, Number 2